Topics Last Week

MAN remember the heady days of me celebrating that it was just a matter of screwing something in? Man those were the days. I took it out tonight and within about a minute or so of using the brake pedal it went pretty much straight to the floor now that it was stopping mass I guess. I headed back home and now there is fluid leaking out of the bottom of both where the front and rear brake lines screw in. Time to trash this master, right?

It got a nice price when it had the L6. $46,200. Not sure that 454 is going to add value. I'd guess most of the aftermarket parts went on after that sale. No driving video yet. 1971 Datsun 240Z VIN HLS3042112 | Hagerty Valuation ToolsHave you seen this 1971 Datsun 240Z VIN HLS3042112 auction result?

Grab a torch - propane will do - and melt the body lead out of that section. That'll give you a better idea of how that sheet metal is shaped and spot welded together. There will be body lead in various places all up and down that pillar. The lead will probably have saved the sheet metal up near the window flange - and may give you a good clean section to weld to at that end.

I was describing its function, not the actual material wire. The trigger wire for the new tach is its own independent circuit. I was also trying to tease out if you're replacing the stock tach or adding another tach. Are you sticking the new tach in the hole where the old one is? Your other basic question might be "how do I keep my ignition system functioning if I remove my factory tach?". Since they are tied together in the 240Z's. Just breaking the "how do I connect my new tach?" question in to its elements. Seems like you're on top of it. Good luck.

Good advice, just got home from work, will go put the alternator in. I assume I should see continuity from the alternator output wire to the positive battery cable? Will check that before I hook up the battery and see if there is 12 volts on the "T" connector with the key on.

I have been using that bosch relay in the photo since 2012 and no issues. Plugged in a go. The bosch relay was used in the first 280Z in 1974. Datsun used a Bosch L-Jetronic system for the first 6 months of the 280Z production And Hitachi copied it. That is why a lot of Bosch parts will work on these efi systems. I think @Mike had a bosch system in his attic once. I posted an ebay link back in 2018 and it still works😄 https://www.ebay.com/p/77006951

What changes did he make to get all the plugs firing evenly?

https://www.amazon.com/Zig-furniture-upholstery-tempered-sinuous/dp/B01FE3PSZE

I got the rotary replacement kit from the Z Store (ZStore.com) but not sure if they still have the kits.

Ah yes. The "right setup" would include proper harnessing (no cutting or splicing), relays to isolate the power, adequate drivers for the blubs, no flicker, and adequate cooling. Also my opinion of the right setup would make it look period-correct for the car. Overall, I believe the only real reason to consider LED is to provide more powerful light output for driving. There's no real power savings needed on a gas powered car unless maybe to support a lower rated alternator. In my case, I don't really need LED unless I just want to go down that path for fun. I also considered LED's for my Land Cruiser, because the light output is pretty weak. However, I also decided against it because I couldn't find many options that met my requirement above.

Also, Japanese market variants had the option of factory stereo from beginning of production, so there are speaker holes in both sides of the interior quarter panel trims and the sheetmetal underneath them was designed to accept speaker mounts on both sides.

😎

Never seen the last type. Suspect it is a retro fit that someone did from some other car. The first one is 240, second is 280, though can’t nail down the change over date. Could be as early as the north american 260 in 74. The fiche might provide the date info

Contact Oliver at Zspecialties to see if he has any. https://zspecialties.com/ I suggest calling him at the number at that website. Over at zcar.com, his user name is zmanofwashington.

1977 280z AFM from an EFI engine. Car had been sitting, everything looks in working order. asking $150 obo. located in Gilbert AZ

I worked on the heat shield/ cable bracket some more today. Here is the current pattern An earlier template on a piece of coil metal I glued it to piece of 16ga I had laying around A little cutting We will have to clearance it around some of the header pipes. Since it's an equal length header, they intrude on the carb area more than some We will use some stainless exhaust tube to deal with the clearanced areas. Once I finalize a design I will have sendcutsend fabricate it for me

I also got the tool covers from resurrected classics and got them installed A little nerve racking to bend the plastic hinges to mount them

Planning to swap an R200 into my Series 1 car (12/70 build date) and am looking for the mustache bar, front diff mount and insulator and the rear transverse link mount from a later 280Z that came with the R200.

Sent PM

Awe man this is a trap!

S30 parts are rare and expensive. Not enough competition or volume of sales to keep the price down.

This is the other name and email used during the email communications with Sully. Phaedra Rosengarth armychick44@hotmail.com He sent several pictures of the new tank and a few pictures of a partially restored tank that he allegedly was working on.

@Mike

For sale are 3 280zx gauge clusters (without clocks). One is for a right hand drive. I make no claim as to the function of the 2 gauges per cluster, but they should be good. Asking $15 plus shipping If interested contact me @ ron@zclocks.com

This bot is not like the others. The link actually leads to a real business. In Dubai.