Topics Last 30 Days

Thankyou gents for your replies. I've mounted the car. Sat down after two days of endless measuring, laser levels. 3 spirit levels...... absolutly perfect. Had to pry the shock towers in....they seemed to be out by about 8mm. Yeah its crash damage I think. So I sit down in the heat. Crack a beer. And celebrate my days of handy work...... Then.... I read what is written above.....that the towers will be 7mm out if you meausre it wrong........ Ok so tomorrow I'll pull that strut mount off and redo it. Some awsome tips. Thanks again! I put the doors on yesterday and gapped them.....a tip for you all. Im a woodworker too and the best gapping tool on the market is a good set of playing cards......

A little late jumping into this conversation. I have been "out of contact" on holiday which I do every so often going internet dark for a few days in my effort to get away from it all. Often, I travel to Europe but I just returned from several days in coastal Maine and that northern wilderness. We were hiking and boating. Reading up on this discussion, I thought I would chime in on some of the issues mentioned. Nissan contracted with four private restoration shops during the Vintage Z program. Pierre Z in Hawthorn, California completed by far the most restorations, however Classic Datsun Motorsports of Vista, California, Datsun Ally of Signal Hill, and Old Car Service of Huntington Beach were also involved. Datsun Ally and Classic Datsun Motorsports prepared two cars each. I don't know how many Old Car Service prepared. Engines were rebuilt and provided by AER Manufacturing in Arington, Texas as transmissions came from Williams Technology of Summerville, South Carolina. Pierre Z rebuilt the units for the first restoration only as Nissan contracted thereon. They were assembled units, crate shipped, including everything except carburetors, generators, cooling fan and hoses, and exhaust manifold to the best of my knowledge. Part management was coordinated through Pete Evanow of Nissan N.A. and there were documents related to car assessment, part orders, and quality control however these were internal project documents related to the management of the project cars and not released with any of the cars. I actually have part order documents for cars that were never restored. Concerning CAD plating: The yellow / gold coloring that we associate with "CAD" is a chromate conversion coating applied over the plated metal, yielding the familiar gold color. A similar appearance can be achieved with a similar chromate conversion over silver zinc which is far less toxic and not easily discernible from a cadmium base electroplate. Cadmium electroplating on its own is not yellow. I believe that what we see on cars today is yellow chromate zinc. True cadmium electroplating is not easily found or inexpensive. We all seem to call it "CAD" but that's probably a term we use for the color and not AS 9100 certified or ASTM A165, SAE AMS 2400 specification. Finally, Nissan N.A. didn't just decide to restore a bunch of 240Zs; they schemed up an ad campaign to keep the Z legend in North America alive while Nissan discontinued their current model Z with only the promise to deliver a new design some time in the future. The goal was not to create 'restorations' but deliver complete, running examples of the original car with 12,000 mile warranties. They had to rely on private repair businesses to accomplish their goal with a parts inventory that could not sustain the project. But they pulled it off! Cudos to the businesses and people who contributed to the effort. The cars are quite valuable now, and it is always exciting to see one because the story behind it is one of the best automotive sales campaign stories. Especially after the blunder of dropping the Datsun brand, I opine. So, I did the research project / compendium in 2005. I have a huge digital file of stuff as well as a fairly good library of literature. I have a vhs video that Pierre gave me in 200? that has Mr. K's visit during the restoration program. I don't have any printed , bound copies at the moment. I hear some interest for copies of stuff I have. I'm going to get some copies of the compendium made. Stay tuned.

Sedan racing

Sticky pistons on 4-screw round tops. Not ideal. About the only things that would account for that would be a) severely misaligned nozzles underneath or b) mismatched domes/pistons. You can check for the mismatching between the domes and pistons by taking the domes off, pulling the pistons out of the carbs and then sliding the pistons into the domes and see if they move smooth and free (while the dome and piston are in your hand, not mounted to the carb body). And you can check for misaligned nozzles/needles by either removing the needles out of the pistons, or by loosening up the nozzle alignment nuts on the under sides the carbs and seeing if the pistons move free while the nozzles are way loose.

Hi cgsheen1! Thanks for the recommendations. I am running the latest version of Microsquirt, 440cc Bosch injectors, Spartan 3 v2, crank 36-1 wheel with HALL sensor, LM7 truck coils with batch firing, AZC oil pan. I will try making Microsquirt work with the turbo (no sequential ignition). I have only one output left (relay) which I can use for an electric fan, for ex. I was aiming for 8-10 lbs of boost to play it safe and keeping my stock rear diff/half-shafts alive. I looked up some parts from rockauto and here is a list if it works? EXEDY 06030 clutch kit, 1975 2+2 Flywheel: AMS AUTOMOTIVE / RHINOPAC 167304, for 2+2 model Throwout bearing, WJB / INMOTION PARTS WRDNE01576C (any manufacturer preference?) Hopefully, if the car parts are for 2+2 model, I am not going to run into any issues with the fitment/clutch fork throw. I just installed a brand new master and slave clutch cylinders (for my 280z 1976 model). Will this create a problem? (I checked the part numbers, they are the same for 76 and 75, I think I should be good here). I started a thread here on hybridz dealing with my project: https://forums.hybridz.org/topic/136053-76-280z-microsquirt-project/ Thanks! Den

I have no idea if I did or not, but feel free to copy it over there, or maybe @Mike can duplicate the post there.

Even though you put a ton of work into fixing up your old garage, I guess it wasn't too difficult to leave it behind in return for a clean, modern garage already equipped with a good floor, good lighting and three bays (not to mention a separate, two-level barn for storing panels and parts. 👍

They have a hinge mount plate on the inside that will fall when the bolts are removed.

Actually, because of safety, some organizing bodies forbid chest straps without something to hold the shoulder belts from slipping out.

I appreciate the explanation and truly feel your pain doing this in the vehicle.

Bit late to the party but I believe my 280z came with the same or allmost the same wheels. Don’t know if they are modified as I haven’t taken the wheels off yet but I must say they look pretty good under my silver Z. Attached is one of the pictures from the auction I bought the car from. The seller also included the original set of wheels but I prefer these. Tire size is 225/60R14 in the rear and 195/70R14 in the front.

Ok I will check on that tomorrow and will update you guys, thanks for the help. I appreciate it a bunch.

Well done Ken. Perseverance par excellence! Dashboards are not fund to work on.

Understood Darom! If you decide you don’t need them and want to get rid of them, just shoot me a message. Thanks!

Hi, I don't think he will respond, but you can get your parts from: Z-Services.eu | Shop for Datsun 240Z, 260Z & 280Z I also have a lot of parts for Z's not specific for the 280z as this was never a euro car.. Oh and yes as my name says i'm from the Netherlands too.

Horror House on Highway Five (1985)

Back to normal programming. This 240Z auction is ending today but it's already up to $23,000. Kind of surprising considering its unusual appearance. It does look clean though. https://bringatrailer.com/listing/1973-datsun-240z-293/

Sure thing!

Rear view mirror, with attach brackets and sun visor support pads, including screws. Missing knob to adjust mirror.

For sale is a rebuilt circuit board for the 75-78 280z OEM clock. The circuit boad is usually what fails. Cost is $80 (includes shipping). For questions contact me at: ron@zclocks.com. Thanks for looking....

I remember my older brother and Dad were swapping a clutch. I jumped in the car, pushed the clutch to the floor, blowing out the slave cylinder. I got out of the car and started running! Fun times. My Dad is now 87 and loves to brag on my mechanic ability. He's my biggest fan.....now. Lots of great memories.

All, The mounted muffler appears to be silver. The unmounted muffler (photos 2 and 3 above) have a greenish tint. Any consensus on the correct color? Thanks, Keith

Bump Anyone have a comment? Keith