Topics Last 30 Days

Well done! Congratulations from another OO.🎉

Hi: We are working on a family '74 260Z project, and finally about to pull the L28 engine with the cracked block out of the car and replace it with another L28. The donor engine had fuel injection, but we are going to replace it with the dual-SU carb setup from the old engine. Someone told me a while back to use a specific set of manifold gaskets in this swap, and I feel like they said it was from an earlier engine, but I have now lost that piece of advice and just wanting to hear from some of you folks who know better than me before I order anything. Check this short video? Thanks in advance! Michael Project Z ICT

Thanks Captain! This is more the info I was looking for. I guess I will be able to verify once my assortment of plugs arrive from Mcmaster.

👍

Do you have any more info for this? Where did you see it?

I offer two different versions of my conversion bell housings to do the reverse tilt. One for the CD009 and one for the TL70. Most of the people that buy my head end up tilting them so I offer the bell housings to assist in that.

Did you read my post?

It will be interesting to see how the BaT S30.world/Garage 44 auction goes when it is (eventually) listed. Im guessing the 240-Z has been shipped to the USA to sell rather than be passed in.

Cannon Manifold and three 40 DCOE 151 (spanish pedigree) weber 151s. I have had these apart and cleaned them but they still need to be gone through and verified. I had them on my Z car running since 2012. Pulled them off and need the space in my garage. Comes with oversized rod ends, and throttle arm mounting bar (less deflection), which is a modification of my own. Carbs are complete. I am pretty sure I have the air horns that came with them. I can ship to anywhere in the CONTIENTAL US, but shipping will be on the purchaser. I will box them up in a protected WEBER carb box individually. For the manifold and carbs I am asking 800 dollars plus shipping. Please give me an email at sdamico555@Gmail.com

They have a 15mm square socket available on Amazon. Works like a champ with a 1/2” pull bar. I chose the Harfington model. https://www.amazon.com/s?k=15mm+socket

@cgsheen1 I was going to post in another thread but didn't want to thread jack, I'm hopeful to make it to Zcon in your area next year and check out your cars

👍

Yes you're correct. However, will a customer accept an exhaust manifold that will start to show corrosion almost the minute he leaves my shop after spending X amount of $ for a Y operation? Asking rhetorically as the answer is obvious. Everyone and I mean EVERYONE was very happy with the Jet-Hot cast look including, but not limited to, the Franklin Mint car.

Zzzzzzzzzz…..

Not that weren’t expecting

I know most people on this forum want as much stock and original parts as possible but, at least it’s my opinion, maybe some modern upgrades / mods are in order to keep these cars on the road. Aside from all the aftermarket suspension upgrades I know that Apex Engineered also sells new steering racks (with right hand inner tie rods) and just the right hand thread inner tie rods. Replacing just the inner tie rod(s) for right hand thread once might be a good solution for the NLA drivers side outer tie rod. And yes Apex does sell them separately and in pairs. https://apexengineered.com/shop/s30-240z-260z-280z/inner-tie-rod/ No I’m not sponsored I just like what they’re doing and ordered some stuff to fix my 280z.

Been a while since showing 2446 bones…and she got good bones. Slowly finding time and discipline to prioritize some shop time. It is fun putting a few peices on the rear, dash will be coming out to recover. Had been a while since I have inverted to disconnect heater control cables….throttle lever cable at top of the gas pedal assembly…etc. rear panel is too dark, debating to reshoot to lighter shade….

I did the yellow/blue wire grounding test. I had both the Floor Temp and Fuel warning lights on. I guess I have an independent to the fuel sender's thermistor issue with the Floor Temp sensor. I will check the relay under the pass seat.

I dont believe the 510 has a rheostat

I am near Canada:)

$840 (plus shipping) at Motorsport Auto.

It doesn’t seem to be.

http://www.zcarblog.com/wp-content/uploads/2022/11/IMG_3902-1024x768.jpeg Happy 89th Birthday to our hero Peter Brock! You have been and continue to be inspirational to us Datsun fans worldwide. Here are a few pictures we enjoyed taking with you over the years: http://www.zcarblog.com/wp-content/uploads/2022/11/unnamed-1-1024x768.jpeghttp://www.zcarblog.com/wp-content/uploads/2021/11/DSC05510-1-e1637002594621-1024x1006.jpeg http://www.zcarblog.com/wp-content/uploads/2016/11/lagunaseca2004153-400x300.jpghttp://www.zcarblog.com/wp-content/uploads/2022/11/IMG_2311-1024x768.jpeghttp://www.zcarblog.com/wp-content/uploads/2021/11/IMG_9747-1024x768.jpeg http://www.zcarblog.com/wp-content/uploads/2022/11/sema-1024x1024.jpghttp://www.zcarblog.com/wp-content/uploads/2022/11/275435624_5253829184651694_278823018715978593_n.jpeghttp://www.zcarblog.com/wp-content/uploads/2024/11/314962664_499938492181328_4586337483149355287_n.jpg http://www.zcarblog.com/wp-content/uploads/2024/11/312177026_483959523779225_1687953212474383395_n.jpg http://www.zcarblog.com/wp-content/uploads/2024/11/382583804_692126209629221_266883468108368867_n.jpg View the full article