Topics Last Week

Not sure where you could get springs. Sorry.

Search Vintage Air

Ah yes. The "right setup" would include proper harnessing (no cutting or splicing), relays to isolate the power, adequate drivers for the blubs, no flicker, and adequate cooling. Also my opinion of the right setup would make it look period-correct for the car. Overall, I believe the only real reason to consider LED is to provide more powerful light output for driving. There's no real power savings needed on a gas powered car unless maybe to support a lower rated alternator. In my case, I don't really need LED unless I just want to go down that path for fun. I also considered LED's for my Land Cruiser, because the light output is pretty weak. However, I also decided against it because I couldn't find many options that met my requirement above.

Without this the diode and alternator problems won't matter. No voltage, no charging. This can be checked with the alternator removed. Also, might as well check both pins. The top one should have battery voltage also.

Mechanic finally managed to get the 6 spark plugs working. All seem burning correctly with no fouling. Car does start misfiring if i turn the air conditioning on. Id like some advice on replacing the ac fan, condenser and compensator so i can have an efficient air conditioning system that cools well and does not make the needle move to 3/4. We are getting there!

Also, Japanese market variants had the option of factory stereo from beginning of production, so there are speaker holes in both sides of the interior quarter panel trims and the sheetmetal underneath them was designed to accept speaker mounts on both sides.

😎

Never seen the last type. Suspect it is a retro fit that someone did from some other car. The first one is 240, second is 280, though can’t nail down the change over date. Could be as early as the north american 260 in 74. The fiche might provide the date info

(this is for anyone else interested in a little information about some specifics that you raise:) 1. NONE of the above are "Coil - ". (Stock config = Coil "-" is connected to the points output of the distributor. So, new wire from the Coil "-" to your new gauge...(it will be a 2nd wire connection as the Coil "-" needs a "signal to fire" from points or an electronic ignition unit as well - your new gauge is just tapping into that signal)) 2. You don't necessarily need to jumper any of the wires in that connector, but you need to understand the coil wiring to decide whether to JUMP or just ABANDON the G/W and B/W in the connector pictured above. The stock circuit goes like this: IGN SWITCH -> B/W -> Ballast Resistor -> G/W -> Tach connector -> Loop on back of Tach -> Tach connector -> B/W -> Coil "+". The coil gets power at IGN ON through this and the Tach "senses" the flow of electricity to the coil. If you're replacing the stock Tach, the re-route of the B/W back to the Tach is not necessary - the B/W and G/W to that connector can simply be ignored (abandoned). SO - the B/W that goes to the Ballast can be connected to the Coil "+" - either through the Ballast (by removing the G/W and running a short wire from there to the Coil "+") OR bypassing the Ballast and connecting the "ballast's" B/W directly to the Coil "+" instead - IF you no longer need a Ballast Resistor in the circuit. note: I think it's better to abandon and get all that extra wire (and added resistance) OUT of the power circuit to the coil... BTW, the other two wires in that connector: Black - is a Battery Ground. R/L is gauge lighting - it's listed in the wiring schematic as "IL". So Black is the power ground for the Tach - the Tach gets power (battery voltage) from a Green in another connector.

Awesome.

Contact Oliver at Zspecialties to see if he has any. https://zspecialties.com/ I suggest calling him at the number at that website. Over at zcar.com, his user name is zmanofwashington.

Another component bites the dust, opened up my fuel pump relay only to find a similar fate as the ignition module. Weird part is, the relay looked like it might have been taken apart once already, but the guts say otherwise. I wonder if all the relays on the passenger side will be like this also. I pulled this link from a post I found here and ordered one. And I also pulled the color wiring diagram from here and had the local printer blow it up. Now I can actually read it.

1977 280z AFM from an EFI engine. Car had been sitting, everything looks in working order. asking $150 obo. located in Gilbert AZ

I worked on the heat shield/ cable bracket some more today. Here is the current pattern An earlier template on a piece of coil metal I glued it to piece of 16ga I had laying around A little cutting We will have to clearance it around some of the header pipes. Since it's an equal length header, they intrude on the carb area more than some We will use some stainless exhaust tube to deal with the clearanced areas. Once I finalize a design I will have sendcutsend fabricate it for me

I also got the tool covers from resurrected classics and got them installed A little nerve racking to bend the plastic hinges to mount them

Planning to swap an R200 into my Series 1 car (12/70 build date) and am looking for the mustache bar, front diff mount and insulator and the rear transverse link mount from a later 280Z that came with the R200.

Sent PM

Awe man this is a trap!

S30 parts are rare and expensive. Not enough competition or volume of sales to keep the price down.

This is the other name and email used during the email communications with Sully. Phaedra Rosengarth armychick44@hotmail.com He sent several pictures of the new tank and a few pictures of a partially restored tank that he allegedly was working on.

@Mike

For sale are 3 280zx gauge clusters (without clocks). One is for a right hand drive. I make no claim as to the function of the 2 gauges per cluster, but they should be good. Asking $15 plus shipping If interested contact me @ ron@zclocks.com

This bot is not like the others. The link actually leads to a real business. In Dubai.

Roof in really nice shape….a surprise. Frame rails, outer rockers and floors toast ….not a surprise. Firewall, spare tire well and inner fenders are nice..surprise. Tunnel and inner rocker area in great shape, perfect to attach new floors. Have rails, need both floors. I’ve seen gnose cars trim lips off the rear to allow wider/lower tires/suspension. Debating on leaving them trimmed off, or replace entire rear quarters to have the complete outer rear well.

The first picture from the left shows a completed repaired hi- lo beam switch circuit board repair. The next 2 pictures show continuity on both of the hi- lo beam switch closed circuits. In the mail on the way I have a parts turn signal switch with broken hi- lo beam switch circuit board. In the near future I can detail my repair protocol if there is interest out in Datsunland.