Topics Last Week

I'm in the process of rebuilding the front suspension on a 1971 240Z. I've noticed the coil spring lengths are not the same they're off by 1/2 to 5/8 of an inch regardless of where I measure one of is shorter. Do I need to be concerned about this point? If this is an issue what should I purchase? Thanks In advance.

Too many projects are IMG_2691.movIMG_2691.movdelaying this RHD hs30… Heading to the wetblasting area to determine if anything is left to work with……

Been a while since showing 2446 bones…and she got good bones. Slowly finding time and discipline to prioritize some shop time. It is fun putting a few peices on the rear, dash will be coming out to recover. Had been a while since I have inverted to disconnect heater control cables….throttle lever cable at top of the gas pedal assembly…etc. rear panel is too dark, debating to reshoot to lighter shade….

Quite true, thanks.

Turbo, Julio. You can do just as well with that P90 head and flat tops on that F54 block. I know you've read this before but I'm gonna post it anyway. https://datsunzgarage.us/engine/

Yes, the plan is to paint the airdam too. Hopefully it will stick...

I did the yellow/blue wire grounding test. I had both the Floor Temp and Fuel warning lights on. I guess I have an independent to the fuel sender's thermistor issue with the Floor Temp sensor. I will check the relay under the pass seat.

I dont believe the 510 has a rheostat

My new check valve came in today so I will be seeing how it performs on the car compared to the one I have currently. I suspect it will be identical, but we will see. I was walking the dog the other morning and a thought came to my mind. My brake pedal has great initial bite, but then goes hard as a rock, with no give in the pedal. I also recalled that while the car is in neutral, I cannot roll it. At all. Takes every ounce of strength to push it. When all parts were more 'fresh', I could push it up and down the garage with relative ease with one hand. Just to further flush this out, I am jacked up both sides by the diff adn wanted to see if I could spin the rear tires with the car in neutral. NADA. Drums are darn near seizing up the rear end. How long has this been going on? Not sure, I drove it around town about a month ago. No issues, but again, car did not want to roll without engine help. I now suspect something is amiss with the wheel cylinders / emergency brake adjustment. Perhaps a complete brake overhaul is not needed. Maybe just a refresh of the rear and some better pads would do on all four corners. I think rear disks would be a worthy upgrade. Anybody running around with just a rear disk brake swap.

I am near Canada:)

$840 (plus shipping) at Motorsport Auto.

And a white picket fence… so American!

I appreciate the clarification. The articles I read did not provide that information.

I wasn't there when they made the exhaust manifolds, but my assumption would be the same. I would expect they were raw uncoated cast iron. Maybe a thin coat of oil so they didn't flash rust in the parts bin, but that would burn off in the first few minutes of engine running.

Glad to help. Hope you make good progress and get things working well soon!

I stole this cassette from my step-a s s hole when I was a kid. When cassettes where still off white colored, before the clear ones. I listened to it so much I still know every word to all the songs but this was my favorite.

It doesn’t seem to be.

http://www.zcarblog.com/wp-content/uploads/2022/11/IMG_3902-1024x768.jpeg Happy 89th Birthday to our hero Peter Brock! You have been and continue to be inspirational to us Datsun fans worldwide. Here are a few pictures we enjoyed taking with you over the years: http://www.zcarblog.com/wp-content/uploads/2022/11/unnamed-1-1024x768.jpeghttp://www.zcarblog.com/wp-content/uploads/2021/11/DSC05510-1-e1637002594621-1024x1006.jpeg http://www.zcarblog.com/wp-content/uploads/2016/11/lagunaseca2004153-400x300.jpghttp://www.zcarblog.com/wp-content/uploads/2022/11/IMG_2311-1024x768.jpeghttp://www.zcarblog.com/wp-content/uploads/2021/11/IMG_9747-1024x768.jpeg http://www.zcarblog.com/wp-content/uploads/2022/11/sema-1024x1024.jpghttp://www.zcarblog.com/wp-content/uploads/2022/11/275435624_5253829184651694_278823018715978593_n.jpeghttp://www.zcarblog.com/wp-content/uploads/2024/11/314962664_499938492181328_4586337483149355287_n.jpg http://www.zcarblog.com/wp-content/uploads/2024/11/312177026_483959523779225_1687953212474383395_n.jpg http://www.zcarblog.com/wp-content/uploads/2024/11/382583804_692126209629221_266883468108368867_n.jpg View the full article

$36,000

Thank you, Buddy.

Hi Bob: If you are still looking for a welder I would recommend Elhot Metal Fabrication. He is working inhouse at the Shop club on 6th Ave S. He has done rust repair on 3 of my cars over the last 20 years and he is top notch. Of course with 30 years of experience, he's not cheap. Cheers, Mark G

Update. It's been several months when I posted questions about a soft feeling brake pedal in my 79 zx. I checked the vacuun check valve and found it to be defective. I didn't even use my vacuum test equipment but instead just removed it and blew and sucked through it and knew it wasn't holding vacuum. I replaced it and now have very good, stock brakes again.

Yes, take it a lock smith. If the core can be removed from the cylinder it isn't that difficult to make a key. Key blanks are common. I can't recall if the core is wafers or pins. Come to think of it, it's a double cut key, so it would be a wafer lock. To remove the core from the cylinder without a key, not a big deal to pick the lock. I have no idea what a lock smith would charge, but it's not a big deal. When I closed my business I kept all the key blanks, I probably have what you need. Jim

This was a clue that it was an electrical problem. If the engine was still spinning because it was in gear then spark will still move the tachometer needle.

I think you may find @26th-Z and @Carl Beck already have most if not all of the documents. I've hoovered them up for my archive. Will be interesting to see what if goes for this time, I think it sold at least once or maybe twice since the last BAT appearance 6 years ago.