Topics Last Week

Good question. I 've used it several times over the past decades and used it again on my 79 last year but I doubt that I'll be around in 20 years to confirm.

I just saw at 1982 280ZX list on Facebook Marketplace near me.

Yesterday, I made a 4-hour "tour de Suisse" to collect various parts which I've purchased and visit some friends. My first stop was at my good friend Stefan from Cagedude. Aside from always finding crazy builds in his workshop, I'm always full of joy to see his collection of C10 and C110 Skylines in various states of Restauration. The red one in front is a genuine Swiss-Market 2000GT Shortly after I got my tool-wall, another original Datsun workshop tool wall popped up for sale. Since I already had one, I told hem he should get it, which he did. The wall stayed in his possession for a while, but then he called me and told me he has no time to complete it, so I should get it instead. So I picked it up yesterday. So it means the hunt for all the missing tools starts again. Luckily, I already was able to complete an empty wall once, so I hope I'll manage that again. Oh, and I also picked up this 280ZX T-top Nissan Press poster for another friend of mine. The second stop was at my mate Heiko, who has a nice collection of Z's and roadsters, among some other cars. The reason was to pick up a complete euro-spec rear bumper center section, which is increasingly hard to find. The EU-version has additional holes for the lower number plate lighting. I have several, but all have messed up mounting brackets. This one needs some love too, but at least the brackets are good, so I can use it for test-fitment of everything. And then i got another "Mystery package" from a long-standing parts dealer partner, which included various interior and battery parts. Plus a rear bumper side section, ashtray, etc. And some random NOS parts, plus a lot of replated parts. It's always a bit of a mixed bag from this vendor. Some parts are really useful, NOS or good quality, Some appear to be from different generation Z's or even other cars, or are not in the best condition. Usually, the good parts make up for the bad ones. This-time the J-bolts for the tank straps came in very handy, and it's always good to have a variety of parts on site. Even the "bad" ones usually get used for trial-fitments, etc. I hope with all this new parts and information from yesterday, i will be able to spend another few hours in the workshop with hopefully some progress on the car. Stay tuned.

Nice, people can always PM me for it at €300,- (It's a clean unscratched clock the last time i checked, if not it will be less offcourse. And i send pics before selling.)

@Mike

Those are some cool turnbuckles with the moe clamp ends!

Mine was clearly an adhesive failure and not a cohesive one. I suspect folks who have cars that have been out in the summer sun for many years might have the cohesive failure you experienced.

This is how the msd blaster 2 got wired to the tach, distributor and ballast. Hope im not missing anything. Tach is working but plug 4 is still getting fouled at idle.

The company known as SPAL no longer sells trinkets like the units you and Dave Irwin used back then. But the current units - there appear to be two basic designs, what I call the "separated drive system" like you, Dave and I have and the "combined drive system" where there is only one connector between the drive motor and the actuator that goes on the door handle spline shaft. You pay your money and you take your choice.

I have rebuilt circuit boards for the 75-78 280 OEM clocks and single knob RC (calendar clock) . Your core circuit board is required and the cost is $78 plus shipping and taxes . If you are interested or have questions please contact me, ron@zclocks.com Thanks for looking

I've read that the mixture screws raise or lower the nozzles 1mm per revolution. One can raise the nozzles to the top and lower them 10 turns. At ten turns, the fuel level should be near the top of the nozzles.

Cliff, you can buy a lot of Powerball tickets for $12,000 😎.

I really needed one more week to work on the OG before I left for Zcon. Just one more week would have made the whole drive so much less stressful. I would have known that I had a radiator problem and I would have mitigated it before I left. But I lost that week waiting for struts because Amazon screwed up. So here's where I am today. I took the leaky radiator I got at the show to a local radiator shop. They sealed up the leaks and pressure tested it. I swapped it into the car, and.... Driving around with no thermostat, it wouldn't even reach proper temperature!! Way better than what was in there! So just to see where the gauge would land, I put a 160 degree thermostat and went for a drive. It stabilized about here: So next chance I get, I will swap out the 160 for a 180 thermostat and check again to see where the gauge lands. But the bottom line is I'm a whole lot better off than I was with the previous radiator! I blame Amazon. And photobucket.

Worked for Grannyknot using zero-forgiveness sheet metal. I don't see the problem.

They wrote great songs but I can't think of any covers that were done. What a shame.

Here's a very familiar picture, I'm pretty sure Zkars put up for us, that shows where the fluid should be. The top of the rectangle.

As long as we’ve brought up our daily drivers, every time I go to the Toyota dealership they were telling how much mine was worth and how I should trade it! I double crossed them and sold it to a private party for $36K and bought this! Holy Schmidt it’s fast for an SUV. Porsche Macan GTS. That’s one of the other three Porsches sticking its tail out of the garage behind it…

Arguably the rarest of the fairladies…..

I'm going to want power windows at some point, but would like a fairly invisible system. Atleast on the door card... I'll keep an eye out for your thread

Is it for the 260 in your cars owned or is it a ZX as the TECH FORUM category you chose? Here's wiring for a 260. There's a lot of info in the RESOURCES category up top of the home page

The RPMs should decease when lifting that piston, almost dying out. Lifting the piston disables that carb then you are running on the 3 cylinders the other carb feeds. That's what mine does anyhow. Try reaching in and lift the piston itself instead of pushing those pins down. Your needle height may be off from the rebuild with the needle height set screw? Remember raising and lowering is viewed from the bottom of the car. Turn the nuts towards the fender to lower the needles. Read the section on SETTING MIXTURE.

Still in original packaging. $10.

Phot says it all. Sand, paint and ready-to-go $25

I just this morning realized my '72 has all Nissan glass except the front, PPG. That means it's not 100% but a busted windshield on a 53 year old car isn't a deal breaker. It does have the blue-ish tint sun visor.

Glad you came to ZCON and gave me some inspiration on my future engine! I got a pic of our cars together and one of yours at the show Saturday. Hope to see you again at a future event!