Captain Obvious

Glad to help. Hope you figure out what's going on. And thanks for highlighting a year related issue with the FI Bible. I never looked into it that deep and didn't know there were surprises like that in there. That could potentially save some other 77-78 owners major confusion in the future now that we're aware of that shortcoming. FYI, there is a later version of the FI Bible from 1980. It suggests grounding the negative side of the coil and doesn't talk about that single wire connector at all. Despite that, I still like the earlier version better than the 1980 version.

Man... That was confusing, but I think I figured it out. First, the simple (Obvious) answer... If you look at the prior page (32) of the FI bible, they show you how to locate the "ignition lead wire" and there is even a picture to show you what they are talking about. What they want you to do is disconnect and re-connect the wire that goes to pin 1 of the ECU, and the way they suggest to do that is to make and break the single wire connector under the dash next to your fuel injection relay above the driver's knee. But here's the rub..... You don't HAVE that single wire connector. You see, what happened is that the FI Bible was written in 1975, and hence, it referenced the 75 design and documentation, and in 1975 (and 76) there WAS a single wire connector there. But by the time they got to your (and mine) 77, they did away with that separate single wire connector and ran all those wires (including the input trigger signal) through the same connector that mates to the under dash harness. You do not have a single pin connector that funnels the ignition lead signal from the firewall under-dash harness to the FI system. That whole part of the FI bible does not easily apply to 77. All that said... What they want you to do is make and break the connection to pin 1 of the ECU (which is the ignition input signal). Easier to do in 75 or 76 than in 77. So here's what I would do instead: Pull the center high voltage wire out of the distributor and place it close to a good ground like the intake manifold or strut tower nut. Leave the other end of that coil wire connected to the coil as normal. Turn the key ON. Connect one side of a piece of test wire to ground. Ground and unground the negative side of the coil a bunch of times. You should get a spark from the coil wire to ground every time you unground the coil negative, and you should get an injector click on every third.

Man... I am IMPRESSED!! Now mind meld your way over here and fix my engine.

I doubt there is any easy answer. Probably a bunch of small vacuum leaks spread out all over the system. How long are you planning to keep these carbs in service before the RB swap?

Johnny, As eluded to above... If you're running carbs, there's no effect when you remove the oil cap when the engine is running. That's only an issue for the fuel injected cars. Carbs could care less.

Haha!! I could possibly be convinced to make more. You know they aren't metric though, right?

Never underestimate the rust of the dark side.

Yeah, I'd avoid the spoons too. From what I've heard, they can make you fat.

They don't filter for squat either. What he said.

Mark, I wouldn't pull the carbs apart to get the old oil out. I just roll paper towels into a narrow cylinder and stick them down into the damper hole to soak up the old oil. Give it a few minutes to sop up the oil and then pull the paper out. Takes two or three rounds of paper wads to get the old stuff out. Taking the pistons out and turning them over to dump the oil out certainly works, but I consider it a risky maneuver with very little gain over just keeping them together and sponging it out instead. Respectively submitted, of course.

So do you think this is an issue on ALL of the carbed Z cars, or is this something specific to yours?

He also said "A man's got to know his limitations."

Looks great. Can't wait hear how it runs!

Like Ricky "Wild Thing" Vaughn.

Back when I started my degree, they gave the orientation speech... "Shake hands with the students to your right and your left. Because many of those students won't be here come graduation day." As I shook those hands, I was pretty much 100% positive that I was the one that wouldn't make it. What a surprise...

Excellent! Congrats to all involved!!

Wow. Looks fantastic!!

The video worked OK for me. Cool video. After you fix your rev counter, can you post the next video both in slo-mo and at regular speed with sound? Would be cool to seem them both and might help figure out what's going on.

How about a couple pics of the wavy washers? That would add a lot to the discussion.

Glad you are able to focus now. Life gets in the way whether you really "let it" or not. I'm just back on the radar a couple days ago after a sports injury.

Somewhere I think I read that it was Time to refocus on your Zs. That was about three years ago?

Wow. Lot of changes from that unit to 77. My 77 only has one electrolytic cap. Everything else is film.

I've never vulcanized rubber. Anyone here done that? Is raw un-vulcanized rubber easily available?

Nice pics. Now you just need a set of these. If I remembered your mailing address....... I was only there once. :

The bling is unbelievable!!