SteveJ

Actually if it is carboned up, it would be dropping the amount of current flowing through the fuse as it would be acting as a load in series with the lights. So we can solve for the nominal resistance of the bulbs, add some resistance in the circuit for the switch (0.5 ohms), and see what the circuit current would be. So the current through that fuse would drop by over 3A. The switch would still be a hot spot, but it should not affect the fuse box.

I still have a VDO PM9196 in the box. If I can remember, I'll take photos and measurements, too. The only trimming I saw that may be necessary would be for the brackets for the mounting screws. The VDO went right in.

The strange thing is that I didn't trim anything for it to work on my 240Z. You may want to see if you can swap the squirrel cages between the fan motors.

What part is larger? Are you talking about the squirrel cage?

I've never taken thermal readings, but less current flow results in less heat. I have not seen signs of overheating in the parking light circuit in my 260Z since I changed to LEDs 12 years ago.

The contact that is at the point of melting is the load side of the fuse. The line side has enough copper to spread the heat out. I know I posted in the past about the amount of current that runs through this circuit. I'll put it out there again. The design of this circuit is marginal. Using the specified bulbs, this is approximately what the current is in the circuit with incandescent bulbs at 12VDC. The circuit is rated at 20A, so the fuse is fine, but if a previous/current owner used the wrong bulbs in the side markers (either to make the car more visible or due to ignorance), the current goes up quite a bit. This is why I push for LED replacements. This goes double for owners of 73-76 cars as they use a smaller connector at the steering column, and I've seen that connector burned up too many times. After replacing the bulbs with LEDs, the fuse should be downrated to 10A. I can get the current down to around 3A or less on my cars with LEDs for all the marker and gauges lights.

Still, that's good to know about the risk of "discounted pricing" at Amazon. Thanks.

What meter did you purchase? You might help someone avoid the same problem.

Rockauto is cheaper, even when you take shipping into account. Also, you can always search for a 5% discount code for RA. https://www.rockauto.com/en/moreinfo.php?pk=488596&cc=1209260&pt=4588&jsn=837

RW - High RY - Low The switch is a toggle switch. Every time you pull it back all the way, it toggles between the high and low.

I'm not going to verify my sanity nor anyone else's. This may help explain the erratic behavior. From the EE section of the FSM: (Note what it says about the dual points.) So when the engine comes up to temperature, the timing is retarded for the automatic transmissions. Here's how it looks in the wiring diagram: As @Yarb said, use one set of points. Tune to that. Be happy.

So, to get this back on track, here is the video I was promising.

Well, if I have enough time today, I'll finish editing and post the video.

Bring them down here. We can drill, heat and extract.

You may want to search around Hybridz.org to see if any of your questions can be answered there.

So, for the rest of the relay panel, the bottom relay is called the AC relay sometimes and Accessory relay other times. It does provide power to the AC systems when they are present. In the 73, you can trace the wire downstream to the blower motor. For whatever reason, the horn relay and defogger relay have been swapped on your car. I can't tell you why. Relay 5 is a little confusing. In the 75 wiring diagram, you can find artifacts of the seat belt interlock relay that was yanked before the car went into production. In the 76 wiring diagram it looks like relay 5 is for the seat belt warning relay. The BY wire is energized only when the car is starting, so I would assume that the is coil wire. (Hint, measure resistance between the BY and B wires on the relay side. The coil will have a resistance reading. It's like measuring resistance between the 85 & 86 pins on a Bosch relay.)

The diagram showing 10 pins used is wrong. I believe I addressed most if not all of this in your thread on the wipers. Note that two of the terminals are repeated, B & E. B = battery & E = earth/ground. You don't need two power or two ground wires. The 73 wiring diagram shows 9 pins, so I'll use that to explain. P = Park M = Motor 3 = High E = earth/ground B = Battery I = Intermittent W = Washer 2 = High 2 = Low Notice that the 3 isn't shown on this diagram and is also unused on the 75. Oops, I made an error. The 75 wiring diagram shows the 7 terminals being used. I think I made the right corrections above. The weather is cooling off soon, so I may be in the garage more in the near future. I can do some testing I've been wanting to do.

I checked all of the part numbers listed for the wipers on carpartsmanual.com against courtesyparts.com. All that @Patcon might need are NLA.

As @zclocks said, you need a meter that can read capacitance. I prefer to use my Fluke for that. However, if you don't want to spend $200 for a Fluke, you can always try a cheaper alternative like this: https://www.amazon.com/AstroAI-Multimeter-Ohmmeter-Voltmeter-Non-Contact/dp/B0842HTN8C It's just as easy as putting the meter on the capacitance setting and touching the leads to the two wires on the capacitor. By the way, having a capacitance meter can be handy for testing your home AC. I've used it to find a dead run capacitor for both of my units and a friend's unit. Having a good meter saved me a few hundred in service calls.

I guess she didn't.

I actually consider it a fortunate mistake because it gave me a better understanding of how the horns work.

So last night I wanted to see if I could improve the sound from the horns @Tirnipgreen asked me to work on. One was nice and strong. I wasn't going to mess with success. The other wasn't working, though it worked before. I could tell it was pulling in the diaphragm, but the contacts weren't opening. This was verified by taking current measurements on that horn and one that worked. The non-working horn was pulling a lot more current. I tweaked on the parts repeatedly, but I couldn't figure out why that one horn would not work. Finally out of frustration, I took the other horn apart to compare the diaphragms. The problem then stuck out like a sore thumb. Whoever reassembled the diaphragm on the horns didn't put the parts back together in the right order on the non-working horn. The fiber washer was on the wrong side of the bar between the diaphragm and the bar. This is how is should be. So when the diaphragm tried to open the contacts, it was still providing a path to ground for the coil. With the coil still energized, the diaphragm wasn't moving. Once the diaphragm was assembled properly, the horn worked just fine. With the new knowledge, I decided to re-shoot the video to go over the details of the horn. I just have to edit the new video.

https://www.summitracing.com/parts/ear-510erl/make/nissan/model/280z

I got @Tirnipgreen's horns working and got an old pair of horns from my 260Z working, too. I posted information here: I did shoot some video that I need to see about editing into a YouTube video.