Patcon

That sounds right. I parted one a few years ago.

The wire speed might be a little bit high, but it prevents burn back like that. The gas was on but when the primer burns it makes it look like that. That was a half dozen quick welds. One time I burned through it. I had to keep moving the voltage around depending on where on the edge I was welding. I really just wanted to add enough to then knock it down. So I stacked it in different ways until there was enough there.

What did you buy for a sewing machine? What are you using as a pencil on the fabric?

Wow! Those don't look too good. Is that just a rusty glob or something else? It looks like the lense is cracked and all gobbed up

It already is. It's amazing how fast flat surfaces in my shop accumulate stuff!

I am in the midst of blocking the whole car and doing the fine filler work. There is always another spot you missed. I am still waiting on my Australian help to arrive! I also had a problem spot on one side of my hood. My hood is a 25 year old after market hood so it has some issues. One was at the upper left corner, it turned in significantly and showed badly against the inspection door. So I added to the edge with the welder. It wouldn't looked so bad if I had stripped the primer back further Shaped it down A little short strand fiberglass to seal it up. It might need a touch of filler, but it is much straighter

I ordered these screws for the turn signal lenses Here is the finished repair on the one signal body The screws had a small plastic washer on them. I thought I would use a small rubber O ring unless there is a better idea

I lifted these up some on 2x6's and built a top over Thanksgiving

I believe these are off a 280zx. Free for shipping, otherwise they are going away.

Perfect, thanks. They look really nice like that.

Thanks What high temp clear did you use?

What was the refinishing process for the front calipers?

I don't agree with your assertion, and I was going to write a rebuttal to your post. After having thought about it, I am not going to provide a rebuttal. As I doubt, I will change your mind and you haven't changed mine. It seems like a poor use of time to try. As well as the obvious thread jack it would be. My apologies to @7tooZ for the distraction.

Adhesion should be fine. Skip the epoxy

What is the air dam? It's interesting looking.

I don't know why you couldn't go right over it with color, now that it's knocked down to 400. I think the recoat window refers to running color over color with no sanding in between.

Yes what she said. Roll the car part way out, then pull the drive train. Rearrange and roll the car back in.

Dude!!!! That is super cool.

Truth is independent of perspective. Everything else is opinion, there is only one truth.

Actually the ECU relies on each O2 sensor independently. They are used as much to determine faults and OBD codes as real time fueling. They are also used to cross check each other. Not so much for accuracy but for function. I have found that when it an O2 sensor fails it's dead, not out of spec. So if my wideband O2 fails which it has in the past I get no AFR readings.

I totally understand. I think a lot of that is just experience. Both with stacking paint and knowing how much paint you've taken off. I am not sure any of us will ever paint enough cars to get to the level of experience where wet sanding is second nature and care free.

Your second cut looks much better. Wheee! is right sand then check, then sand some more. After a while you can tell by how your sanded panel looks if you have it smooth enough. It looks like guide coating does. There will be tiny round spots that are not the whitish color that the high spots are. When those are pretty much all gone then it's ready to cut & polish. You can use wax & grease remover to wipe down the panel and it flashes off quickly.

If this is directed at me, I have not run into anyone making them. If I need them I would make them in the bench vise. The new fabricated ones from the earlier pictures have a weld seam down the sides. So you can fold them all up and then weld down the side. That is what I would do if I needed some. Make a stiff paper template first to pattern from

I like the looks of the pan. I don't know if it's in my immediate plans right now.

But a good first post!