Zed Head
Community Member
-
Joined
-
Last visited
Everything posted by Zed Head
-
Seems feasible. A picture of a removed bell housing would be interesting.
-
Must not be much current. It will kill the battery but the circuit has enough resistance that there's not enough current for a test lamp? Seems odd. How fast does it die? Has the alternator been converted to the internally regulated type? There is a problem with some of the conversion procedures that are out there on the internet.
-
-
"I have the fuel rail removed right now with everything else connected and I'm going to switch the key just so it starts priming, got the idea from Dave WM. " That's a good idea. Is the CSV out too? Watch all seven. There's no prime pulse on 1981 I think. That came later and even then it often doesn't work. Disconnect the starter solenoid wire, and turn the key to Start. The engine won't turn but the pump will get power.
-
The injectors get power as soon as you turn the key On. So any short to ground on the wires going back to the ECU would open them. A pinched or abraded wire for example. But a short should show up in your testing at the ECU, as a voltage drop, less than battery voltage measured at the injector pins. You might also hear them click when your turn the key on although the BCDD clicks also. The CSV should only get power when the key is at Start. So it's possible that it would flood the engine, but the odds of pumping a quart of gas in to the engine through shorted injectors, by sitting with the key On, thinking, seems more likely. I filled a chevy crankcase with gasoline after I put a friend's carb on the car and tried to start it. Turns out he had got it from someone else and they had removed the float valve.
-
Before you button it up, just rotate each lobe to the base circle (the part where there's no lifting force on the rcoker arm) and measure lash. No need to turn any wrenches, just get a number. That will tell you a lot. If you had excess wear you'd be able to feel it on the lobe, by running a finger nail across the lobe and feeling for a ridge. The deeper the worser. There's two easy things that will give you something to ponder over the cold weather. grannyknot mentioned rings. If you re-run your pressure measurements, but with oil in the cylinders, that will give an indication of rings versus valves. Oil tends to affect the rings sealing more than the valves.
-
Might be flooding due to disconnected or broken coolant temperature sensor. And somebody parked it beside the barn for a reason. The 1980 EFI Manual is probably about the same for 1981. Might use it to at least get familiar with the parts. http://www.classiczcars.com/files/category/14-280zx/ http://www.classiczcars.com/files/category/4-manuals/ 1980 "EFI Book"
-
That was my conclusion too. You can see the reverse lockout mechanism inside.
-
I'll put the pictures here. More interesting. It's from a mystery 5 speed that Itook a chance on. Ended up using the case to build a 71C swap. The insides had broken synchros and the adapter plate bearing was bad. Looked like somebody got angry and tried to blow it up. But the cases were in good shape.
-
Sounds like it's running very lean. You probably have a leak in to the crankcase from one of the PCV hoses. Examine all of them, including the one in to the block under the intake manifold. Make sure all of the hoses in this picture actually go somewhere important. All of the air that goes in to the intake manifold needs to go through the AFM. So check the hoses from the AFM to the manifold also. If you can, confirm that your fuel pressure is correct also. Pumps get noisy when they have to push hard through something like a kinked line or blocked filter, or when they have to pull the fuel against a restriction. You could have fuel starvation.
-
Hope I wasn't too blunt earlier. The clutch control is actually very simple once you dig in to it. The reason that the same measurement works for all combinations of engine, clutch and transmission is because the slave cylinder bolts to the tranmssion in the smae spot on all transmissions, and the fork pivot is the same height, and the flywheel surface is usually the same distance from the mating surface of engine and transmission. Here's a diagram from the 1972 FSM showing the relationship of all of the parts, with the adjustable rod. You can see how the angle of the fork needs to be the same (edit - unless you have the adjustable rod. But Nissan got rid of that, probably to hold the best angle for the slave cylinder travel) because the slave cylinder and fork pivot can't move. They're fixed. So the fork at the collar is always starting in the same spot. so you have to adjust the collar to make everything work right. It's all about where the end of the fork starts its movement. p.s. Found that the new software allows CTRL V pasting of snipped images right in to the post. Sweet.
-
The oil from the oiler also oils the valve stems and their seals, and some slips past for the guides. Oil draining and flying everywhere when it works right. When a piece of the system fell off the rest of the holes didn't get any pressure. The front cylinders might have got some timing chain sprocket and chain splash, while the back was drier. I'm just conjecturing. I'd guess things got dry, some valve stems and guides and cam lobes and rocker arms got very hot, and this affected the seals and the valves themselves. Basically most of the valve train overheated. Might also be that there was some lobe wear and the valves aren't opening at the correct time. #4 might be dying. Did you check valve lash when you replaced the oiler section? Just one possibility.
-
If it doesn't keep rising, past the M, on th highway, you don't really have a problem. Ranges have a high and a low.
-
We already said that your measurements look right. Confirm that the hydraulics do what they're supposed to do. Measure the distance that the slave cylinder extends out of its bore when the pedal is pushed. Hydraulics can fool a person.
-
Nobody mentioned diameter. Maybe "thickness" is a better word. Stole this from EuroDat's past post. Post #33.
-
That would be the pinion shaft flange. There are different styles out there. Beware. Specify the drive (propeller shaft) that you'll be using. The Z's up through the 280ZX's all used the same bolt pattern and bolt size, except for 1975. Might be easiest just to get an old open 240 - 280Z open diff (except 1975) and steal the pinion flange.
-
I have a complete 240Z driveshaft. Two actually. Both the short style though, for the offset diff. But the flange would be removable.
-
Just noticed that Patcon has some nice parts for sale. A very nice looking shift knob, if you want something that looks good. Mine are still available, just saying.
-
PM me an address and I'll see what the charge is. Looks like CO might have another source. Winorama.
-
I have one. Should work. PM me and address and I'll see what shipping costs.
-
Here's the two. One is a 75/76 unit that I picked up for cheap, A31-060 001, and the other came on my 1978 parts car. A31-604 000. It has a working fuel pump contact though, so I used it on my 76 for a while. They both work, with the tweak, so you'll have to overcome the quease of destroying a working part. Or just put it back together when you're done. They both have the backfire valve in the vane.
-
I think I kept those. Out there somewhere, I'll look. That's a USPS flat rate part, I think. I'm not a big shipper so if somebody knows the cheap ways, chime in.
-
I would second that, IF he was measuring across the switch. Unclear what he measured.
-
-
There are two sides - one to the lights and their ground point, and the other from the power source, You only reported one number. Break out that circuit testing knowledge. This is a very simple one, power on one side and device on the other. It's just a switch, a break in the circuit. Button in, circuit made, button out, circuit broken.
