Zed Head

Here is a bolt on for Porsche 930 style CV axles https://zcardepot.com/collections/rear-axle-and-differential/products/billet-aluminum-cv-axle-adaptor-930-240z-260z-280z

Here Here's a weld-on conversion for the 300ZX CV axles. https://zcardepot.com/products/cv-axle-conversion-kit-r200-240z-260z-280z

I've only seen weld-on CV conversions that were any good. And that's for bolting them to the wheel-side axle. R200's are all clip-in on the diff side. The clip is either on the axle or in the diff, but they work the same way. No offense but you're asking questions that can't be answered because that's not how the R200 works. Did you look in the hole yet, for the clips? Your diffs are probably essentially identical. You can also pop the axles out of the one diff and try them in the other. Use a chisel or big screwdriver to pop them out.

You're right, I screwed that up. I even spent some time looking around to make sure it was right and it still wasn't. I think I had CV axles and viscous and short nose all blended together in my head.

Ouch. You can move the crankshaft by putting the car in high gear and rolling it. Future reference...

You might be getting cam timing confused with ignition timing. It's a common misconception. You groove and notch have nothing to do with ignition timing. You should confirm that the ignition timing mark is at zero when the #1 piston is at TDC of the compression stroke. That's the starting point for ignition timing. Not uncommon for the marks on the damper to be in the wrong place. Could be a bad damper.

The aluminum bars are thicker than the steel Nissan bars. You probably just need new longer studs to do it "right". Here is Arizona Z Cars bar. http://www.arizonazcar.com/diffmount.html

what year is your car? The more details the better, In general.

Pictures would still be good. The washers in the picture I posted look flat. Is there a gap between the mustache bar and the diff when the front diff mount is bolted up? It would be goofy to keep making the bars if they're not right, then add washers to shim it. Maybe you got a mistake. You can remove the studs and get longer ones. I hate to say it again, but Whitehead's explanation is goofy. He could have made the bar to fit properly, "stress-free". Not sure what he's doing with his special washers. Includes WHP exclusive diff mounting washers to properly mount diff with no stress or tension on the Mustache Bar unlike other designs. Billet 6061 Aluminum – excellent strength Uses standard Urethane Mustache Bar Bushings in choice of black or red bushings WHP Mustache Bar comes pre-assembled with all hardware included (diff mounting nuts excepted) All hardware is either plated or stainless steel Includes WHP diff mounting washers Easily Installed and Removed Bolt-On solution for mounting an R200 diff Includes WHP diff mounting washers

There are two types of hole and two types of washer and two types of stud. Need details. https://whiteheadperformance.com/product/whp-billet-aluminum-r200-mustache-bar-datsun-240z-260z-280z/

Nissan went to the short nose R200 in 1985, when they went to the rounder 300ZX body shape. And the DAT-110-300ZX pattern shown in the picture was also used for one 280Z year, in the 1975 280Z. The fact that the axle shafts are gone could be for several reasons. Somebody could have taken them to use in a diff that came with CV half shafts. Look down the axle holes and see if the retainer circlips are inside. If they are it might be a 75 diff. If they aren't it's probably an 85 or beyond. They'll both work in your car but the one with the axle shafts is probably easiest to get in there. I don't think the ring set alone is really worth much, except as garage art.

Megasquirt and Haltech are popular. You're kind of starting at the end. Pick your engine management system and fit the parts to it.

Be careful with disconnecting your plug wires. And sparks in general. My experience has been that electronic ignition modules do not like stray electricity. I fried a GM HEI module by leaving two wires disconnected by accident. http://newautoaa.blogspot.com/p/secondary-circuit-of-ignition-system.html

"coil packs" usually refers to wasted spark systems. The LS engine coils are "coil on plug" or COP. www.hybridz.org has a bunch about them. @madkaw has commented about them. Wasn't that you that started a thread in the recent past about this?

The spark would have to pass through the cap material, or along the surface of the cap, to get from the electrodes to the outside. A thin layer of nail polish is not likely to stop that. Is there carbon tracking inside the cap? Follow the path of the spark from the coil's center electrode, through the wire to the cap's center electrode, and then through the "button" inside and out the rotor to each spark plug electrode. The lowest resistance path will be used by the electricity, of course. It seems like bad cap material just based on the video. There are conductive paths on the outside of the cap, probably on the inside too.

Nobody can say what's likely or unlikely these days. Not even worth trying to guess, just assume that somebody will suffer somewhere.

If you move the T/C rod through its normal motion while the suspension moves up and down you'll see that the rod pivots through the mounting hole where the bushings are. The end of the rod needs room to move up and down as the front of the rod moves. The PU bushings are solid and fill up the space that the rod end needs, putting a side load on the rod end. It fatigues and breaks off eventually. I think that it's also where the squeaking and groaning comes from.

Looks like a long lever arm. Interesting but potentially problematic. A broader view would be neat but if you want to keep it secret that's cool. Still, leave the engine alone and work on the back end, I'd say.

Your coil should be matched to the ignition module, or points. What are you using?

Does "position 5" mean 5 degrees advanced? Not sure what you're looking at or doing. Timing should be set at about 10 - 15 degrees advanced, normally.

I think that the mark is actually in between new and worn out enough to move. It's normal wear. If he move's it it will be too far advanced. It's on #1.

Who made it? Sounds like you're using the mustache bar and crossmember mounts. Four points of contact. Never heard of anybody doing this. Kind of on your own, except for general expertise here. Mounting holes, generally, are only used for the bolts to pass through, friction and clamping force should hold the metal in place. The hole edges should not see any side forces, in a good design. Still need a picture. Where's your phone?

He might have one of the aftermarket R230 mounts. Some of them have problems, it would be interesting to see it. If so, doing all of the realignment at the diff mount would be best, probably. The engines should be fine. If the engine is moved it will affect other things, like the throttle linkage, the shiftier angle., cooling fan orientation, etc.

The most common problem that I've seen is dirty/corroded battery connections. Clean them up and try again before buying anything.

You should have mentioned this from the beginning. Side to side, the engine is fine. Front to back is your concern and, as grannyknot said, your driveline angle is important, although it's not the driveshaft angle that matters the most. It's the match between the rear diff pinion shaft and the engine's crankshaft, they need to be parallel. You can jack the ends of the car up to get the oil to drain, if that's a problem. There are how-to's all over the internet. Here's some examples from the past. jmortenen's link to the hybriz site has a bunch, in detail. https://forums.hybridz.org/topic/43993-differential-laser-alignment-tool/