Topics Last 30 Days

1978 280z I want to replace my fusible link holder with a new blade fuse box. Many are listed on Amazon and the other sites. Any thoughts?

What is that, an ashtray?

They are not mismatched, they are identical parts, just one (right) is a complete zero hour rebuild. The front and rear Tokico's are very low mileage, I installed them shortly after I bought the car. The insulators are new. They were removed because the rebuilt one was leaking but I did not plan on having car off the road for months during peak driving season so I installed BC coilovers to keep the car on the road. I am less than satisfied with coilovers compared to gas pressurized Bilsteins, but I'll live. I put them up for sale on the off chance that someone might have project car that could use them, but eventually if they don't sell and i come across front and rear struts for the swap back (old struts were cut to accommodate coilovers), I will go back to Bilstein's and sell BC hardware. Below is car they are installed in (1972 240Z, Weber DCOE 40 six pack, recaro seats, roll bar, strut bars front and rear plus other mods. HTH, Willie

Does anyone have fastener specifications (size and grade)? Thanks, Keith

Pictures are available

I'm still waiting on a response as to why it's my fault that the door latch holes were in the wrong place and the door panel won't go over the ledge. I will say the door weatherstrips fit great and the rubber fuel filler neck fit perfectly so you do sell good parts. Just not these doors. Keep in mind I reverse engineer items and create foundry patterns based off of that gathered data. That is my business. I also reverse engineer fabricated items and make them into castable items. So when I say these doors have a problem and when I say your QC is nonexistent and when I say they aren't using welding fixtures to locate critical weld in place nuts and when I say they aren't using drilling fixtures for holes in critical areas you can take that to the bank. Because people pay me to do this. I just happen to have a Z car and I'm also a manufacturer of parts for these cars. Max you keep stating how many items you have sold as a baseline to the quality of the parts. I specifically said to you in our first conversation on the phone, how many of the 30 door sets that you sold are still sitting on someones shelf. Have you sent emails out to everyone who have purchased doors warning them of potential problems or are you just kicking the can down the road hoping for the best.

Same set up as used on the 510 wagon!

You are correct in using this product to seal affected areas but only after the rust has been treated. From the product description: APPLICATION - Remove grease, oil, and other foreign substances using POR-15 water-based Cleaner Degreaser followed with POR-15 Metal Prep to etch the surface and neutralize rust. Stir POR-15 Rust Preventive Coating thoroughly, DO NOT SHAKE. Always apply thin coats, minimum of two. May be recoated or top coated when dry to the touch, typically 2 to 5 hours. Topcoat when surface will have exposure to UV light.

Found it. SOB. It was with the extra freeze plugs I have. Fun times! Lol. Thank you for the replies. And yes, turning the pump CCW. Gonna shoot for having it all buttoned back up by Saturday. Wish me luck!

1970. Bring a TrailerL28-Powered, 24-Years-Owned 1970 Datsun 240Z Series I 5-S...Bid for the chance to own a L28-Powered, 24-Years-Owned 1970 Datsun 240Z Series I 5-Speed at auction with Bring a Trailer, the home of the best vintage and classic cars online. Lot #193,538.

I used a big flat head screwdriver and put the edge of the blade in the slots

Those look nice! Cost? Where to order?

On June 20-22, Classic Sports Racing Group (CSRG) will host the Corkscrew Classic vintage race at Laguna Seca. Z Car Garage will participate and support several client’s Datsun 510 race cars running in B-Sedan Group 3. It will be a great weekend filled with competition, camaraderie and plenty of Alfas, BMWs and Datsuns sharing the track. Remember to bring your family and friends as admission is FREE for spectators! http://www.zcarblog.com/wp-content/uploads/2025/05/19D723D0-B395-46AB-85CB-D50930271B88.jpg Hoosier Tire 2.5 Challenge http://www.zcarblog.com/wp-content/uploads/2025/05/SnapInsta.to_491443933_2755382734672778_1744548345452898412_n.jpg CSRG will be featuring the Hoosier 2.5 Challenge TA/BS. This is an action-packed race group with B-Sedans battling for points in the series! http://www.zcarblog.com/wp-content/uploads/2025/05/SnapInsta.to_475522665_898084419063046_5303664117389470980_n.jpg Watch these Datsuns Race! Want a glimpse of what it’s like to see Datsuns racing at Laguna Seca? Check out our 2024 race report with video and photos: HERE, and view a sample of cars expected to race June 20 at the Corkscrew Classic: Race car driver, restorer and Datsun Historian Glenn Chiou in his FAR Performance 240Z. This Z has a very rich racing history, driven in the 70’s by Loren St. Lawrence in VIPS Restaurant livery. http://www.zcarblog.com/wp-content/uploads/2024/06/Snapinsta.app_447213392_3677928062523087_8650031073483389271_n_1024.jpghttp://www.zcarblog.com/wp-content/uploads/2020/08/IMG_0595.jpeghttp://www.zcarblog.com/wp-content/uploads/2025/05/DSC1943.jpghttp://www.zcarblog.com/wp-content/uploads/2025/05/IMG_2733.jpghttp://www.zcarblog.com/wp-content/uploads/2024/10/IMG_2628.jpg View the full article

Opinions please! @zKars @grannyknot @Diseazd @madkaw @Mark Maras and all you other CZC's readers. I was thinking around $200 for the bare head? I found a P90 that pushed this E31 to the kid's table.

Richard, I have been using Vredestein Sprint Classic 175HR14 88H on my ‘71 series1 Z and they are pretty much a perfect size match to the Bridgestone Super Speed Radial - 20 original tires.

This is what is so fantastic about this site and the rare types of parts that are needed and pretty much unavailable to purchase new. Thanks to everyone for helping to keep these Ladies on the road!

What condition is your EFI harness? Have you replaced all of the connectors? I fought it forever. Finally reworked and soldered each connector, cleaned each contact and was amazed.

Update….. wound up stripping all the recently applied paint off 2446 due to ……well… a misunderstanding of the quality expected is a nice way to put it… New paint….better prep, better paint ….more controlled environment to apply has resulted in a more better virtually perfect paint reapplication. Have rebuilt, restored the quarter trim of both 51 and vin 2446 …. Polished up up few sets for future use. Vin 51 is in the same boat of unsatisfactory paint application….. soon to address that as well….. Cleaned up and flipped over the dash front cover trim, of 2446, I’m believing this is the true color “light greenish”… of both this part and possibly the correct hue of green for horns as well? Comments?

Those are some really nice upgrades to the base model examples. Were there "pre-package" Euro deliveries which did not have some of these package features, or were they pretty much all grey market from Australia & elsewhere? Also, which of the described features were on all of the Euro deliveries, or were things like spoilers an extra cost option?

Thanks guys. I really don't want to get rid of her but life is getting expensive. I have a kiddo who will be going to college in 3 years and I'm in a house with a very small garage. One day I'll have a big garage or shop again and I'm sure that's the point I'll regret letting her go.

Nice new ride!

My son has a 72 240Z that he was trying to restore. Last I talked with him, however, it sounded like he was giving up. It needs a number of areas adjacent to both rear wheels and there could be more patch work. With the wheel area he keeps saying that it is inclusive of the structural areas...and we may have the equipment, but nobody is a good welder/sheet metal worker. I was wondering if there are any recommended folks in Seattle that you all have used. Appreciate it Bob Weaver

Looking for a set of 15 x 6 American Vector wheels for 280 Z

Hey, I just wanted to follow up in case anyone was wondering—turns out it was the ECU/computer after all. Swapped it out all those years ago, and everything has been running perfectly. Appreciate your advice to test instead of just guessing. Helped me narrow it down and get it fixed a lot quicker. Thanks for the help!