zed2

Jim, When I click "Order Parts" the 403 error occurs. I may just have to reach out to David H. directly. Thanks, Keith

All, I am looking for a bump stop that matches the OEM as close to possible in size, rebound and appearance. (I have read that the aftermarket urethane is not as compliant as the original hard rubber.) Has anyone identified an alternative to the NLA original bump stop? Thanks, Keith

All, Does anyone have a link to the Courtesy Nissan Parts site that is working" Thanks, Keith

Does it appear shorter in length than the one usually seen on the 240Z? Keith

Recently, a pair of inspection lids from a Series 1 were offered on ebay. One of the photos accompanying the ad depicted the rubber cushion (63223-E4102) to be shorter and having a “L” profile dissimilar to the ones usually seen on early 240Zs. Has anyone previously seen a similar cushion? Thanks, Keith

I did extensive research on seat upholstery kits years ago. Naturally there could be changes in production in the marketplace since then. What I learned was that Seatz manufactures two different style 240Z seats based on production year. The primary difference is the length of the seatback material, since early years did not have recliner mechanism, and later years did. Distinctive industries only manufactured one length of seatback with the thought that the extra material could be tucked up into the seat back. Distinctive Industries manufactured the foam kit overseas to meet the specifications of their seat upholstery kits. Seatz does not manufacture foam kits and relies on dealers to offer foam kits to those customers who need them. Since each kit is hand produced (both Seatz and Distinctive Industries) there inherently will be variation in fitment to either original seat foam or aftermarket foam kits. To make matters more complicated, some cars have had their original seats replaced over the years, resulting in non-year specific seats installed in a dated car. With all these variables of mind, it is not unusual to have to shape the seat foam by either cutting the foam or adding additional foam. I personally went through three sets of seat upholstery kits, and ultimately had to return a set to MSA in order to have Seatz rework a seat back. Persistence is the key to getting the seats to original. This project can easily exceed 10 man-hours. Keith

As far as I know Distinctive Industries is the only one that has a mold for the foam. I will have to study your pictures to attempt to determine why you are getting a crease in the bottom outer bolsters. Keith

Garrett, I used zip ties to pull the flap (which contained the metal rod) to the metal rod across the seat bottom (below the Pirelli straps). This will compress the foam and allow you to install the hog rings. Remove the zip ties after closing the hog rings. (Zip ties are not original!😆) I had Sherwin Williams produce a quart of oil based color match. They used my seat rails as the basis for the match. (As long as your seat rails are not rusty and have the original finish, they are a great starting point... since they do not get direct sunlight, they should not be faded.) Keith

Perhaps photo at post 39 would help at Seat restoration Keith

Anyone have a resource for this decal: (From Post 1 at OK decals) Keith

Which "OK" decal is correct for a January 1970 production 240Z? A (Zeddsaver): B (ZZXDatsun): Thanks, Keith

This alternator (and engine bay wiring harness) has bullet connectors not the plastic spade connector. (Jan 1970 240Z production.) Keith

30 amp receptacle? (The seller is installing a roof mounted air conditioning unit on their Z.) Keith

Since the pandemic the resource I used in the US no longer carries the material. I found this source on eBay. https://www.ebay.com/itm/162029179414 There may be other retailers in the US who have the material in stock I recommend you search etsy and other upholstery supply houses for local availability. Keith

When using a Pirelli strap material: Each of the 8 straps are 18-1/2” overall. Each end of the strap is folded over the clip with an overlap of 2” Results in a 14-1/2” finished length strap. Other strapping material may have a different elasticity, requiring a different overall length. Keith

E85 compatible?

I recommend you use thick pieces of plastic rather than wood to increase the battery height. Plastic will not retain moisture the way wood would. Keith

The Kia rear door w/s is a bit longer than the front, and can be seamed below the threshold plate. The rear doors generally have experienced much less use than the fronts, therefore are usually in better condition. Keith

Thank you. Keith

Great offer, I may take you up on it. Thanks, Keith

Rich, Thank you so much! Keith

Rich, Is there an item/part number you can identify? https://woodlandscenics.woodlandscenics.com/show/category/DecalNumbers Keith

Rich, Were you able to locate the stencil? Keith

Once again...time to celebrate and recognize Father's Thanks Dad for your guidance! Keith

Rich, do you recall the manufacturer of the transfer stencil you used? Thanks, Keith