Terrapin Z

I checked the door I have from a 78 and there is no bracket in the door like the one's shown above. There is no glass in my door so I am uncertain if there is some bumper mounted to the glass frame / support. I would say the bumpers ZCD sells will not work in 77 - 78 doors.

1976 and 1971 respectively, I think I have a 77 - 78 door I'll look again. I know those doors were different in a lot of way from the earlier cars. It was noted in the other thread that it might be a typo in ZCD's description.

My mistake before. The pad sits in the rear portion of the door. Slightly forward of where the the lock cut out is. There is a raised bracket that has a rectangle hole in it for the spring clip. I hope these pic's help. Pardon the rust.

Without it I expect the metal frame on the lower part of the window would hit metal to metal. I'll see if I can get some better pictures after work today.

When the window is rolled down the bottom edge sits on the rubber bumper. there is one on each side towards the front. Often the metal clip rusts out and it falls away from the mount hole. I couldn't find a good pic online either.

I bought a case. Build date 03/23 😎

I used a long wide, padded ratchet strap though the hatch. Soapy water, patients, and a helper to pull it back and get some screws in. It worked well and no scratches. Still not a fun job. (I did clean off all the old glue and debris off the frame.)

If you are still having issues with the blinkers, The wiring goes through the hazard switch. You might want to clean that one too. Perhaps you already have 😁

I saw you posted on FB as well. Did you find a set?

I’ll be a definite maybe on this. I am on vacation and can’t check at the moment. I am home next week if you have not found a set by then.

Do you have the rear shoes adjusted to spec. If out, they will eat up all your pressure before the fronts engage fully. Just an issue I ran across in my brake system.

It is not the same picture as above but this one does give a measurement.

A pretty simple pattern. The radius corners at the middle fold is .375" Here are the measurements. Looks like Roo has you covered on a set.

I'll get them out this afternoon and post the measurements.

Someone is buying, there are 7 items in his sold listings. The padded inserts are just spray adhesive stuck in there. Kind of like the headliner. I have some out if you wanted measurements.

Thanks for the confidence vote, but it is not my sale. I was just sharing the pictures from the OfferUp site as Craigslist did not have any. The amusing comment was in both ad's though.

Here are some more pic's $60k for S83

This link might work. At least for one photographer. https://www.facebook.com/media/set?vanity=bczregistry&set=a.791015816358692

I know what I got....

OfferUp is not a bidding site, It is more like Craiglist. It is supposed to hook you up with more local buyers. The have a seller reputation thing as well. One of their contact options is to "make an offer" to the seller.

I to understand, apologies for the delay. I hope the one you have inbound works out for you. If not let me know. I should have something that might work.

It had been an odd weekend. One of those “if it can go wrong it will”. i have a bin of collars that all have bearings on them. did you figure an overall measurement needed?

I am headed to a Z car show tomorrow morning. I'll see what I have that might help you out when I get home. There is a different one for the 240mm I bought my transmission from a 2+2 with the 240mm clutch. I used the collar from that car but bought a new 240mm clutch and aluminum flywheel. It works fine using the stock 240 master/slave and fork.

There are two collars for the ZX one fits the 2+0 NA with the 225mm clutch like all the280Z and early 280ZX, The other fits the later 2+2 ZX NA, and the Turbo with the 240MM clutch.