Topics Last 30 Days

Yes, which strut is that? Front or rear? In the front is a bearing about 40mm OD in the rear is a hard rubber disc with the same dimensions

Yeah, I wondered if you had. I don't spend much time there

amazing cars. like this.

Definitely the JDM one. My 12/70 looks just like the Captains.

My 12/70 #17770 has the black unlit switch.

I havent seen this posted anywhere on here: Carl B, do you have in on your VIN records?

@Pat Horne Good luck.

I have one of each type, this one is from #6521, 7/70 And this one is on #957, 1/70. Hard to get a good pic when it's still installed. Both have the Hitachi logo.

Bump. I am still making the retainers and the magnets. Bearing retainer are for electronic pickup distributors from 1974 to 1978 and matchbox distributors from 1979 to 1983. They are slightly different. The matchbox distributor was used longer in Europe than in the USA so you may fid a matchbox distributor in a 1984, 85 86 vehicle overseas.

While at a car show this past weekend, had a very interesting conversation with a gentleman. His parents opened a Datsun dealership in Moose Jaw, Sask. The year was 1966, he said that the family home was on the same property and he grew up working in the shop. He remembers the day the Datsun Training trailers pulled into the yard and all of the mechanics spent a week going through the courses. He gave me three of these plastic bags, he says he has lots more Datsun stuff . I am working on getting a chance to go shopping through his collection.

I really know nothing about these folks but they're local in the Salt Lake City area. JDM Legends – JDM Legends Store Here's a video they did a while back on a 1972 240Z restoration. JDM Legends - Season 1 Episode 1 - We Are JDM Legends - video Dailymotion

Her name was Elizabeth.

Namerow, Were you successful with the braided hose? Keith

I have wheel and tires sets for 240z, 280z, 280zx, and 300zx cars. Some sets are OEM and a few aftermarket wheels. Most are in great condition. I set of early z cylone wheels not so hot Let me know what your looking for and I will let you know if I have it. Pick up only in Northeast NJ. Will be posting pics in the next few days. These have been in storage for 20+ years.

So you used the original ignition switch hardware and just replaced the electrical piece that attaches to the harness?

I didn't trust my ability to hermetically weld the tank. So I assisted a friend while he tacked it together. He then took it to a mutual friend with a TIG welder and finished it up. At this point, I poured more Red Kote into the tank and allowed it to flow over all of the seam. I let this sit for about a month to cure. Then, I sealed off all of the openings and blasted off the remainder of the external paint. Interestingly, there were dozens of small hidden rust spots beneath the paint. You couldn't see them through the paint. But when the media hit it, the paint would flake off, revealing a brown rusted spot. After blasting, ready for paint. I primed and painted it with Rust-oleum automotive paint in rattle cans. It turned out decent. No one will be looking at it. Note I didn't remove the original rubber blocks. They were stuck on really well, and not damaged. I did remove the original foam rubber piece near the sender hole because it was falling apart. I replaced it with a similarly-sized piece of 1/8" (3mm) thick EPDM rubber, just to make sure nothing would rattle. You can also see where I masked off the factory marking, just in case anyone might ever care if the tank was original. Lastly, I leak tested it by putting a few gallons of gasoline in it and allowing it to sit on each edge for 30 minutes. The sun was out, so the tank heated up and pressurized, which was a good sign. I'm happy to report that I've reinstalled the tank in the car, and it works fine. No leaks. And no more plastic gas can bugeed to the rear shelf.

I'm all LED except for the dash. I used a couple of these from Amazon for blinkers and emergency flashers and they've worked just fine since I installed them back in 2017. Amazon.com: VOFONO 2-Pin Electric Flasher Relay, 12V Heavy Duty 2 Pin Compatible Automobile Motorcycle Bike Scooter Fix Turn Signal Bulbs Fast Hyper Flash，Two Prong Round : Automotive

Haven’t solved it yet. Having work done on the house and can’t get my car out of the garage. Hoping in a few weeks I can look at it again

YES!! Glad to have you back :)

Wow! 😝

April 1970

Got it, I'll give it a look. Thanks!

Some options to investigate: https://upgarageusa.com/pages/nos-parts-we-have-instock-for-1969-1995-z-cars https://vintagerubber.com/datsun-240z-260z-front-bumper-guard-over-rider-strip-kit-69-72/ https://jdm-car-parts.com/products/front-bumper-over-rider-vertical-strip-set-for-datsun-240z I believe I have a spare set of aftermarket ones as well - I think of decent quality. Let me know if you would like to see some pics of them.

If someone is looking for an original Bosch version of the 280Z auxilary air valve here is one in NOS condition. Its for a 1976 Porsche 924, but it's a very similar system. Marktplaats≥ Lucht by-pass regelaar Porsche 924 ('76-'88) — Motor en...Lucht by-pass regelaar Porsche 924 ('76-'88)Lucht by-pass regelaar Porsche 924-Porsche 924, 2.0liter-Voor koude start regeling (lucht)-Bosch-Getest en

They definitely were. Did that cause the brakes pads to tighten on the rotors? There was some brake dust everywhere. I ended up doing 3 things at once, flushing the brake fluid. Disassembled the calipers, and repack and set the wheel bearings correctly. The wheel bearings heating up may have caused air in the brake fluid to expand and tighten the brakes, I don't know. I just finished it off by adjusting the pedal to the floorboard distance, it was 7", now it's 8". Same with the clutch pedal, it was an inch off. Then set the master-vac push rod length to 3.5mm below the flange surface. I had backed everything off while 15 miles away trying to get home, not knowing what was going on. Things are looking good now.