madkaw

It's a little unnerving to have the starter still engaged when the car is running. I have to force the switch back to the run position. I've been searching and coming up short. I found some posts refering to the back of the switch needing replaced and also lubrication thru the key hole. Anyone want to share their experience with this with their solution? links to other threads!! thanks

Are you sure that's not a black wire? Also, on a 71 I will guess that the wiring is NOT complete behind the radio. There are numerous threads about fuel pump wiring on these early Z's. I would have gone with the RX-7 pump, which is also highly recommended on this site-and very quiet compared to the Carter. I would strongly recommend running a relay kit that you can order from jegs or Summitt. I believe I touched on this wiring in my Triple Mikuni Thread

Carl, that's exactly what my feeling are about the Wildwood upgrade. It's the linear control at any speed and the confidence I feel when braking that sets this system apart from maybe others. I have driven stock Z's, but not with minor brake upgrades, so I can't judge one against the other. In a lot of hard driving-not track days- I have never locked up, only once in a panic stock to avoid being crashed by someone else. I would bet the stopping distance would NOT be the same.

From someone who is running a complete Wildwood kit from AZ Z car, this is a very nice upgrade. Yes, very spendy, but an upgrade that will never need to be upgraded. It's done concerning brakes. I considered many options and in my opinion the extra money was worth the ease of installment and not looking back again. More than enough for my HP rating and my driving habits, but has never felt overpowering and actually the brake feel is as good as any modern sports car I have driven. Yes the rears are way overkill, but my logic was that I will never visit any kind of rear brake work in this car's life time.(kind of miss the parking brake though:)) Yes it was also about the bling of having 4 wheel discs, but these work very well and Dave sells a well thought out kit.

Thanks for all the input guys. Glad to hear this isn't the only A trans that makes this noise. The problem is that the car is going to be going on the market soon and I am just trying to make sure it's mechanically sound. The noise is really prevelant at high idle-like when I first start the car and the choke has raised the idle. When idling at 700rpm, it is tough to hear. I don't have a lot of miles on this car since it has just now getting road worthy. I will see if i notice any change in fourth gear. The other problem is that I believe the diff is noisy too-which is making it hard to differentiate between the two noises. Again, I need to get more miles on this car. I imagine a lot of these issues are from the car not being driven enough. This 71 has 85k original. It probably sat close to 20 years wihout rolling anywhwere, which i would think caused dry spots on the bearing that led to rust. Not sure if some driving will help wear anything in or not. I have a spare r180 coming for the diff incase that is part of my issue. I think I better find a spare A trans.

Yes all parts are new and yes the noise was there before. Need to drive it some more- just got it back on the road - let you know about fourth gear

http://s2.beta.photobucket.com/user/_mad_kaw_/media/jimderk002.mp4.html Might need decent speakers to hear this, but I'm just idling in the garage and depressing the clutch when you hear the noise change.Basically- depressing the clutch makes the noise go away. New clutch, PP, bearing, pilot bearing, tried adjusting slave unit and doesn't make a difference. So maybe trans input bearing? Car also makes a whine noise going down the road that only changes with speed-not gearing. I thought it might be the diff since they do have a reputation, but maybe this is all trans related.

An NA cam would be fine, but aren't the p90 valves shorter length- not sure what that would effect . Hell - you could just throw on the NA head complete and b done with it!!'

Love to see this car in person if you ever travel south. Please try and make to the next Midwest Z fest in Nashville Indiana. You have about sold me on the fender mirrors-looking good. Brave to do black, but the rewards are nice.

Is it me or is this section hard to read and use? There is no breaks between ads, or at least the breaks are not obvious. I don't know what to click on to see the ad, but sometimes I just get lucky. The OP is not easily defined because of the non-sectioned pages.

Wasn't one of the bigger issues with the dealer installed early units was the weak fan ? The fan was to weak to draw and circulate the cold air.

You guys are awesome! What the problem wind up being is that my antenna is a reproduction or a later year and the original bracket does not mount up with this antenna-(sorry Dave, but if I use the original broke one I will have the bracket thanks to you!) I managed to make a bracket to mount the antenna I have and got installed . Problem is the antenna worked twice and quit Also the replacement antenna I have seems to missing some kind of grommet. With the antenna installed i could see day light around the mast-water would pour in there. The OEM antenna is definetly built better. The pain with all this is that it is keeping me from finishing the interior install in the hatch area. I'm about ready to order a plain old antenna-non-retracting- and be done with it. Any suggestions??

Dave, thankyou for sending that bracket-but I still don't see how this antenna attaches. I can tune some triple Mikuni's , but this antenna is killing me! The thing that throws me off is the angle the antenna must have to sit at to utilize the stud. Also the offset that is needed to clear the interior plastic panel. Someone want to make it even more simple for me. I did google the pics on the antenna. The bracket for the 280z as shown above seems a better choose. The antenna that I have to put in the car looks identical to the original as far as mounting points, so I think I have the right antenna.

Guys, still following this thread-even if I'm a Mikuni guy- I have contacted mr. Franck and he responded. I have never been able to get into Sidedraft Central Yahoo group-which was mandatory if I was going to be part of this experiment. I have resorted to getting a Yahoo e-mail account to see if that helps. keith wrote me saying that I might benefit from the tubes if my car did not pass the F.I. test-you guys might have touched on this in this thread. I'd say I am border line in that aspect. I have been reading the last few posts and it sounds like I am where you are as far as a slight hesistation during hard tip-in at lower rpms. No coughing, sputtering, spitting-just a millisecond of hesistaion, so maybe i'm at a pretty good point. At higher RPMS, above 3500, there is no hesitation. I have tried quite a few things, but don't know if I have ever completely gotten rid of that slight studder. Other than that, these carbs have really been wonderful. I am going to put some fresh needle&seats in the floats so I know everything is good, and i am going to take to the dyno! This weekend I even played with valve timing to see if that would change anything concerning hard tip-in at lower rpms-it didn't. I did quite a swing on the cam timing and basically put it back where it was-slightly advanced. I have noticed watching my AFR's that WOT AFR is dictated by when hard tip-in occurs. If I stomp it at 2500rpm the AFR's look super rich for a while thru the rpms before getting to the 13 range. If I start out at a higher rpm the AFR's look much more optimum thru the remaing rpm range.

I see a ZX parked at the Napa truck repair place under the bridge-looks like someone is working towards a brake job.

I'd like to offer up help with providing hardware. I have parted out several Z's and have drawers of hardware. I have kept all the unique stuff and a lot I might never use. So drop me a line - I might have that specific bolt for your car.

Thanks guys-i just went out and found that stud. No wonder I didn't see it earlier, it is way foward of the antenna. I wll google to find the bracket.

I'm trying to install a power antenna on a 71. I can't figure out how the bottom of the antenna attaches to the car. I am missing the bracket, but I would make one if I had a clue how the antenna is positioned in the quarter panel. I have searched and found some pics of power antennas with the brackets attached, but still having a problem picturing how it is installed.

So I understand that the tranny shifted fine before putting the correct shifter in? After installing the correct shifter the problems occurred? I guess maybe I'm not understanding what was wrong with the original shifter that worked fine in reverse.

What kind of issues are you having with the drivetrain?

More stuff to look at when I get over there - besides the bumper!

Yep, I just posted this the other day. It only takes just less than a 1/2 turn on the diff mounting bolts to create a clunk. The ONLY way to tell is get a wrench out. I think folks like me that have had the diffs out on several occasions find that the STUDS are actually loosening causing the nut to be loose. Time to get the loctite red out and squirt those studs in place.

Okay, am I stupid or what, I can't figure out Sidedraft Central. I have tried creating an account and I keep getting caught up in a loop of trying to change or create my profile. I have never seen a forum like this and I feel a bit lost. It seems the page recognizes me on Sidedraft because I see the "hi Stephen", but I have no access. I don't have a Yahoo account per say, I registered with Google. What am I not seeing here?

I do have a wideband guage(innovate) installed already. Great investment for any carb guy. I find myself watching that guage more than any other in the car, so much that my oil pressure would drop to 0 and I wouldn't notice I have not attempted datalogging yet, so I need to get into the software aspect of this. I believe I already have logworks downloaded, I just never have used it. I will join sidedraft central and be glad to post my findings. I appreciate the oppurtunity to do this. I haven't had much time for tuning on my car lately since I have been trying to finish out a 71 for someone else. I was hoping in the near future to take my car to the dyno with the Mikuni's and compare to my SU's. It sounds like I need to do this before the get the hypojets installed for a direct comparison. My plate just got really full!!

I'll be a guinea pig!