conedodger

Oh, by the way. does anyone know of a manufactured block off for the cold start injector holes? God help me, if I have to manufacture one, I'll end up making it into a nitrous port! OH NO!!!

Started dressing up the intake. The Protunerz fuel rail is a beautiful piece but as you can see, the mounting bracket comes up well short of the stud coming out of the head. No problem. I'll remove and replace the stud with a longer one.

Picked one up for $30 plus shipping...

Sorry I wasn't clear @Captain Obvious. What I meant was here, in the classifieds. Because then, I could ask for a measurement. On ebay, no such service available. I will check ebay though...

Before this is over, all of us will know someone. I’m sorry for your loss...

I’m surprised they aren’t commonly available used. I guess a popular mod is to replace the stock one with a 75mm aftermarket one.

Ok, I have a suspect. Turns out, the 350Z DBW throttle body is 70mm with the same bolt pattern as the L6. I have to figure out if the pedal will mount but we have a suspect. Naturally, the pick and pull closest to me doesn't have a 350Z...

Thanks, I hadn't put numbers to it. If I can't find a DBW Throttle body gas pedal combination that will fit, one of my alternative solutions it to put a spacer on the manifold that I can mount to. For some reason, I can't find the online calculator I used to come up with the size TB I need but somewhere between 65 and 75 should feed a 3.0 stroker don't you think?

It shouldn't be a problem Captain. I made a foam core template of the gasket so I can go into the Pick and Pull with proof before I buy!

Captain, Modern TPS uses really two TP sensors to determine throttle position. It has one that measures the position from one direction, and a second that measures it from the other. That actually does look meaty enough to bore it and put a new butterfly in it. Thanks!

I may source one to see if I can adapt the DBW and TPS to my Big Throat TB. Thx...

I'm hoping to go Drive by wire (DBW) with this engine. If you've been following along, you know that I am using an N42 intake so I need to find a throttle body that bolts up and has the throttle actuator and throttle position sensor installed. It should be in the 70mm - 75mm range. Anyone know of such a beast? I know that HybridZ is probably the place to go for this, but I can't seem to log in and the email that I originally signed up with is long dead.

Well, I have mine as a core and I would think a 73 240 would be less common than the later ZX's. Which size did you go with? I tore all of this out so I could refinish the engine compartment. I've owned the care for 40 years and I have painted the exterior 3 times. Once red, once yellow, then back to the original white but I've never painted the engine compartment and it looked so dirty after I did the last repaint.

Good to know. I was going to have the booster rebuilt but I could go larger. I have plenty of room. I will no longer have any throttle linkage so...

@Yarb, indeed, that is what I just pulled off. I still think I will go with a 1" Wilwood. I'm going with bigger brakes too as I'm doubling my previous HP...

I wish there were old timey paper pics. I was discussing Brainerd International Raceway in the Boobs thread this morning. On another occasion, I was out in the middle of the track with my BF Mick. He was driving his 4WD truck and I was the front seat passenger. I had my Canon AE1 and a 100-300 telephoto zoom lens. I was looking at the girls sitting in the back section of the jeep in front of us when one of them started flashing me. I stared and Mick yelled "shoot pictures!" I said, I'm out of film... He said "They don't know that!" She jumped out of the back of the jeep and ran back and handed me a piece of paper with her name and number on it. We didn't spend much time together. She was crazy and I was a med student needing less crazy at the time.

I realized that after I looked up the M3... YIKES!

@grannyknot, my proximal problem is finding a DBW throttle body that has the proper bolt spacing to be bolted up to the L28 intake manifold. Mind measuring your bolt spacing? 😎

So Yarb, I looked in to it. Turns out I didn’t have to look far. That’s what is on the car now!

I’ll look in to it, thanks!

So a little more stuff came today. The fuel rail from ProTunerz in Canada. Nicely finished piece.

Thanks Yarb! I think it's a family operation. The kid spoke up on Facebook and said he was in SoCal...

Ok, I sorted out the Wilwood MC situation by checking Silvermine Motors site. Next question. Who rebuilds/restores brake boosters?

Anybody know which Willwood master cylinder replaces the factory one? I am fairly sure it's a 1" MC but I'm looking for a part number so I can go shopping...

Pictures would be killer. I'm trying to imagine your problem. My Datsun Competition headers, which are more than 4 decades old, can't be installed with the steering shaft in place. I have no other fitment issues and have actually fabricated heat shield for the brake plumbing as boiling brake fluid is no bueno. Show us the problem.