Jump to content

HusseinHolland

Free Member
  • Joined

  • Last visited

Everything posted by HusseinHolland

  1. STB 3B-250273 Comes with all these bits... It's raining, so I can't look at installing mine until tomorrow
  2. So it's pretty much self evident when you look at the accessory bits that come with the strut? I didn't know they came with any adaptors
  3. Thank you - I'll check it out. EDIT - I saw a recent one with the control head, is that what you meant? I didn't see a more detailed one scrolling through your video library I'll do that. I tried to take a pic yesterday, but I didn't have sufficient lighting.
  4. Is this new valve in your post the 4 seasons part, or an OEM valve? I'm assuming OEM, since it has the I/O tubes? My 75 280Z has AC, but looking up under the dash, I don't see the bulkhead valve, only a heater valve. All the lAC lines look 'universal" with the hose clamp fittings, not crimped lines, so mine is perhaps a dealer installed version? Maybe that's why he said the AC never really worked, because there is no positive heat shut off? This leads to another question - if the dealer kit differs from factory, would that mean the control head also has no vacuum switching? If I add the positive shut off valve, I will need a switched vacuum source to activate it...
  5. The caster rods? They are buggered along with every bushing. I can take the right front wheel & move it fore/aft about 6 inches(!) The control arm bushing is GONE. The left wheel bearing is toast... I bought a full poly bushing kit for the car, along with the OEM diff mount. Also new Eibach springs, KYB struts & balljoints. I didn't buy any rack related parts yet, besides the mounts. I found both boots are gone. The rack itself seems to be OK, I do need to recheck the tie rods.
  6. Finished the install after work - did the motor mounts first, since I had the car jacked up anyway. The car has 250K miles, I don't think he did any suspension bushings or any mounts in all that time. I'm happy with the fit & look. Not sure I needed to splurge for the Skillard grille, but I didn't want any of the gap I've seen without a full grille The bumper fit is very good
  7. I will figure it out when mine strut arrive, it's odd that no one who's used them has responded....
  8. I bought a used steering wheel off eBay, listed as applicable to 240/260/280Z, as mine is 'squishy". The listing implied it was a factory wheel, and it appears to be. The problem is it has no hub, and since I'm new to Datsun, I didn't realize that the stock wheel in my 75 is not detachable from it's hub. So, Can anyone advise me on what hub I need to look for to make this wheel work? Thanks in advance image from listing, it specified without hub or horn button shown
  9. Had a few hours after work, so I focused on fitting the Skillet grille & the front bumper & brackets, after I replaced the 3 pedal pads Brackets in first, then test fit bumper With the bracket alignment figured out, I worked on the Skillet grille. 4 brackets are loosely fitted to the grille prior to mounting. I bought the full grille, not the bumper version, as that version has large cutouts on either side. I cut narrow slots to allow the bumper brackets to pass through Then I put the bumper on before I ran out of light. The fit is really nice. 4 M10 studs secured through the brackets with 17mm head stainless nuts. I'll put the spoiler back on tomorrow. The only catch with doing it this way, is that the valance has to go in after the grille, so the 3 mount screws , and then the horns have to be fitted from above. There are small bumper blocks that I also bought from ZcarDepot (800-924). A M6 bolt passes through the fender & into a captive nut in the bumper
  10. Yeah, the motor has 250K miles on it. I'm surprised the compression is as good as it is, really. I'll recheck it after loosening all the valves back into spec range. Thanks - So the large base nut (17mm) is the lock, then there is a 14mm? nut built into the shaft, I'm assuming, since it's tucked up against or under the rocker? I couldn't see it last evening. I'll look closer in better light. I'm used to MG/Volvo/Fiat/Honda layouts, which all had an obvious adjuster. I appreciate that tightening the lock typically reduces clearance, I usually shoot for the looser end of the clearance range when adjusting.
  11. Any pics of the adjustment operation? The above tool set is helpful - The Nissan 75 manual has no detail on the process, that I can find beside this pic in the Engine Mechanical section I tried to figure it out from the pic of the valve layout. Not clear to me, besides that the 4 elements on the left are the adjuster Mine are all way too tight - can barely get a .010" feeler in there (checking #5 exhaust here, as that cylinder only had 145psi vs 168psi on the other 5)
  12. In all the video installs I looked at, they seem to have issues with the spoiler dropping/warping - the 280Z has a valance that the spoiler sits against, if you don't remove it.. Clamped the middle to secure it, marked & drilled the 4 outer end attachments. Instead of futzing with nuts & bolts, I just used M6 stainless rivnuts & M6 sems screws For the leading edges, I used plastic body clips instead of bolts Added two rivnuts to the center section to anchor it All together (for now). I have a tall Skillard grille coming, and chrome skinny bumpers to complete the look. Ultimately, the spoiler will be body color. Added tape to where the bumper trim bolts went, covers up the extra unneeded holes. I'll make some brake ducts, so those cutouts don't look out of place
  13. I saw this thread last week, and ordered a pair off Rock Auto for mine. Not here yet.
  14. I'm going to have to work on the HVAC in my newly acquired 75 280Z - the PO said the core leaks. I'm reviewing your Escort core mod for that (so far the pics are all dead, but only on page 2). As far as this mod goes, you don't mention the heater control cable, does that mean you used the stock cable & re-routed it out the firewall? I do like the idea of the valve being out of the dash area.
  15. This one looks closer to what I have (looking on Amazon), with more posts, however the circuit rating is fixed
  16. Its an MTA 0300839. Connector ID is a US distributor. The cable terminals & fuses are sold separately, but listed with the main component so it's easy to figure out what you need based on the gauge wiring you are using. EDIT - uses Midi & Mega fuses
  17. As an aside - I'm actually English - moved to the US when I was 19 - I used to own & work on British cars after I moved here. I was quite insulted by the joke at the time. It did seem to be true unfortunately.
  18. There is a saying in the US - "why do the British drink warm beer? - Because they have Lucas refrigerators" 🤪
  19. This is what someone did to 'repair' the fusible link for the EFI. The ground side pulled right out of the butt splice seen below. I'm adding the fuse block New cable ends crimped for EFI feed and starter cable Clears hood inner frame
  20. Any double function (assuming you can find one) relay is going to take up as much physical space as two standard relays. At that point it makes more sense to stick with the factory setup. You can buy 'gangable" relay sockets for Bosch style Micro and Mini relays, so you can keep it pretty compact space wise.
  21. Indeed. Since the Nissan EFI has the ignition pulse to the ECU, there is no reason to use anything complex here, just a question of single or double throw.
  22. The only question I'd have is whether the standard micro relay rating (25a) is sufficient for an external fuel pump. It may be safer to use the standard cube/mini relay for that?
  23. Nice! Although no Volvo ever used that relay - looks much the same as the one Fiat used for it's L-Jet in the 80's though. Personally, I'd look to update to a less expensive controller, if mine were bad. I'm of the mind that if it ain't broke don't fix it for most things, however if I need to do any rewiring on mine, I'll probably go with a less costly 2 relay setup
  24. I haven't reviewed the Z EFI wiring diagrams yet - however, if the system relay requires an ignition pulse to trigger the injector ground circuit like most Bosch EFI, then there are various relays that can do that. This Volvo-based page (about half way down) has details on using a VW relay - 321906059C, 321906069D, 321906069G or 321906069H. There is discussion of timed pulse for the pump(s), since that is a feature of the LH systems Volvo uses. Perhaps that will serve your needs?
  25. Yes, the function of the fusible link has been wrung out over the whole thread. It is also known that the heavier rated fuse types were not in production in the early 70s. The PO of my car (owned it from new) told me he had issues with the links. Who knows what rating he was actually given, and whether it was appropriate for the '75 spec. I'm just going to go with the equivalent ratings (40a = green, 80a = black) based on the chart I linked. I see no reason for concern. If I were interested in keeping the car completely original, I would source the appropriate wiring. I can appreciate that there are people to whom that matters.
Remove Ads

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.