Zed Head

Do you have a plain old timing light? Just to get your initial timing right. You're spending a lot of time on a simple thing. Or just set it to zero, where it flashes intensely, and use the third mark on the pulley.

I have a 1995 Pathfinder with 248,000 miles on it. Just kidding.

This picture is from the 1973 FSM. Yours is close. Here's a good old thread with more numbers. But yours isn't there. Mike, Walter's thread would be a good one for the knowledge Base. @Mike

Here's an old picture I had of an R200. You can just see the rectangular piece of aluminum molded in to the bottom of the cover. And you can see the rounded corners.

Looks to me like your float hanging brackets are bent. Like somebody twisted the float. Pretty sure that they should be straight. As I understand dial-back timing lights, they always flash just like a regular light. The dial is turned until the flashes happen at the zero mark on your crank pulley. The number you read on the dial is the timing advance. But they always flash. Or you can set the dial to desired advance and move the distributor until the flash happens at zero. You can also set the dial to zero and just use the marks on the pulley if you want to. So it's not really clear what you're measuring. Could be a technique error.

Interesting thread and stories for sure. But you've told more about other cars and other engines than the one you asked about. You asked for an opinion on what the 1970 240Z is worth, I think, but it's still not clear what it is. Not trying to negatize your thread, just saying there's not much about the actual car you asked about. I added a detail and removed one below. 1970 240Z Raced by friend of Bob Sharp. 41K miles newer model 5 speed flairs? real louvers and an old style bar come with it but need bolting down 2.4 BRE motor with BRE covers and comp cams. yellow paint

Is it a track car or a show car? Has it been on a track, in a race? Who built the car? Not clear what it is. Sounds like the picture you posted isn't of the car you're describing. I summarized your ad below - 1970 240Z 41K miles newer model 5 speed Huge TR8 Group 44 flairs real louvers and an old style bar come with it but need bolting down 2.4 BRE motor with BRE covers and comp cams. yellow paint

And no photos.

The vane scraping is bad and could cause fueling problems. Sticking open will make it run rich. There's a backfire relief valve in the vanes of later model AFM's so the vane doesn't get bent. It is a thing. The 228 and 128 aren't terrible. Not clear the the AFM is worthless although it does need attention. I'd tweak the vane until it moves freely. Check the counterweight on the other side also. The little bullet might be to the condenser/capacitor also shown in your picture. The 5-sided box is the junction box for the wires from the distributor to the ignition module in the cabin. If you don't have wires from the distributor there you might have an ignition module modification. The white doohickey is a test port, for the BCDD I think (Emissions chapter).

Did you?

Easier to just look at the rear cover, or the area around where the axles insert. The R200 has a rectangular chunk of aluminum, about 1/2" by 1", underneath the drain plug and the cover is almost round. The R180 is smaller and has a rectangular rear cover. It also has a ring of bolts around the axles holes, where the R200 does not. Look at some images on the internet and you should be able to tell with a glance. If your 75 is a manual transmission coupe it's almost certainly an R200. Or you could post a picture and we'll just tell you what it is.

Looks like it would clean up well. The bumper rubber looks in pretty good shape, probably protected from the sun by fir and pine needles. Looks like it's been painted, so could be hidden repairs. They say it needs a tuneup so they probably started it. After sitting twenty years who knows what got dragged through the engine when they did that. Still, not bad.

You don't have a timing light? Who rebuilt the engine? Are the fender wells cut under those flares or are the flares just attached on top of the stock body? Also, it says complete interior but there's no carpet. Do you have the bumpers? And what's going on with the key hole? Questions that come to mind...

The MSD and the ZX are probably about the same at higher RPM, like 3000 and above. The MSD's multiple sparks can help at idle and low RPM, especially with an engine designed for high RPM power.

Do the resistance and voltage testing at the ECU connector before you get too crazy with cleaning. After the cleaning, you'll get the satisfaction of knowing you made something better or the agony of knowing that you broke something that was fine. Both good reasons to have a beer.

I'm no web programming wiz but if I "inspect" the video it shows as an HTML thing, with lines of code that say "js context". Made an image of how the video just inserts itself in to the middle of a paragraph. If you're moving down the page the text will all shift downward as the video ad shoves its way in to your life. I might start sending nasty messages to the companies that use the ads. One small blow to save the world. By "adware package" do you mean what's commonly called malware? Are you in advertising? Are you part of this!!! Anyway, I haven't found a plug-in or program that will stop just the ads but allow other desirable things to work.

I wouldn't worry too much about where the distributor adjustments are, if the timing light shows you're right. All you care about is when the spark happens, not where the nuts and bolts are. Each mark is 5 degrees so the third should be 10. 10 degrees of advance will give you a faster stronger idle than zero. Get that set and see if you can get it to idle on its own. Then you can tweak and tune to make it work better.

10 degrees is a good starting point. Zero is not the best. Sounds like you have the right idea though. Get the ignition timing right, then focus on the carbs. But even there, if once carb doesn't have fuel, that's kind of a "needs to be fixed" thing right off the bat. I'd focus on getting the carb to function properly (gas in the bowl), and setting the timing to 10 degrees. That's a "should idle" point, then build off of that. As far as setting timing, even if you have to squirt starting fluid and rev the engine up and down, you should be able to see where the low point is. Set it to 10 and assume that it's right. Sometimes you have to make an assumption and work with it for a while.

No timing light? I don't see any measurements. The engineers put those degree marks on for an important reason. It's important. If you've confirmed where zero is, with your screwdriver method, then you can set ignition timing to its correct spot. If you set and measure spark at the correct spot then you don't have a timing issue anymore. When you have that locked down then you'll know that your problems are somewhere else. Best not to solve two problems at the same time. You're lucky in that you have an engine that runs. From here it's a matter of confirming what's right, and making the stuff that isn't, is.

I couldn't even log in to my email account, Hotmail (aka Outlook) without javascript enabled. It's just email. I'm so tied to Hotmail/Outlook it's pitiful. Outlook sucks and Microsoft knows it and they don't care. 'cause they got you. Millions of people interact with Microsoft through email, and their email program is a giant steaming turd. Seems weird that they don't shine it up a little bit.

Well, the fact that it runs well with the pump off and bad with it on suggests a problem either way. Knowing fuel pressure is important. If fuel pressure measures correct check the vacuum hose to the FPR for fuel. IT should be dry. You can have good pressure but too much fuel supply due to a leak through the FPR diaphragm. Not uncommon to blow a diaphragm and fight a "running rich" problem for weeks or months. It's sneaky. Dielectric grease seems like a good idea and wouldn't hurt. But it makes everything greasy. If you drive it fairly regularly any corrosion you cleaned of should stay away. It's the sitting out in the moisture that causes the problem. There's a diagram at the beginning of the Engine Fuel chapter that is pretty good. Gets you close. Most of your measurements will be at the ECU connector though. Use the 1980 EFI Guide, it's very good. Covers all years up to 1980.

There's a technique involving a long screwdriver on the valve spring retainer with the camshaft as a fulcrum that you could have used. To remove the rocker arm, then set the pad in place. For future reference. They seem to pop out on older, probably gummed up, engines when people rev them up after getting the going again. Not uncommon. Hopefully you're good to go for a while.

Compression ratio is almost a useless number without knowing the cam specs. Cylinder pressure is what causes detonation, so higher pressures will lead to a higher likelihood of detonation. But, due to the variation in gauges out there, the range of the numbers measured is huge. In an ideal world, we'd all use calibrated identical pressure gauges and we'd talk about designing for a certain static cylinder pressure. From that starting pressure you can get in to taking about dynamic changes. CR alone doesn't tell you a whole lot though. It tells you which way you're going but not where you ended up.

All it really takes is one vacuum leak causing a low idle speed to allow the AFM vane to get too low and voila, a switch is installed. I would start by running the tests in the EFI Guide and/or the FSM. There's a test for the combined EFI/pump relay. It runs now, which is way ahead of many people's projects. If he removes stuff and it stops running then he's in a whole 'nother world.

Anybody out there noticed a new type of ad that pops up in the middle of a column of text while you're reading and plays a little video? Not on CZCC but other web sites, like the newspaper sites. Over the last few months I've spent more time clicking the little X in the upper right corner than actually reading. They seem to be everywhere. Can't think of a more annoying way to advertise a product. I blocked Flash in Chrome and they're gone. It even stopped autoplay videos on ESPN, a massive bonus. Edit - I knew this would happen. They came back. Never mind. It's probably javascript. The internet is messing with me. ESPN autoplay is still fixed. Edit 2 - Disabled javascript and the ads stopped but so did a bunch of other stuff. Some sites won't even load up. It's like they're all saying **** you, you'll watch our ads or you'll get nothing. I'm going to run lean, no ads, and some sites not accessible and see how internet life changes. I'm betting it will be better. Those video ads were killing me.