zKars

I'm actually quite impressed. All were identified more or less correctly, but no one got them all right. 1- Hatch luggage strap loose end keeper loop-thing. Zup 3- Spring clips that keep the under front fender seal in place. Very similar to choke cable clip, just bigger. Granny, Blue 4- Coat hook from early 240. Coat button really. . Blue 5- 2+2 door release handle, on rear upper portion of the door so rear seat passenger can open the door. . Blue, almost... 6- Throttle linkage spring, ZUP 7- Loch ness snowman caught making waves in Lake Ontario. Or door interior light push button switch, not sure which. Granny 8- Blower fan dropping resistor. 240z, 3 speed. Blue, Granny almost, 9- Turn signal bulb shroud in 280z Tach. 240 likely same. Blue Granny 10- E-brake cable adjusting nut. Granny 11- Un-snapped off ignition switch bracket mount security screw. Zup 12- Ash tray retainer clip. Granny And then there is the mysterious missing #2 that NOBODY mentioned. I was hoping someone would fill in their list and take a WAG at #2 anyway. Alas, it was not to be. Honorable mention goes to Zed Head for most inventive guesses. My job is done here. Next!

The one set I purchased was very impressive. And they stayed looking great on my very well used 73.

No judging, just a way to pass some time. After a few take their guesses and stew for a while, I’ll reveal the answers.

Making some progress. Lack of scale is hurting some perceptions... BTW, nothing is ZX or 510, just S30. I was VERY tempted to slip in a 510 thing but I resisted the urge.

Here. A mere smattering of what’s a bit “out of the ordinary” down in the dungeon. Have at it.

I’ll dig through my pile-o-stuff and see if I can find a few obscure parts and get you to guess what they are. Maybe some pictures taken super close up to distort the view.

Thank you. I can go back to washing my hands. We are of course expecting someone to do one of these quizzes every day now, right?

Somebody, anybody, tell me the answer! I need to get back to work and have that cigar.

Spring rate metric to SAE conversion units are inverted. Kg/mm to in/lb rather than lb/in. Numeric part is right, 1.48 kg/mm is 83 lb/in

“Without standard load” should be “with standard load”

You can also continue to use your speedo cable to drive your stock speedo and use a GPS based speed sensor to drive your ECU. I had an idea to build one of these last year, but I found out Haltech and ECU Master came out with one. As long as you don’t auto cross in a parkage or tunnel, this could work. https://www.haltech.com/product/ht-011310-gps-speed-input-module/

Given the tough position so many of us are probably in or going to be in soon, you can have 6 for $4k. Canadian. Good news is I’ll lots of time to make plenty. Got a big sheet of 18 gauge to gobble up.

See post # ... oh wait, no post numbers. Page one, 3/4 of the way down.

Final stage, a bit of dremel work to clean up any burrs and rough edges. Scratches on the back side need to smoothed from contact area on the mandrel. Quick abrasive rub, then sandblast for consistent finish. Off to plating with the next batch of hardware. Hopefully not too far in the future....

Part two. Use die to drill 21/64 hole Install on custom mandrel on the lathe and remove excess. Parted off to right length. Quick sand paper polish while it’s spinning. Flash clean up on the inner edge of the parted cut complete.

Had a chance last night to go through the process and take pictures for posterity. Won’t be taking them in for plating any time soon. Get ready Use a little bushing I made to center. Squish! Cup made Turn die over, put cup underneath and squish the wings flat. Makes the machining steps easier

I got in touch with Randalla. He has a big batch of new Float-Sync product coming.

@Randalla, please message me. Thanks

I was thinking of getting a Greenlee punch set to make easy round blanks. I noticed when I cut my square coupons into a hexagon, there was less distortion. I haven’t actually tried to start with a truly round blank to see what happens. I’m happy with what I’m making. And yes, I have seen the youtubes of people spinning HUGE aluminum disks in HUGE pots pans and other receptacles. Very long lever arms and very large lathes spinning them. Very impressive. I will not be trying that, even on a small scale on my lathe. I see another 3 week boondoggle coming up....

Quick update. Lot going on at home right now. I have a good solution going. Made the first group of 20-ish. Size is great, appearance comparison to original is pretty good. Drilling the hole after the initial forming is the only option. Any hole in the piece to start with is a) too hard to center, and tears out immediately, pretty much like the fender washers. Using a center hole in the FM part of the die makes drilling the hole in the middle very simple. Once I got the dies centered to each other consistently, I can make millions of identical little wrinkled creatures that only take about 175 finalization steps each. Easy peasy. I’ll have pictures to post of the whole process stages later in the week.

Nice and simple. As long as the oil streams all aim at the right place, it’s all good. If “I” were advertising such a thing, I would be posting video’s of the spray patterns at 10 psi (Idle) and 60 psi (operating) to give such a critical piece some semblance of trustworthiness.

I initially tried using a fender washer that had a 5/16 hole, and die parts that pass through the hole. Seemed like the right thing to do. This didn’t pan out very well, as the distortion that happens caused the material to rip around the hole. I now have a 5/16” hole in the female side of the die, so I’ll use that as a drill guide to put a hole in the part after it’s formed. I measured the original washer base thickness. It is as suspected a bit thicker than the walls, at 0.050. 18 gauge sheet metal is 0.048, guess that will do.

Three guesses what I did today. Dang process is very sensitive to several parameters. Centering of the dies turned out to be the biggest challenge. Lubrication was also a real helper. Corners are radiused. Once I got it right, I can duplicate . Twice anyway. I’d like to get the depth of the female die just right, so it stops and makes a nice flat bottom. It’s a bit deep at the moment Notice the pile of test pieces in the background. Next tricks are drilling the 5/16 hole (starting with 5/16 fender washers did NOT work) and cleaning up the excess. I plan on drilling the hole first, then using a 5/16 bolt and nut to make an arbor to mount it in the lathe, the clean up the flash there. No doubt there will learning moments along the way with that too. I currently only have 0.035 thick tin, the original washers have a .045 thickness at the turned up lip. Will have to go shopping Monday. I will have to reduce the diameter of male part of the die, to make room for the thicker material. I have .035 gap in the dies at the moment to match the material. They feel like they would be too thin and cheap feeling with 0.035 material. So making is possible it seems. More news on Monday.

Well that was too easy. A lesson on hardening, a lesson on materials, a lesson on drawing, what more can a guy ask? Thanks! Now I have to go try. I got the project car in the garage easy, parts gathered, getting all gung ho. Gotta slow down and turn a little stuff on the lathe first and take my time. Think I’ll use 5/16 fender washers as the raw materia (assuming they are 1” or more in diameter)l and put a 5/16 nose on the male side of the press and a matching 5/16 hole in the FM side of the pocket to guide the process. Need to make a nice flat bottom 7/8 hole for the FM side to get started. Hope the radius of the corner is nice and tight like the originals. Should be able to press hard enough with my 15 ton press. Fun! Looking for hardware, I even found some nice metric wing nuts with the right kind of “mickey mouse” ears that look like the originals. Apparently they are “German” style... Maybe I can work toward making replacement for the whole bolt assembly.

I've contacted Randalla and asked if I can help with supplying my version while his is un-available. I'm awaiting his reply.