laffeaux's Content - Page 2 - Classic Z Car Club Skip to content

laffeaux

Community Member
  • Joined

  • Last visited

Everything posted by laffeaux

  1. Once the retaining nut is off the sensor shoud just pull out. If it's not it's most likely oxidized enough to attach itself to the housing. Try to get it out, or if you need to MSA sells new housings.
  2. In the US the stock size for '71 is "175 H R-14." I'm not sure if the UK used the same size, or if you guys ever had the crazy system for giving tire size. I have my original spare and it's this size - an "H" is about a 70 or 75 in modern aspect ratio.
  3. A man goes to see a doctor and says, "It hurts when I raise my arm like this." The doctor says, "stop raising your arm." My advice is don't slide through turns with a full tank of gas. I've had many cars spill gas when I overfilled them at the pump.
  4. I want high quality rubber floor mats that say 240-Z on them. No one seems to make them. If you come up with those, I'm in!
  5. A Nissan dealer near me has one in their showrrom. I was picking up a part for my car and took a look (no test drive). I like the looks of the car, but it's not a 240. The 240 is based on the Britsh car designs, while the new 350 scream Germany. The new car reminds me of teh Audi TT, and definitely is aimed at the German competition. Maybe that does make it like the 240 - the British cars were the sports car leaders in 1970, and the German cars are today. Hmmm... Anyway, it's a great looking car, but to me it's like the last 300Z's - let someone else own it and I'll admire it. To me the 240 is where it's at.
  6. If you have a newer radio with a blue wire coming out, all you need to do is connect the blue wire from the new anntena (not the original style) to the blue wire from teh radio, and run power to the antenna. The anntena needs to be connected into a circuit that receives power when the ignition is off, and also needs to be grounded. There will be two wires running the length of the car - the blue wire, as well as the input power (red). The black wire goes to ground (anywhere in the rear of the car will do). I bought the MSA non-factory anntena and have had good luck with it. It works great with my radio. The installation instructions were a bit difficult however (i.e. there are about 20 adapters and you're not sure which ones to use with the car. I made it work in the end without the aid of the instructions.
  7. I noticed on eBay that there are two of bars listed for sale. Both bars are different and neither matches yours or mine. So I'd guess that there were a lot of different bars all of which were on Z's at some point (all were dealer installed, or aftermarket). http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=1856227246 and http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=1855529410
  8. The average person does not spend time everyday on a Z specific web site, and probably has no idea that people know (or care) what was stock. Like XYZ says, the person was probably parrotting what they were told when they bought the car. I see Z's and '60's Mustang's listed as having V-6 engines in the local newspapers all the time. The sellers generally have no idea that there is a difference between a straight and V 6. Most people hear "V-6" and know that they own a 6 cyclinder and think that the terms are interchangable. Remember if you come to a car site, you're probably among the upper percentage of people (in the general population) who know about cars - even if you know next to nothing.
  9. I'm sure that the mounting varried by year, as the bumbers changed over the years too. Also, there could easily havbe been several manufacturers. If it gits your car, and you like it, then use it. It's probably from a Z.
  10. The points are fine, they are two months old, and although I did not check the gap last night, there was one (the voltage checks I did were with the points open). Allso, I didn't touch them since it was running last. What's the "good" ground that you're refering too? The only thing I can figure is that when I was flushing the block that the exist tube from the manifold shoots water right at the distributor. I had the cap on the entire time that water was near the engine. Afterwards I pulled the cap for over 24 hours to ensure any water that did get inside dried. Maybe something didn't like the water that much? Possibly the condenser? I have no idea.
  11. I meant 4 speed. (oops)
  12. If it were a 5 speed there would be more interested people. It's hard to imagine a 240 auto.
  13. Here's what it looks like. As far as I know it came on the car in '71.
  14. I can't figure this one out. I just finished installing a new radiator, hoses, thermostat, etc. I flushed the whole system, and just replaced the coolant. All this took a few days. Today I tried starting it and it will not fire. I'm not getting any spark coming out of the coil. I've checked everything. I've gone through the Haynes Manual diagnostics and the coil, condensor, and coil wire all check out fine. But I'm still not getting spark. The only thing that I did to anything electrical system was to remove the heater blower in order to replace the heater hoses. I've not replaced it yet, and wasn't planning on doing so until I was sure there were no coolant leaks. There's no way that the heater is required to get spark is there? No way. Any ideas? With the points apart I get: I get 12V from the coil (+) lead to ground. I get 12V from the coil (-) lead to ground. I get 0V from the points to ground with the condensor wire removed. I get .005 OHMS from the coil to distributer wire. According to Haynes this means that I have no problems. Yet there is no spark leaving the coil. Any ideas????
  15. My override bar for my '71 mounts differently. I have two bolts per side, but one is above the bar and one is below. Not sure what you were asking.
  16. How much are you asking? What's the frame like? Where is the car located? (Not that I'm looking, but I'm curious.)
  17. My opinion on the triple carbs is as follows: A 2.4 litre engine is cable of processing 296.6 CFM of air at 7,000 RPM. A stock Hitachi SU will flow at 150 CFM, and since there are 2 of them, that's 300 CFM. For a motor that can not turn more than 7K RPM. what good will the 3rd carb do? (Unless you have a more direct air path to the cylinder, maybe.) If the engine turned 8,000 RPM, the engine can process 339 CFM of air - in that case more carburation is needed, and Triple SUs would be a cool set up. So my opinion is that unless you're making major engine changes, a triple carb set up is overkill.
  18. If you;ve not seen the ZTherapy "Just S.U." video, it's well worth seeing. See if you can borrow a copy somewhere, or spend the money on it. After seeing the video, the SU carbs seem so simple. It's hard to imagine not being about to set them up properly.
  19. laffeaux replied to laffeaux's topic in Interior
    The lights definitely dim when the knob is turned - they go from off, to barely on (and anywhere in between). I'll try to short it out and see if they are brighter.
  20. laffeaux replied to mmagnus's topic in Electrical
    My smog pump is still in place, and to me not polluting the environment makes it worth it. The reduction and weight and power loss due to pulley drag is negligable. The pump does not "fool" the testing equipment into thinking that there are fewer pollutants, it actually reduces emmisions. If you're using the car as a daily driver, why not do what you can to help reduce smog? From what I've heard on another form, removing the smog pump does not really increase power, as the end of the lines still stick through into the exaust system and block exaust flow. If you want extra power the fittings on the engine need to be removed. Otherwise all you're doing is increasing pollutants.
  21. laffeaux posted a topic in Interior
    The dash lights on my car ('71) are really dim. The bulbs are new. The brightness adjuster goes from "off" to "barely on." Could this be the fault of a bad adjustment switch? Are they hard to replace?
  22. My late '71 (5/71 production) came with 4 screw carbs. I'm not sure when the switch to 3 screws occured, but I thought it was on '72 cars. The fun thing about the late '71s is when you order a part you never know if you need a 70-71 part or a 72 part until it shows up.
  23. Seeing triple SUs on a Z would be kind of cool. However, I'm not sure you'd ever get a 2.4L motor to need so much air that the extra carb would help much - I guess when you were turning 8000 RPMs you could have all three carbs half open?
  24. Compared to $71,500 for the "last" Camaro, $95,000 for the first Z sounds like a great deal. http://story.news.yahoo.com/news?tmpl=story&u=/ap/20020903/ap_on_bi_ge/last_camaro_sold_3
  25. My first foray into Z cars was an early '71 that I bought in 1990 for $1400. The car ran great, and althought I thought I new how to look for rust, I did not. The car ended up with huge rust problems, and after a year I gave up on the car. A year later I jumped back in with an early '74 260. I spent $2000 and the car was much more dependable than the previous 240 - sure, it was less fun to drive, but rarely left me stranded (whereas the 240 left me on the side of road many times). Unfortunately, someone decided that they wanted my car and stole it one night in NYC. I never saw it again. I got away rom the Z's after that and bought and partially restored a '67 Firebird. I sold it after 5 years for about 1/3 of what I'd spent on it. Drawing from my past experiences this past summer I bought another Z. This time it's a late '71. I was looking for a car with good body and engine for about $6000. I figured I'd buy a car that someone else had already spent the money on. Well, as it turns out you can;t always get what you want. I found a car with a good body, but it needed mechanical work. In the end I'll have spent about $7000, but I'm getting a car in hte condition I wanted. What's most important? (1) a solid rust free body, (2) a complete car, so that you don't have to guess what it is you're looking for, (3) a good interior, and (4) an engine that does not blow blue smoke or leak oil.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.