All Activity

BOT.... btw.. Matt have you finished your car?

Thanks for information!

Haha!! Not sure. Who would I ask for confirmation? ☺️

Odd story. Purchased and restored to street form by a dentist. " : in the garage of a dentist who had purchased it in ’73 and returned it to its somewhat original street-legal state. " The show is next Sunday in Florida. Ponte Vedra Auto ShowPonte Vedra Auto ShowThe Ponte Vedra Auto Show | Sunday, November 2nd 2025. Presented by O'Steen Automotive Group, Art 'n Motion, & St. Johns Chamber of Commerce.

https://www.pontevedrarecorder.com/stories/73-nissan-z-race-car-to-be-exhibited-at-ponte-vedra-auto-show,150339

With that air filter the way it is I wonder where the float bowl vents went? The one that's there should be connected to the hose from the valve cover.

@siteunseen Our “Forum Librarian Guru” Strikes again!!

I just ordered a pair from Z, I've used silicon rubber hoses before for other gas-related things, they would eventually get soft, but I'm told their's is made for gasoline. I'll do a visual again, looking for vacuum leaks can be difficult, if the engine was running one can use propane that gets sucked up from the leaks and you can hear it in the engine, but this guy won't start yet, oh forgot, need to use new fuel to be supplied directly to the fuel bowls. I'll keep you posted, hopefully getting close. Jim

I agree, that's what I used on all the vinyl and firewall pads. I don't know why I didn't use it on the weatherstrip......I was amazed after 50 years, it just peeled right up and didn't harm the vinyl in any way, still pliable.

I did clean it! First with alcohol, then the 2nd attempt I even roughed up the surface of the weatherstrip with sandpaper, then cleaned it. I even bought another small tube of the 3M super weatherstrip adhesive from Walmart and got the same results. The fact that the adhesive adhered to the paint so good, made me think that it was still good. The hatch weatherstrip I got from Australia had a totally different feel to it. The rubber was more "sticky". It required 100% talc powder to be applied to it after it was glued on, so the painted hatch surface would slide over it when you closed the hatch, until the seal bedded in.

ZTherapy uses silicone nozzle hoses.

Thanks for the link! The one I pictured appears to be the same as the one on the far right of the three pictured by 26th-z. It only has one "hose barb" connection. Thanks Again!

Thanks, Parman. I will be heading out to Menards to get the automotive Goop tube. I don't know what 3M was thinking designing a glue which is black. Clear one makes perfect sense.

I really like this stuff for all adhesive needs: 1 Gal. DAP Weldwood HHR Contact Cement You may have to clean some weatherstrip of its "mold release" before trying to glue it in. A little lacquer thinner on a rag and a few wipes on the surface to be glued is all that is needed. For door weather strips, I use an acid brush, start in the sharp corner at the top, back of the door. You can do it in sections about 18 inches long. Just apply adhesive to both surfaces, wait about 3 minutes, and then press and stick. It is going nowhere after that.

Did you clean the bonding surface of the weatherstrip samples with alcohol (or similar) before applying the adhesive?

Spot The Bot!! ☺️

Hi, I used the automotive version. I cut that precision weatherstrip into short pieces, and did some tests gluing them to a painted license plate. I tried permatex, 3M, and goop. Clamped them down, let sit overnight, the goop was the winner. It could be something in the rubber weatherstrip itself, like silicone or something that did not adhere to the 3M. Or, my tube of 3M was old....but the 3M super weatherstrip adhesive sure adhered to the paint good, I mean really really good, but absolutely did not stick to the rubber. I should have known, the same thing happened to me 6 months earlier when I glued an aftermarket door weatherstrip seal to a 57 ford pickup door I was working on. It fell off the next morning 😆.

Can anyone confirm that this is air filter assembly is from an early 240Z? It looks similar, but is missing some of the inlet/outlet barbs that I think it should have? Could it be from a different Datsun model altogether? I'm looking to purchase these, but want to make sure they are for a Z before pulling the trigger. Thanks in advance for any input!

In all seriousness, I alllllllmost flagged him earlier today before he even ever posted. I think there was about an hour between him joining the forum and his first post. I should have followed my gut and done it. Would have looked like a master bot—spotter. Bonus points for those who see what I did there. Hahaha!

Excellent job reinvigorating a seven year old post!!! You're exactly right, things always come around again!!! Do you have bondo in your roof? How is Jan? Say hello to Dwight!!!

Good point!! 😄😁😆 What kind of car do you drive? Does it have bondo in the roof? ☹️

Nice catch. I read that comment but it was so bland that it was almost invisible. Thought it was a person commenting just to comment.