ecp48's Content - Page 4 - Classic Z Car Club Skip to content

ecp48

Community Member
  • Joined

  • Last visited

Everything posted by ecp48

  1. Use a pilot bearing puller. Two arms slide into the bushing, crank down the threaded retainer and use the slide hammer to pull it out.
  2. san_maru_zed, They look like the 78 280 type relays. When I get home from OHIO (Athens, GA), I will try to scan a copy for you. Ed Palmer
  3. san_maru_zed Based totally on hearsay (Lawyer term), when I was trying to figure out what I had after acquiring the 78 (I had a 76 and had previously owned a 75), a local tech told me that the 78 harness was used for only part of one year here, but was used until early 80 in OZ. If so, the harness would have 3 pigtails for a four pin relay on the passenger fenderwall. The relays mount behind the black bracket (large L shaped) in front of the battery. Two are the small (appx 1 - 1.25" square) base, one the 1 X 2 base. The latter may have five pins, I can't remember and my schematic is not at hand. By the way, the fuel injection relay on the 75 - 77 was on a pigtail off of the FI wire loom near the ECU connector. If you think of any other questions feel free to email. Ed Palmer/ecp48 Athens, Ga
  4. Hybrid Z had a thread running on this topic. I believe the average for a basically stock 280 was 128 - 139, based on several different cars. ecp48
  5. san_maru_zed, What you are up against are the differences between years of fuel injected Zs and 850/maximas. As to the Zs, the 75 - 77 280 is very similar. the fuel injection relay, (single relay) is located in the left side kick panel, at a height which places it behind the dash. The 1978 280Z has an interim injection system. Three relays, all located under the black relay bracket, in front of the battery on the passenger side fender well. It is quite similar in function to a ZX. The 280ZX also has multiple relays, but they are not all in the same place (from memory). I think one is on the right or passenger side fender wall in a recess in front of the battery and two others are on the drivers fender wall toward the front. The 850 Sedan system is quite similar to the 75 - 77 280, (I used an 850 CPU in my 75 280 years ago). The maxima is close to the ZX, but I can't recall the relay locations. In essense the the 78 280Z was a change over system, moving toward the ZX system, which had the 02 Sensor and other bells and whistles. You must look for the relays, which match the harness (year and donor car) you are installing. Good luck. ecp48/Ed Palmer Athens, GA
  6. ecp48 replied to LanceM's topic in Open Chit Chat
    I have an old Century Mig that I bought from Sears in about 1987 (working on an IMSA RS Pymouth TC-3 front wheel drive w/ VW power), welding unibody seams. Also own a Lincoln AC-DC Buzz Box and an Oxy-Acetylene torch. I use all three regularly.
  7. ecp48 commented on Chino 240Z's gallery image in Big Z Photo Collection
  8. Will the struts and springs fit, yes they will fit, i.e.: bolt up. However, if you want to know if they will work for you, Carl is correct, no they won't work. They drop the car to far, in that the 240 Struts are shorter than the 280 Strut and the springs are only going to make it worse. Speed bumps will be a mountain. Hope this allows you to satisfy your friend. Now if they had adjustible coil overs, you might make them work. ecp48
  9. You need to look at the flange on your headers and see if it is the same thickness as the flange on the intake manifold. If they are the same, use the same washer, no special washer is required. The special washers are used to make up the difference, if you have the very thin flanged headers. My MSA 6/2/1 header has the same thickness flange as the intake. My Pacesetter, coated headers have a thin flange but have small tabs welded to it to make up the difference. Neither require the special washers. Examine your header and choose accordingly. ecp48
  10. Jeff, Yes, sent you a PM.
  11. I have a set of front frame rails. They came with my 78 280Z, probably Zed findings from MSA. These are four or five years old, still in the box, which has deteriorated. Some very light surface rust, (unprepared metal and sitting in DC for the last five years). If it interests you, make me an offer. ecp48/Ed Palmer Athens, GA
  12. Phred, As usual Stahl makes a super looking header! I didn't know they made one for the L6 Z. Is there any benefit to mounting the glass packs in the center of the system rather than at the end like the twice pipes? I had thought of installing a resonator in the center and leaving my glass packs at the rear. Any thoughts? The crossover you installed is what I'm planning, only a little closer to the header. ecp48
  13. g72s20 If you look at old catalogs from almost every supplier, Sharpe, BRE, even MSA today; they all had a two/twice pipes system. Datsun Competition listed it as well. Don't have my old Datsun Competition catalog handy, or I'd provide the numbers. The MSA 10th Anniversary edition catalog show them on page 44, 70-78 Z with headers was 15-6030. There were three other parts numbers for various years stock exhaust manifolds. The Datsun system was listed as competition only and came with the glasspacks or straight pipes (from a failing memory). Noise/glass packs and a modern trend toward 2.25 and 2.5 turbo type exhaust systems has displaced their popularity. ecp48
  14. Ed According to the L6 engine builder, you would have 9.82:1 without the .040 shaved off the head. You are probably looking at somewhere in the area of 10.5:1 (quick estimation based on the increase in shaving a P90 .080 on a flat top piston block. (Increase from 8.52:1 to appx. 9.82/10:1)
  15. Try your local WalMart. Revell 240Z @10.99. Most have had them for at least a year.
  16. Tomohawk, It is like a transmission cooler. Appx 6 to 8 inches high. Forms a U bend with fins connecting both legs and mounts off the engine, above the power steering pump on a 5.0. On an F-150 Pickup I had (89), it was larger and had tubing which extended the cooler coil to a position in front of the Radiator on the Drivers Side. You should be able to use the smaller unit and mount it where convenient. ecp48
  17. Hey guy, I have an original NOS set of twice pipes, that I plan on installing. 1.75" pipes, glasspacks are 24" long paired with chrome tips. I know the glasspacks will probably need at least resonators on each pipe in the tunnel area, but has anyone used a crossover. On a V-8, the crossover connection smooths the pulses and usually produces more power. If it would remove some of the reported harshness from the twice pipes, it would definitely be a positive. ecp48
  18. What was the price for the reconditioned L6 Injectors. The post just said 15.00 Core. I haven't tried them, but the site looks interesting. ecp48
  19. ecp48 replied to Zvoiture's topic in Polls
    Born in Milford, Connecticut Grew up in South Florida (south of Miami)(1956-1989) Live in Athens, GA Almost everyone in South Florida was from somewhere else. My wife was one of the few natives I have known. ecp48
  20. People seem to forget on this issue, that there were two different (non-welded) brackets used on Maximas. This matches the fact that there were two different ZX calipers (I have no knowledge of a specific Turbo caliper). In the back listings/strings on this site, HybridZ and IZCC there are a number of articles which highight the difference. Early used the 280ZX caliper for 79 to appx. 80/81. Later used the ZX caliper 81/82 and later. There is some discussion as to whether the break point was 1980 or 1981. I would imagine it overlapped. The difference is identifiable by the backing plate, floating or not. I have the late bracket with the 240SX Calipers, could also use the late ZX or Maxima. [Casting Numbers: Bracket 19C (raised on the upper leg) and DD360 stamped on the lower; the caliper has K36 and it's slider component is K37.] When someone says the rotor won't match up, it's because they are trying to mix and match the early and late styles, ie: the brackets, rotors and calipers must be from the same period. To totally confuse things, the Maxima seems to have made the changeover after the 280ZX did. Further, while the late style brackets use the calipers from an 82-83 ZX, I have never seen a removable bracket on a 1983 or 84 Maxima, and I've looked! (four of them last week, all welded) Be prepared to adjust. There was nothing wrong with the early caliper, it's the late ZX caliper which has been heavily panned on this site and Hybrid Z and can always be replace by a 240SX caliper. The early caliper had problems with the emergency brake connection (from memory). (':stupid:') The following is currently available on ebay. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2477508204&ssPageName=STRK:MEWA:IT
  21. Frank13, I probably wasn't clear. The brackets I am using are the 81-82 Maxima bolt on brackets. They originally came on the Maxima with a caliper which "looks" just like the 280ZX caliper. I bought the brackets with a set fo 240SX calipers attached (standard bolt on). As I said, the only external/visual difference that I noted was the brake line, for which I got the stainless steel conversion pieces from fonebooth.com and the emergency brake connection. I bought KVR pads from Ross Corrigan. The rotors I am using are from the Maxima, as I had them. I am told that any of the late 280ZX rotors, 81 to 83 will work. My original misconception was that the larger rotor from the 84-85 300ZX (4 lug) would work, but they are much to big and only work with the Ross Corrigan (Modern Motorsports) or fonebooth.com aftermarket (fabricated brackets), unfortunately. Hope this is clearer. I verified that the calipers were 240SX by matching the casting numbers! ecp48
  22. 26th-Z, Thanks for the pictures. I was driving back home to Athens, GA from Raleigh, NC early Sunday morning and planned to go to the Mitty, but the weather convinced me to go on home. I flew in from LA on saturday, where I happened to fall into the MSA - West Coast Nationals the previous Sunday. Trip was not planned, but I will take whatever good comes out of "business" travel. Great show. Too bad I wimped out on the Mitty, maybe next year. ecp48
  23. aaron-san The place to purchase manuals is ebay. You can also buy the factory manual on CD Rom from Courtesy Nissan. I got both a CD Rom and a Paper manual for my 78 on ebay, after a number of bidding exercises. From memory, my original 75 280Z manual was about $75 dollars at the dealer (bought in 1979). The '78 280Z manuals have been going for 70 to 100 dollars on ebay. The other year 280Zs have been going for less. good luck! ecp48 ps: I also tried the on line used book sellers without any luck.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.