ecp48's Content - Page 5 - Classic Z Car Club Skip to content

ecp48

Community Member
  • Joined

  • Last visited

Everything posted by ecp48

  1. Frank13 I have not installed them yet. I purchased the 240SX calipers with the brackets. They definitely bolt on. I originally thought you used the 300ZX rear rotors, but have since found that to be untrue. The 300ZX rear rotor only works with the aftermarket brackets, not the maxima. I have lined up the caliper/bracket and maxima/280zx rotors and they appear to work. I will post it next week after installation. The difference between the 240SX and late 280ZX calipers appear to be a different angle for the bracket which mounts the emergency brake cable. I also believe there is a difference in the original brake hose (280ZX vs. 240SX). ecp48
  2. PrOxLaMuS© Yes, 3" 90 degree bend, tube. Should extend from the rubber seal at your AFM to a position in fron of radiator. If you check on ebay, there is a guy who lists one with a K&N Filter. Look at it. The only thing to add is a couple of bolts to attach the tube to the plastic shoe, which attaches the tube to the car (slip fit in to bracket/channel on the car, presently mounting the original air filter. The following link is for an ebay unit for 280ZX, no difference to speak of. Just look at for the picture. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=33659&item=2477076791&rd=1 Good Luck, ecp48
  3. PrOxLaMuS© I noticed a difference in sound, but I think it was just the induction sound, ie: no or little restriction. It reminded me of the difference btween a 350 Chevy 4 Barrel with a stock Air Cleaner, versus the free flow Moroso Air cleaner. If that helps. If you are like most students, it will be a while before you get the turbo, so make the most of it. Install the clean air intake and header. You can always change the exhaust when you get around to the Turbo or the $$$ strike you. Look carefully at the reducer section that joins your manifold to the exhaust system. It is much shorter and tighter than an earlier 280. Very restrictive. You will be pleased with the difference the header and intake will make. ecp48
  4. PrOxLaMuS© In answer to your question, swaged or expanded means the 3" id was expanded to be a slip fit over the end of a 3" Tube. Your local muffler shop will not produce a "mandrel bent" tube. They slightly collapse the tube, creating a smaller ID in the bend. Yeh, the intake by itself may only produce a couple of HP, but when combined with headers and other changes the result is much greater. As someone has quoted many times on this site, "the internal combustion engine" is nothing but a large air pump. Getting the air in is only half the battle. However, as restrictive as the stock intake is, any improvement is a plus. I noticed the difference on my 78 280 and the addition of a new header was an even bigger plus! The exhaust on the 77 and 78 is real restrictive (area between the manifold and the main exhaust, 2 into 1). Much more so than my previous 75 280. ecp48
  5. ecp48 commented on fightyourself's gallery image in Big Z Photo Collection
  6. ecp48 commented on fightyourself's gallery image in Big Z Photo Collection
  7. ecp48 replied to hcb240z's topic in Racing
    Clay, I have never seen "weld in" camber plates. They all seem to bolt in to the modified strut housing. Try Carerra Shocks for a race grade camber/caster plate. MSA also has both a street unit (urethane) or a metal competition style unit. ecp48
  8. ecp48 replied to Hunter21's topic in Body & Paint
    Maybe this will help! http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=34200&item=7900374256&rd=1 ecp48
  9. ecp48 replied to ecp48's topic in Interior
    For what it's worth, the other post I had received (different list), suggested mixing the RIT with a carpet shampoo and applying it with a scrub brush. Apparently the brush causes the fibers to open up and the shampoo floats the dirt away? Supposed to give better penetration. ecp48
  10. ecp48 replied to ecp48's topic in Interior
    Thanks Zron ecp48
  11. ecp48 replied to ecp48's topic in Interior
    hls30.com Thanks, I had someone else suggest RIT dye on another site, but no one has suggested long it will last. I have to remove the carpets, doing some welding on the floor supports and installing a comp. rear bar, so I will give it a shot! Thanks again, ecp48 Athens, GA
  12. ecp48 posted a topic in Interior
    Has anyone done a succesful restore on original carpet? My carpet ('78 280) is in super shape, just faded to that red/brown color from the original black. Is there a good carpet dye out there. I had a previous post I picked up for a VHT product, but it appears to have been a vinyl dye. Thanks, ecp48
  13. ecp48 replied to carrman's topic in Interior
    Dave, I think I responded to your post on the IZCC board, but I ended up settling on an Acura Integra Leather bucket, Method of mounting using the original Z rails is on the IZCC web site, under technical articles. My second choice, was the Tiburon bucket. Long thread on HybridZ. Apparently it will fit well, though I haven't looked at one. I was on my way to buy a set of the tiburon buckets (Black with Gray insert, but stopped to look at the Integra seats and sotpped there. Try Tiburon on the HybridZ site search engine to find the thread. I can tell you the prices were outstanding! Cloth for appx 65 to 85 each in the Southeast. Leather was appx. 100 to 150 each. I will post the Acura seats once the brackets are completd. good luck, Ed Palmer/ecp48
  14. zeiss150 Hey guy it is going to be just as smooth either way with proper tune up. The differential is performance. Higher compression, more Horse power. Also, higher cost of operation due to the need for hightest fuel. I am opting for the the near 10:1 using a P-90 head, cut .080, on a flat top piston block. the biggest difference will be that I am using an aftermarket Cam with increased overlap, which will allow a higher compression without detonation problems. This is what 2manyZs was referiing to, when he asked if you were planning to change cams. (I am also making additional changes on both the intake and exhaust sides to better utilize the compression and cam.) So the real question is: "are you satisfied with a slight increase in compression and horsepower, or do you want more". At this point, it is your call, mainly based on $$$, maintenance and fuel costs. Remember, smoothness will be solely a product of the final state of tune! ecp48
  15. 240Zdragon72/Brian You would do as well with a 240SX throttlebody using the JSK adapter (Juan, Jsk) is on the web and he's a member hybrid Z. His adapter allows the use of all of the fuel injection system components, with the 60MM Throttle body. You will need to relieve the entrance to/throat of the manifold to match the Throttlebody, but it is worth the work. ecp48
  16. The 1979 ZX mastercylinder (15/16ths) is only 39.99 rebuilt at Autozone. I checked Pepboys and Advance, as well, Autozone was best on the Toyota 4Runner Calipers (vented Rotor) as well, 39.99 appx. Pepboys was best for rotors, about 24.99 or 29.99 new, I think they were Raybestos. I bought bothe the 300ZX front ventilated and rear solid rotors. The Zx rear rotors were the same. Used rotors within spec make sense, the mastercylinder is questionable. They tend to build up moisture and corrosion while sitting. ecp48
  17. 240Zdragon, etc., From a very aging memory, I would guess it was a 75-76, non EGR intake with a Weber Big Throat/mouth, whatever, throttle body. And knowing Harry it was all hogged out to the max! I don't think the Turbo intake was commonly available at that time, 1981 probably about May or June. ecp48
  18. So that no one gets led astray when boneyard shopping, the 1981 - 84 Maxima is "rear wheel" drive. Also, be aware that the majority of these cars have welded on brackets. I am presently experimenting with cutting the welds, just to see if it will work. Seems to me a narrow bead on the top and bottom only. Also the 240SX calipers work with these brackets as well. Yes the stub axles have to be pulled, no it isn't that big a deal with the proper tools. ecp48
  19. Harry Gershensen (sp), who owned (recently sold) the "Z Shop" in Kendall (south of Miami, Fl.), had a 77 or 78 running twin turbos in 1980 or 81. It used a two step enrichment). I watched him run in the modified class at the Bay Bottom Crawl. Extremely quick. He was also an SCCA/IMSA racer at the time in a 2.8 powered 240. I later saw him using a twin turbo 3.0 in what was to be a 240SX for SCCA (about 93 or 94). He felt that he got a much more responsive power curve with the twin turbos. At the time he would only smile when asked about peak HP. The car recently came up for sale on ebay and the seller said Harry had retired and another guy bought the motor. Very knowledgeable individual and might part with the knowledge now that he has retired. ecp48 Ed Palmer
  20. Xtra Large for me, but how about a small/XS as well for the peanut sized 5' wife. In her case a Men's medium is a night shirt! What logo are you planning on using? ecp48 Ed Palmer
  21. ecp48 commented on MistressMotorsp's gallery image in Racing
  22. If I'm not going brain dead (memory), 10mm x 1.25 x 40mm long (10.9 hardness). These will fit both a 240Z Hub and the later 280. They are a hair long on the 280, but the best compromise I could find. ecp48
  23. The question really deals with money and how much you want to spend. I am doing the late maxima brackets with 240sx calipers and 1984 300ZX rotors. The late 280 ZX calipers will also work with these brackets, but there is a lot of negative comments floating around as to there durability. Several companies including Ross Corrigan/Modern Motorsports, Motorsports Auto and fonebooth. com all have versions of this. They use a fabricated bracket (Aluminum) and either the 240sx or 280ZX calipers. The Maxima brackets (Cast Steel) are hard to find and harder to remove. modern-motorsports@shaw.ca http://www.zcarparts.com/ http://www.fonebooth.com/auto.html Check the "Z Car Homepage". Home of the Internet Z club, there are a couple of tech articles. The Hybrid Z search engine is down at the present due to band width issue with the host. Soon to be rectified. Good luck. ecp48
  24. Chloe, (8) 10mmx1.25 with 14mm Hex at 26mm long. (25MM ok) (8) 10mmx1.25 with 14mm Hex at 35mm long. (1) 10mmx1.25 with 14mm Hex at 60mm long. thanks, Ed

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.