Everything posted by ecp48
-
One of our own in bad accident
Accidents happen, but they sure do modify your thoughts and approach to life. Happy to hear you are home and getting better. ecp48
-
Head Changes/Compression
Thanks, It gives me a statting point. I think I'm going to have to invest in a burette. Ed Palmer
-
Speedometer gear
Tanny, I had a 75 with the four speed, but I didn't change the gear on it. However, I installed the rearend from a ZX 2+2, which is a 3.88:1 and used the gear from the 2+2 tranny in the five speed I had swapped in. I don't think there is any difference. I don't remember the color. Try the 2+2 gear as 3.88 vs. 3.9 is pretty close. Let me know hat you work out, because I am putting in an 83 2+2 Rear end in my 78 280Z fairly soon and will need to change the gear. ecp48
-
Head Changes/Compression
javascript:smilie(':stupid:') I have noted a number of comments on the site about not raising the compression beyond 9.0:1 due to fuel considerations. In the past, with American V8s, the rule of thumb was, that you could raise the CR by one point if using an aluminum head. Why doesn't that work with a Z head (L-6)? Further, does anyone have a rule of thumb for how much the compression goes up on a N42 or 79 head per thirty thousands (.030) cut/milled off head surface? I read on another site, that an eighty thousands cut on a P99 would raise it to appx. 10.0:1, but this is the 81-83 head with the larger combustion chamber/raised deck (8.3:1 to begin with). Also, when using a high lift/longer duration cam on the L6, I am told you can go with a higher compression. My last experience with Zs was a 1975 280Z Coupe, only Mod was a header. (A big throat was beyond my budget at the time. Starving Student with a Formula V habit. Amazing how far the GI bill would stretch!) (2nd in Class, beat by a 240Z in the 1980 Bay Bottom Crawl.) Anyone have any thoughts on the compression issue?
-
Yellow Lowering Springs
Thanks for the help, I think I remember the Mulholland springs being red, had a set 20 years ago! Thanks again, ecp48
-
Yellow Lowering Springs
Anyone remember who made yellow after market springs. What the drop was etc. ecp48
-
Mass air for 280Z
Super_ Ford, Did you get into this? Was it an improvement? Ed Palmer
-
280z Wiring Diagram
Send me an address, which do you need or both? Ed ecp48@yahoo.com
-
280z Wiring Diagram
The 78 280Z has two different wiring harnesses. I found out through trial and error. The post 5/78 builds use a harness that is similar to a 79 280ZX, 2 fuel pump relays and a separate fuel injection relay. I have this schematic, not in electronic format, but could send it. I was informed by a Datsun Technician, that the others, 75 - 78 are almost the same, for all practical purposes. I have a factory 75 schematic as well. Ed Palmer
-
need info. installing fuel inj. in 240z
Hi, I was considering this myself and did some research. The harness for the fuel injection will work, as long as you use all of the relays, etc. You need to open the requisite hole in the firewall to bring the ECU into the passenger compartment and install the Fuel Injection/pump relay under the drivers side dash area. The pump bracket will fit. I know you need the 280Z tank for the fittings. Breather line, pump supply line and line from pump to injectors and need a second fuel line for the return to the tank. I liked the idea because you get the light body with the smooth fuel injected engine. Didn't procced because ther was too much rust in the early 260 I was going to use. Hope this helps a little. Ed Palmer
-
240 Struts on 280???
Has anyone tried using a 240Z strut on the 280Z. I have struts from a 72 or 73 with Yellow lowering springs. I guess the question is, will it lower the car too much!javascript:smilie(':stupid:') javascript:smilie (':stupid:') Ed Palmer
-
78 Z fuel Pump Relay
Apparently their was a change on cars built after 5/78. they have a system like the 79 280ZX. There are three (3) relays replacing the original one. the first is a fuel injection relay, 2nd is a Fuel pump relay (1) and 3rd is a fuel pump relay (2) or control relay. I got help from a shop owner, former Nissan Factory Mcechanic. Mitchell had the schematic in their wiring update for 1978 and the dealership had a 1979 ZX manual with the test procedure. According to the mechanic (Bob, owner of Autotek, Athens GA), there was only a few of these (comparatively, imported. Most were sent to Australia where the 280Z lived for an additonal two years (1980). He remembered only one at the local dealership and didn't think the 1978 Factory Manual even included this change! Thanks again, Ed Palmer
-
78 Z fuel Pump Relay
Thanks guys, Will try to pin it down. I noticed the click on start up from under the relay bracket under the hood, but the manuals didn't id it. The 75-77 all show a two part relay, fuel injection and fuel pump in one housing. They apparently split it for 1978. Thanks again. Ed Palmer
-
78 Z fuel Pump Relay
Wher is the relay for the fuel pump located in a 78 280Z coupe? My 75 Factory Manual is little or no help, says side dashboard, drivers side. the illustration in the 75 manual and Haynes is almost identical but doesn't locate it. Help. Thanks, Ed Palmer