Open Discussions
Open discussions about the early S30 series issues and topics.
8,764 topics in this forum
-
- 7 replies
- 1.5k views
Just wondering if anyone is autocrossing their Z? I'm interested in the setup you have and the pros / cons of the performance.
Last reply by 2ManyZs, -
-
- 1 reply
- 2.1k views
Hey Alan, If you are on this website, well I just randomly got these pics fwd'ed to me from a friend of your FP autox Z and... wow that's one bad arse lookin car... Hey who needs B-pillars anyways.... Can I get a ride? Provided you even have a pass seat left? -e
Last reply by Zlishous, -
salvage title 1 2
by Franklin- 12 replies
- 2.2k views
Found an interesting 240 but it has a salvage title. Current owner says he bought it this way and the previous owner said "theft" recovery". What do you all think? It's about $1k and runs but needs a little work. Looks ok though.
Last reply by Franklin, -
- 2 replies
- 1.8k views
I have a monza header for my 72 240z that has two separate exhaust pipe outlets. Each exhaust pipe outlet serves three cylinders. Has anyone installed a dual exhaust with custom bent exhaust pipes?
Last reply by ZmeFly, -
- 2 replies
- 1.4k views
Anybody know a good place around Melbourne for interior parts for the 240- I'm on the hunt for a dash cover but after that I need new locks, a new center console and possibly some outher little nick nacks, Any advice? R
Last reply by 2ManyZs, -
- 8 replies
- 2.6k views
Hi all. I am new to the Z community, as I have just purchased a 1972 240Z that is quite the basket case. It is all original, but has much rust, and a blown head gasket. At least I got a good deal... $300 for the whole thing, and it would still run, and even idle!!! I have the head off now, and am getting it machined smooth. I plan on just getting it running for now, and then tweaking it later. I can't wait to learn how to tune and set the round top SU carbs!!! Here is a question. What type of welder should I get? I would like one that is 110V, if it could handle body welding, and perhaps some frame welding... 208/230V would be ok if that is what it takes. I hav…
Last reply by madmike, -
- 1 reply
- 1.5k views
I'm looking to replace all my worn bushings on my car and I was looking thru a catalog that had an option for urethane control arm bushings (no adjustment) or a camber bushing set (adjustment of 1 1/2 degrees). I'm wondering if the camber bushing set is worth the trouble over upgrading the basic bushing set. It seems the camber set is good for more adjustment and also bad because its another thing to adjust on the vehicle. How much does tire size play in this decision? I'm sure use of the vehicle comes into play as well. I'm not racing just looking to have fun on the weekends. I have a similar question regarding tension/compression rod kits the aluminum socket and an…
Last reply by emccallum, -
- 2 replies
- 1.7k views
This was sent to me by Summit Racing. This would be a terrable thing to happen. Your hobby is in danger! Proposed U.S. government legislation, U.S. Senate Bill S.1766, would allocate federal funds for state scrappage programs for vehicles more than 15 years old. In the process, it could threaten the very existence of our hobby by: *Destroying 1960s and 70s era musclecars *Scrapping 1980s performance vehicles like Mustangs, Camaros, and Corvettes *Eliminating many non-performance vehicles which provide an invaluable parts source Take a stand for your rights--and your hobby--by letting your U.S. Senator know how this bill will directly affect you. Log onto our webs…
Last reply by 2ManyZs, -
- 5 replies
- 1.6k views
My main throttle linkage and slave throttle linkage doesn't have any play between them. I couldn't locate locate any adjusting screws to reintroduce play between the two. Does anyone have any ideas?
Last reply by Royce, -
- 2 replies
- 1.6k views
What type of aloy-wheels kan I use? I look for 7,5`16"with ET 10 to 15,and, can I use 7,5 at f ront, and 9" on the rear on a original car . second : I need a new dashboard. where do I get that from,(the best there is) , and I also want to stiff up my car ... shocabsorbes,springs etc etc. Here I go short with my english so help try to understand what Iam lookig for thank you all yours Hans-Eric;)
Last reply by Zlishous, -
- 1 reply
- 1.7k views
Anybody got one they would sell?
Last reply by zfreak72, -
- 0 replies
- 1.5k views
Hi All, All are invited to drop in to see a newly created Z Car Project Preview Showcase to preview the back log of featured custom Z cars, projects and tech articles in preparation at ZPARTS.COM. I think you will find many of the previews of great interest. Apparently, the index page has become quite popular since published because there is such a wide diversity of surprising cars, projects and quality photos to review there. Hope you'll drop by. Comments and suggestions welcome, but please do not request more photos or technical answers to your questions. Hopefully, completed articles published later will satisfy all you wish to know. Enjoy- Eric Neyerlin - ow…
Last reply by Z PARTS,
-
Recently Browsing 0 members
- No registered users viewing this page.