All Activity

Damn- 5 year update ?!!! I’ve been thru several induction systems including Protunerz . Now running these FAJS . I’d say this package runs better than anything I’ve had on this engine . The Protunerz ran good but I think the runners were too short and fat . I did manage 35 mpg driving to the Woodward cruise last year with that manifold - that’s at 80 mph -windows down! I’ve been blown away that I’ve been able to get these ITBS tuned in so well . First start it idled at 750rpm . I run the cable linkage which like any linkage has to be dialed in correctly . I was always told that when the engine gets hot the idle rpm will climb , but I’ve got these to idle better than my single plenum . These are 45’s . The stacks are 75mm long . I have not dyno’d this package . Looking back at this thread I can say I was running too much ignition timing . Also blew up #6 piston . I run 28 degrees WOT . Finally got smart and made det cans to wear while tuning . I had some pinging at peak torque . I still run a lot of timing at light cruise - thus able to get lean cruise . I think I got high 20’s MPG going to ZCON . I was still tuning on the fly . Though I ran triple Mikunis before - I didn’t think I would do ITBS because I thought they would be to challenging . They are a challenge but glad I did it

You've already quoted the names behind the business. Perhaps you don't read your own posts? "...just selling car parts..."

I’ll have to recheck my setting for my stroker but I think my fan comes on at 185 and goes off at 180 ? I have an ECU so it turns on my fans at a lower setting at 185 and full speed at 195 .

Here's another one on Hagerty Auction closes in a few hours.

Thank you for that information that's great. I personally like the body lines but if done well it looks great. This one was done in the '80s and I'm sure it looked great then but it's had a hard life since.

Naaa. I'm just trying to figure out who's running this new Z car parts store. And, as usual, you're ignoring what was written and projecting your own thoughts in order to create an argument. These guys clearly state that they intend to restore the cars to how they were as they as they left the factory. SpeedRoo pointed out some things that were not that, but you just ignored that reality and chose the argumentative path instead. Typical. They're just selling car parts, in the end. Nothing wrong with that, but nothing noble about it either. The Z car market just looked like a profitable one. Good luck to them. S30 World - The place for the S30 familyS30 World | Your online Datsun and Fairlady Z parts shopS30 World offers a selection of premium products designed to enhance your Datsun. Explore our quality parts to restore your Datsun or Fairlady Z.

Last thought... I think that welding the buckets to the fenders and removing that seam line is a great improvement to the looks of the car. When done right, of course.

The headlights are removed from behind. Inside the wheel well. So yes... You can remove the headlights without removing the bucket. In fact, there is no "maintenance" reason to ever remove a bucket. Only ever removed when doing bodywork on the car. It is my theory that the only reason the buckets exist in the first place (instead of making the fender and the bucket all one piece) is that Datsun could not manufacture the fender that way. The metal is not able stretch and shrink enough to make that possible. I think that if it were possible, they would have made it all one piece from the factory.

No. That would be simulation. See how this stuff works? You're already dancing with us on the head of that pin I mentioned. It's getting mighty crowded... Some level of scrutiny is fair, but I can't remember you drilling down into to any other commercial business and their work to this extent. The comment above just makes you look foolish and parochial. You're calling into question the skill of the people who performed work that is clearly to a high standard - visible to anybody who looks at the photos on the S30.World platform - let alone their bona fides? I think they have a right to be proud of the work they've done. Did it ever occur to you that there might be quite a lot happening in relation to these cars which has sailed majestically over your head while you weren't paying attention?

im working on my 280z project car and tackling lighting currently. I went to remove and check the wiring for the headlights and one of the previous owners in the 80s decided to WELD the buckets to the fender... He did alot of body work to make the car have very minimal body panel lines and used bondo to smooth everything out. i thought that was just it until i took it off and its stich wedled... poorly at that. ill get them off but not right now. Can i replace without removing the bucket?

Yeah, Im not convinced myself. This is their latest youtube video featuring the shell. As Alan mentioned above at the end of the day a Datsun with a body made in China isnt a Datsun anymore!

Thanks for the heads up. I will double check the seat mount location next time I am out there. I was thinking it might be the picture angle but won't hurt to check. Thanks!

Easily fixed at this point.

The inner rear seat mount looks to be in the wrong place to me. You may want to have them double check.

@Mike As the title of this thread suggests... It's hammer time. It's time for you to wield the ban hammer. Wield it like Thor. ☠️ *If you wield a tool or a weapon, you handle it effectively. Picture a gallant knight wielding a sword or a skillful chef wielding a whisk. Or picture Thor. Or Mike.

I have high confidence that Ellison is friends with Patel. In fact, I'm pretty sure they were both born in the same software lab.

But a conventional rotisserie makes working on the rear of car and the nose of the car really difficult

Pad in use. Nothing new in terms of any work on the Z. Had a carport built Weather still OK, so I've been driving her around as much as possible

I'm not convinced that this is 'the real deal'. Consider what KF Vintage offers in the way of replacement panels. It's a pretty extensive list, but when you put them all together your still missing (rough guess) 33% of a complete unibody structure. Is anybody really going to tool up to produce the Z's (complicated) A-pillars? And what about the rear floor and rear frame rails? And the (complicated) front cowl structure? And the (complicated) rear hatch sill structure? My guess is that we're looking at a KF Vintage-like collection of replacement panels being bannered as a replacement unibody structure.

The 'rotisserie' set-up is intriguing. It looks like it may do a better job than conventional units when it comes to keeping the unibody structure unstressed as it goes through rotation, but... it looks like a right PIA to cut and install all of the necessary support links. In addition, the roll-over hoops are in the way all the time, whereas a conventional rotisserie has no such blockages.

Yeah, the rotisserie is pretty cool!

Be patient, They are customer friendly and will get back to you. If your that concerned call them.

Amazing what hides behind layers of metal….those repairs look nice. What kind of rotation device is that? I really like that.

I wonder who the "restorers" are. They seem very proud of their skills, but they really haven't been around that long. Since 2019. Apparently their marketing manager was born in the back of a Datsun. https://s30.world/masterpieces "S30.world launches “The Masterpieces program” A celebration of Nissans S30 platformA limited-run of factory-correct restorations of the iconic Datsun 240Z will become available, with the first one to be sold at auction in the United States on October 23rd 2025. This unique program is focused on the full, factory-accurate restoration of Datsun 240Zs, also known by the S30 chassis code, to a level of detail that makes them identical to how they left the production line over 50 years ago. Each vehicle in the Masterpieces program keeps its original exterior and interior color and undergoes a complete, ground-up restoration. The process is guided by an obsessive commitment to authenticity, where every component is either restored or remanufactured to original specifications. From the expertly built drivetrain with its matching numbers engine to the flawlessly restored original interior, right down to the smallest original equipment fasteners, nothing is overlooked. “No expense or effort will be spared to achieve this peak level of quality,” says Chris Visscher, founder of S30.world. What truly sets these examples apart is the craftsmanship applied to the bodywork. Every shell is meticulously returned to its original condition with such precision that no trace of welding or repair is visible, even under close inspection by the most trained eye. All spot welds are recreated exactly as they were applied by the factory, matching both the original pattern and technique." https://s30.world/our-company "In 2019 Gustav Oplasnik and Chris Visscher decided to join forces. The desire to do the best possible restoration with an S30 was and still is our passion. The foundations of S30.world are passion, knowledge, craftsmanship, determination and cooperation. Today we are able to do the best possible restorations on S30s and the time has come to make this available to others worldwide as well. Our next goal is creating an international platform to promote the love for S30s, our restorations and the parts we sell. To make that happen, Florian Steinl became our marketing and content manager. Florian shares the same passion for S30s as we do, since he was born in the back of a Datsun."

Recreating the various oddities/imperfections that happen during the factory assembly of the car would be a restoration. Removing those inconsistencies, like the overspray, would be "perfecting", in my opinion. Removing the stuff that they think doesn't belong. It will be interesting to see what types of finish they used on the hardware. Will they use what appears correct, or what would be "correct" for the time of manufacture? How does one tell? Apparently this is the first appearance on the market of one of their "restorations". Kind of surprising how many they have. And why are they are selling?