mdbrandy's Content - Page 21 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. Yup. I just like to hear myself type! Some clutches lock up all the time, and then you get the airplane sound effect as you accelerate. Mine (on my '78) currently won't engage at all, and thus I overheat if I sit in one place for very long. Got to get that replaced now that warm weather is here!
  2. Here's the description of the fan clutch's operation out of the '78 factory manual.
  3. The fan clutch works on both RPM and temperature. It slips at higher RPM and at lower temperature. It will always spin some. So, if you are idleing in traffic, it will engage as the air coming through the radiator gets hotter, and slip some as it cools off. If you rev the engine sitting in traffic, it will be engaged due to the temperature, but will then slip some as the engine speed rises. As the car starts moving, the temperature of the air moving through the radiator drops, and thus the clutch starts slipping due to lower air temperature, as well as the rising engine RPMS. I think it's mostly supposed to disengage over about 2500 RPM, but it will always turn some.
  4. My manual is dated 15th January 1970. On page 10, the knobs look square, and there was something (now gone) glued over part #27 (Throttle Control Lever). On page 13, bottom right, the paragraph and picture about the throttle lever has a piece of paper with a picture of a 240Z glued over the top of it. Two pictures on the bottom center and right of page 15 have paper glued over them that show the choke area WITHOUT the throttle lever. Same on bottom right of page 16. The picture on the upper left on page 17 looks like it wasn't ever covered, and shows the throttle. And in the index (page 44), the entry for "throttle" has a piece of paper glued over it. Obviously, it didn't take Datsun long to take the throttle directions out of NA-bound manuals! Oh, and all the knobs except on page 10 look rounded.
  5. Mine has paste-over edits over "something", but I don't remember what. I have the manual at home, and I will dig it out and look tonight or tomorrow.
  6. I haven't looked at my handbook since I bought the car a year ago (the 11/69 240Z), but I remember those pieces of paper stuck over something. I didn't know enough about the car yet (didn't even know what a hand throttle was!), so I don't know what they were covering. I'll have to dig it out this weekend and see...
  7. ROFL ROFL One of my kids just got a hamster - thanks for the warning!
  8. Don't know where you're getting your info, but NA cars have their engine block numbers on an info plate on the car, so you can certainly tell which block went with the car. Not the head, however. And there've been many discussions on model years - seems to come down to what it was originally registered as. Which varies over the years. There is no strict cutoff. My 2 cents.
  9. $4000 for my 1978 280Z about 9 months ago. CA car with "no" rust, all original, well maintained, 118K miles. A little much, but really about $3200 considering I'd have had to pay $800+ to get a CA car shipped here to IL, and that's about the only place to find one in as good shape. $3000 for #215 14 months ago. Mostly original, including a few really old, original 1969 bits that are hard to find. Has rust issues, though. Probably about $2500 in NOS parts purchased for the restore so far. Long way to go...
  10. Just make sure to file away this business in your memory, and refuse to give him any business under any conditions.
  11. mdbrandy replied to Zvoiture's topic in Polls
    Grew up in the cornfields of Decatur, IL. Then spent 7 years in Los Angeles at UCLA in grad school - 2250 miles from IL. Then 5 years in South Carolina (first real job) - 900 miles from IL. Then 7 years in Maryland, north of Baltimore - 725 miles from IL. Now in Champaign, IL - 45 miles from home. Looks like I spent most of my time circling the country back to central IL!
  12. I was working on my '75 280Z many years ago, and when I tried to start it, it smoked, choked, and generally wouldn't run. Took me a while to find, but SOMEHOW (I never figured out how), I had sucked coolant into my air flow meter, and there was coolant pooled in the bottom passages. Cleaned that all up and it worked fine again. Don't remember what I was actually working on at the time...
  13. I lied. When I left work today, premium was $2.14
  14. $2.04 for premium here in the corn fields... That's for the real stuff; gasolhol (that I don't use in the Z, but is very prevalent around here) is a couple pennies cheaper.
  15. I second the motion! I can't make it to CA, but I could make the East Coast!
  16. That's cool; I was just noting that I think they were the original ones in the thread. The price is the same, and it's Bob Zola's (rzola) auction. :classic:
  17. I think that's the one that abas noted earlier in this thread.
  18. I try to keep up with all the new Zcar oriented e-bay listings, and I didn't see them. I would have snatched them up in a second, just like the last set went in a matter of minutes, apparently.
  19. I don't know of any registered as 1969's (there may be, but I don't know about them), but a couple of us on this board have cars BUILT in 1969.
  20. Rats! I've been looking for those seals for over a year now. I refuse to remove them from my car until I have replacements, as I figure they'll not fare well if I do. I would like to remove them for painting in the future... I usually watch rzola's auctions closely, but I missed that one. I would have grabbed them in a heartbeat.
  21. Let me take a stab at it: When the TC rod moves up and down, the threaded end "pivots" at the frame end. When controlled with rubber bushings, the up and down pivot movement just deforms the rubber with little resistance. With PU, the rod has MUCH more resistance at the front bushing to deforming the PU, and thus tends to bend more there, particularly right at the "step" which should act as a stress concentrator. With the AL cup/delrin, you now essentially have a pivot cup there at the front of the frame connection, so there is very little resistance to the rod pivoting up and down. The idea behind the harder bushings is to keep the rod from moving front-to-back, and the up and down resistance is a side-effect. The PU compresses much less than the rubber, so the front-to-back resistance is much higher at the expense of the up and down resistance increasing as well. The cup/delrin method gives you very little front to back movement with decreased up and down resistance as well, so the rod doesn't bend at all. So, racing guys, is that a reasonable explanation?
  22. Nobody's mentioned Chloe at MidwestZ yet as a possible place to get said part. She's gotten a number of things for me that no one else said they had or could get... www.midwestz.com
  23. Hey Kats, is your valve cover actually signed by Y. Matsuo? Looks like it from a pic on your new site...
  24. Now THAT would be a very bad thing :dead: ! Do you remember where you read it? I just ordered a Poly bushing kit for my 280Z, and I'm looking for any and all info before I mount it... Thanks.
  25. Yes, that actually looks like the one in my '78 280Z as well. It's interested me that they put the antenna rocker back on the right side. So, my '70 240Z and my '78 280Z have the same antenna rocker position. The 280 is AM/FM and the 240 is AM only.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.