Zed Head

You should put your videos on youtube.

So, what, in detail, does the tach do and not do? Does the needle twitch at all when you turn the key on or start the engine? These old tachometers fail often and in many different ways.

I found an old thread. Pretty much original owner. So, external regulator, old alternator. The VR's go bad eventually, but usually go high voltage. Might just be a bad alternator. Could even be a bad connection on the back of the alternator. Pull them off and clean them up and see if things are better. You'll need a meter like SteveJ says. This is a sign that there's no alternator current -

Can't remember what car you have. and if it's been modified. Things changed over the years.

The prices are trending up. That 300K one really screws up the resolution. I filtered it out. https://bringatrailer.com/datsun/240z/?q=240z

Both of those local coils would probably work just fine. That's a wide spec on the Duralast coil, but it will probably be in the middle at about 1.5. Even if it's a little bit low, that's not a huge difference. Maybe a little extra heat but worst case it will probably just last 50,000 miles instead of 100,000. I'd buy one of those two coils and just use it with your ballast resistor. You'll probably want to check the size on that older Ford/GMC coil if you use that one, it might not fit well. But it should work with no problems once you get it mounted. If you have a meter you could take it to the store and verify primary resistance before you buy if it worries you. Secondary is not as important for longevity, I wouldn't worry too much about that measurement. Just for fun - https://contentinfo.autozone.com/znetcs/psb/en_US/2/0/27/c831_coil_specs.pdf

I never did but probably should have. I think that I used to over-torque my aluminum wheels and was distorting the rims at the seat, squishing it there. The lug nuts used to get stuck in the holes and I'd use a rat tail file to open them up a little. Probably Not Good. Now I have a Ford truck that specs 150 ft-lbs per nut on steel rims. So I bought a wrench and used it. That's a lot of torque.

https://www.gorilla-auto.com/replacement-keys "A Wheel Lock Registrations Key is required to identify the unique key for all Original Gorilla Wheel Locks, X2 Locks, Gorilla Guard or Small Diameter Wheel Locks. Replacement Small Diameter Lug Nut and Hex Lug Nut Sockets can also be ordered using Key Registration Number or Part Number stamped on your Gorilla socket. Why do I need my Wheel Lock Key Registration Number? We are the leading wheel lock manufacturer for good reason, your unique wheel locks and key are nearly impossible to identify through simple visual inspection. Your unique key/lock combination is one of thousands of possible combinations which means your investment is protected."

It's done by computer, and it's not a mold, it's a milling machine. What good is a lock if one key fits many of them? That would be insane.

You must have good eyes. Can you share the photo? Hope it works...

How do you know? The splines are of varying width. It's not just the number nine.

Nissan's 240Z ignition wiring is kind of confusing. If the diagram is correct it's an odd parallel circuit with two power wires to the tach. One through the resistor and one direct. One must be Start and one must be Run. Anyway, they both end up as Black/white stripe at the coil positive. Green/white stripe at the tach gets powered either through the resistor or directly. The diagram is confusing because Run is Black/white stripe at the switch, then converts to Green/white stripe after the resistor, then is back to Black/white stripe after the tach. So, at the tach Green/white stripe should have power during Start and Run. If you test both and only one works you might find that the junction of the two is no longer joined. I think the above is correct I rewrote it a few times...

Might not even need nine. Get four or five prongs to fit some open spaces. He'd need a good grinder though. A cutoff wheel and a vise would be about right. Of course, the socket could explode when he tries it depending on how tight the nut is. (pssst...SteelStick)

Popular problem. Might find something in here. https://www.zcar.com/threads/headlight-combination-switch-repair.311982/ https://forums.hybridz.org/topic/103936-my-headlight-fix/ https://woodworkerb.com/home/datsun-240z-rebuild/datsun-240z-multifunction-switches/

Seems like that should work, physically, but also shouldn't work, theft-wise. Kind of defeats the whole purpose of locking lug nuts, and it's faster. Edit - the caliper will need to come off with the assembly, I think, because the rotor is bolted to the hub and the spindle will not let the rotor drop out of the caliper. So, a little more complicated than it seems. Not as quick and easy as I had first thought. Actually I had thought of it initially but convinced myself it wasn't necessary. Wrong, I think. I haven't worked on front brakes for a while. Can the caliper bolts be removed without removing the wheel? Not sure they can. Show stopper... It's the best idea yet. You'll need the key code for Gorilla. Good luck with that https://www.gorilla-auto.com/gorilla-locks

Just remembered that one reason the switch gets so hot and damages the solder joint is because the contacts get pitted and burnt. You really need to take it apart and inspect. I went through a similar situation on my 76. Resoldered them but they eventually fell apart again. Resoldered and added relays and they only see relay current.

A longer cheaper one. The long punch is very useful, I have this set. I still think the SteelStik has a chance. https://www.harborfreight.com/12-piece-punch-and-chisel-set-66337.html

They probably went out of business because the design worked so well that if you lost the key you were screwed until you could get a new key. If you had a long drift (aka drift pin) and were handy with it and the end was shaped right you might be able to turn it that way by pounding on a projection. But, any slips and you're gouging the rim. https://www.grainger.com/product/4RPL7

Kind of looks like split steel meant to flare out and grip a nut...

Can you post a picture from the side? A person can see the square shapes at the bottom but they don't look very deep. Sure does look more like a cap on a nut. Have you tried grabbing it with Vise-grips and pulling it off.

This will work if you give it time to cure to full hardness. Are you sure it's not a 10 spline? https://www.brandsport.com/bmcc-79241-1.html Or 8... https://www.brandsport.com/search-results.html?query=+Spline+Lug+nut+key%2C+Wheel+lock+key+&x=91&y=23

https://www.harborfreight.com/high-visibility-socket-adapter-set-4-pc-62851.html