mdbrandy's Content - Page 36 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. I have the hand throttle. The stupid PO removed the cable, and lost the plastic handle, but the actual lever is still there. Attached is a pic of what I had when I bought it. The second lever knob is actually a second choke knob that the PO had on the lever. BTW, anyone know what picture is on the knob that the hand throttle would use? Thanks.
  2. Anybody know anything about an N33 cylinder head, and what it might be good for? (specifically 11041-N3302). Thanks.
  3. Look up kmack on this site. He builds them. He has a web site talking about his car and the rotisserie: kmack
  4. Macpherson is the type of suspension - i.e., our cars have "Macpherson strut suspension". (Actually, I think they are somewhat different than a true Macpherson strut, but we call them that). You would have to give the brand of cartridge to allow us to compare anything with the "Tokico" brand cartridges. Your store is probably quoting you for generic type stuff like "Monroe" or "Gabriel" or something. Not performance cartridges. My 2cents.
  5. Victoria British sells the Normal Tokico Gas catridge for $74.95 each in their newest catalog. The Adjustible Illimina's are $145 each.
  6. Ah, but the key is, that on my beast, there was no "unbolt and replace" for much of the work. Floor pans, rockers, etc., with quite a bit of custom patching. I would have paid the $$, but no body wanted it! They could make more unbolting other people's fenders. I am finding out that places where a "restoration shop" fixed it up 12 or so years ago, they did a really poor job in areas that weren't just cut off and replace - front and rear of the rockers, etc. I may be better off doing it myself anyway . Thanks.
  7. Make sure you can find a body shop to do the work before you make your plans. Here in the cornfields of Illinois, none of the 10 bodyshops I talked to wanted much to do with my car. They are insurance, replacement shops. Two places said that they might be interested, but they were too busy now, and my job would take a backseat to more lucrative insurance work (at least they were honest!). They told me to come back in six months and they'd see where they were. Thus, my purchase of a welder and practicing to do my own work . So far so good, but I've got a lot of work to do...
  8. Answered some of my own question - they're in Jasper, IN! :stupid: About 200 miles Southeast of me. Or they appear to have a branch in Chicago, too. They look like a REALLY big operation, though, that doesn't necessarily specialize in any specific type of engine. Who's had experience with them.... ? Thanks.
  9. Being quite close to Indiana myself, where is "Jasper Engines?" When I get to the engine, I'll be looking for someone that knows L series engines... Thanks.
  10. Did you try asking the people at Banzai?
  11. If you have an early type I '71 240Z, then they would be the brackets for the toolbox knobs for the plastic toolbox lids that go behind both seats.
  12. Interesting. I wonder why they say it doesn't work? I'll have to investigate the circuit when I get into it. Are you sure the tach in your car was original? Thanks.
  13. Great! I take it that you like the results? I ask mainly since I picked up a 1980 280ZX distributor, coil, and E12-80 ignition module for $71, and I was hoping it would be a good choice. From what I have read, it sounded like it was. Essentially just a drop-in ignition system-wise? The Zgarage article indicates that you can't use the 240Z tach, and have to go with a 280Z tach, but since I have a 280Z parts car sitting in my garage :classic: , that seemed not to be a problem either. Anyway, any tricks or things I might not know about beyond the Zgarage article would be appreciated. Thanks.
  14. Anyone have experience dropping a 280ZX distributor with the E12-80 ignition module into a 240Z? Zgarage tells how to do it, and says it's a good swap, but I was wondering if anyone on the list has one... Thanks.
  15. Thanks, I can't think of any reason why either, but there might be something. I'm picking up an NOS crossmember on e-bay for $30, so if it isn't right, maybe I can find someone with a 280 that wants it. It LOOKS right, but there may be some suspension point mounting differences or maybe the rack mounts differently. Anyway, not much invested if it doesn't work out. Mine is intact, but very rusty and has some dents in the bottom from inappropriate jacking or hitting road hazards. Thanks.
  16. Anybody know if the front crossmember from a '76 280Z will work on a 240Z? Thanks.
  17. I'm 42, and live in Champaign, IL. Wife, three boys, one huge dog. I have HLS30-00215 (11/69) and currently have it down to the bare shell restoring it. I do engineering supercomputer simulation research at the University of Illinois (www.csar.uiuc.edu).
  18. Thanks, Marty. I think you're right - I was just looking for people who might have done it - like you :classic: . My parts car was going to be a real car until I let it sit and rust out for 8 years. Now it is mechanically OK, but VERY rusty, and as a species that is not as desireable as the 240Z that I found this year, I'm going to canibalize it. I'm going to use the 5 speed, and some other stuff, like hopefully the knuckle arms on the 240Z. I'll keep the L28 and see if I can build a hot-rod 240 at some later time from another body shell or something.
  19. Question for the experts: When I rebuild the front end on my very early 240Z (11/69), it is my understanding that the ball joints that fit the early knuckle arms are NLA, and that I have to either ream out the existing arms, or replace them to use available joints. Now, I have a '78 280Z parts car sitting here in the garage to use as I want - can I just take the arms from it and bolt them onto my 240Z struts? Is that all that is really required? Thanks!
  20. I've been on the IZCC list since about 1997, but now I barely have time to read their digest, 'cause I'm always on this site!
  21. There's another current thread (http://www.classiczcars.com/forums/showthread.php?s=&postid=51424#post51424) where I posted a picture of a wheel cylinder with the lever on the car that might help you visualize what needs to be done to turn the adjusting wheel. It's a pain. I did it without drilling, but that sure would have made life easier!
  22. Toward the center of the car at the bottom of the wheel. Here's a pic of the drivers side on mine. Note how the serrations on the wheel will "catch" on the bar at the bottom if the top of the wheel would turn toward you. Thus, it will "click" over the bar and adjust the brake if the top of the knurled wheel would turn away from you. So, to loosen the brake, use one screwdriver to push the lever arm down, and another to push the BOTTOM of the wheel AWAY from you, toward the center of the car. Hope that makes sense. Note that these are really early wheel cylinders too. There are some changes over the years, but hopefully a '71 will be similar. Good luck.
  23. Thank, kmack. I'll probably buy a bearing puller and one or more brass punches - just because I can. New toys. When I tear the transmission down, I'll replace every bearing and seal I can. That's what I'm doing with the rest of the car. Every piece of rubber, every seal, every bearing, every u-joint that I can get a replacement for will be done. I'm looking to essentially have a "new" z-car when I'm done (or as close as I'm ever gonna get :classic: ). And I'll take MANY digital pictures, and maybe even video the teardown since I've never been inside a transmission. Thanks!
  24. I think I've got all that except the bearing puller (I have a gear puller - would that work?) and a brass "drift punch". I tend to buy the tools I need to do a job if it will save me as much or more $$ than the tools cost, or if I might do it again sometime, since then I have the tools. Sounds like I'll spend a winter weekend taking apart a 5-speed and seeing what happens! Thanks.
  25. Are there any special tools you need to rebuild a manual tranny? Pullers? Presses? Special circlip removers? Stuff like that? I'm pulling the 5-speed out of my 280 parts car this winter to use in my 240, and I'm going to rebuild it or have it rebuilt before using it. I'd love to do it myself, but I've never opened up a transmission (yet). I've got all the normal hand tools, power tools, etc. to do almost any "normal" mechanical work on my car. Thanks.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.