mdbrandy's Content - Page 38 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. mdbrandy posted a gallery image in Member Albums
  2. Until you start making it "bigger". Abrasive cutting wheels make quick work of removing metal :devious: .
  3. Here is the wheel well behind that portion of the rocker before work started. Hole doesn't look too bad, right?
  4. Not much. I had some indications, however. Here is a pic of the rear of the rocker before I started hacking on the quarter panel. Note that the outside of the quarter looks pretty good. The end of the rocker inside it is rusty, but reasonably intact. However, see the next two pics...
  5. mdbrandy replied to Al Squillante's topic in Help Me !!
    There's a purportedly "no rust" gas tank from a '73 on e-bay that no one has bid on yet. gas tank
  6. I glanced in my '78 280Z parts car last night, and the Heater Control Panel is NOTHING like the one in my 240Z.
  7. Well, a few weeks ago I removed 2/3 of the left Rocker for replacement, and I was vacillating about cutting out the lower rear quarter to get to the back end of the rocker. The quarter panel had been replaced 12 years ago and still seemed to be in good shape. I think it was Escanlon that suggested I might consider what things looked like under the quarter, and tonight I did. Poke, prod, cut, chisel, and in the end, it looks like this. Yikes! At least I'll be able to replace the entire rocker intact, and then the lower quarter dogleg. Thorough cleaning out, POR-15ing, and maybe I'll never have to do it again. Hopefully. Ugly stuff, that rust...
  8. Images added to a gallery album owned by mdbrandy in Member Albums
    Engine Bay from various angles and disassembly states.
  9. mdbrandy posted a gallery image in Member Albums
  10. mdbrandy posted a gallery image in Member Albums
  11. mdbrandy posted a gallery image in Member Albums
  12. There are tools to do that job. The simplest one is a "pickle fork", which is a large, two-pronged fork tool. The fork tines are thin at the front and get progressivly thicker and thus act like little levers that slide on either side of the tie rod end and push it out as you hammer on the end of the fork. Anyone else have a better description? You can get one of these tools at most auto parts stores. There are different sizes for tie rod ends and ball joints. There are also little "press" tools that I have seen that use a sort of clamp and screw arrangement to press the end out of the knuckle, but I've never used one. Good luck.
  13. Nope. Same problem even when the address is directly entered in a new window. Do you have the photos somewhere other than the guycali site, and you're linking from this site to them? That sounds like what it is complaining about.
  14. I get a "remote linking forbidden for free accounts, please upgrade your account" graphic in place of all your pictures. :disappoin .
  15. I'd say NOTHING is necessarily obvious - even with the picture, I might have not thought about it and routed it wrong. Especially since it will be a year or more before I put it back together! Tips like this can save hard-to-find parts! Thanks!
  16. The parts fiches list 5 different panels up to '73, with a break at 7/72. Then, after 10/73, it's a whole nother fiche, and the part number is different and the drawing looks pretty different. I don't think a '76 finisher will work in a '72, although I don't really know. I'd get a picture and compare - that ought to tell you.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.