Patcon

Worked on the dizzy some more I used some Ospho on the spring steel plates in the advance mechanism. It took the "blueing" off them. I might get the rest done tomorrow. We'll see. Hopefully it still works!

So I am messing around with heater boxes right now and I was pressure testing two heater valves I had. I cobbled together some hoses to attach my coolant tester to. One valve did ok, although it leaks slightly around the push rod when it's being actuated. The other leaks badly as the junction of the brass body to the steel bracketry. So in the best Captain Obvious manner, I decided to take it apart! Folded the ears back and removed the bracketry The internals just pull out after that There is a square O ring seal between the hard plastic end and an inner washer. I think if it were replaced the valve would seal up. I've started looking for suitable O rings without having to buy a 100qty. Bead blasted the valve body just for fun

I think its heat welded. It may make it difficult to maintain a crisp edge when removing the chrome trim. It is also easy to make the chrome peel

Only because you haven't assembled your at home hardening line...yet 😉

Maybe try without the tape first. Otherwise you wont know if the seal and peel actually worked

I believe the chrome strip molded to the vinyl on the panel. I don't believe it will come loose with the rivets Maybe Cantech can verify.

I have bought Milton HiFlo hose air chucks for years. I've been really disappointed in them in recent years. Them seem to start leaking pretty quickly as of late. What is everybody else using? Anyone else's experience?

@Namerow What is the best way to use those templates? I would print them but that seems like it would use a lot of ink. Is there a better way to do it?

Worked on the heater box some more today. Blasted the cases. Primed and painted. Blasted the hardware and strung it. Ready for plating. Need to test the heater core somehow

Worked on the dizzy some more. Got the advance shaft disassembled and polished the shafts. It would appear the mechanical advance is going to be 13d? Disassembled this part too I took lots of pictures! There are several little details that would be easy to miss on reassembly Might work on this part some more tomorrow, we'll see...

I plated the vacuum advance the other weekend I wired it and then put the hose on it to keep the liquid out. I plugged the advance port It turned out pretty nice for as crusty as it was. What was interesting was when it was in the tank one side would get really shiny but the other got dark. Rotate the piece and the discolorations would move. So at the very end I just wired the negative directly to the wire coming off the part and held it in the tank by hand. I rotated the part slowly and all the plate brightened up. It was really cool to watch. So this would tend to support barrel plating as giving the best finish results...

How do you do this heat and oil black thing?

@Mike

That's too funny! Well at least he's confidant in his work! That's what you want.

Here it is...

Thanks John

It's always good to find an expert!

I had a wire going through that area and used it to fish the harness in, but there are brackets and bolts welded up in that area of the car. The harnesses snag on those making it hard to get them back in

Installed the gas flap and ring today Also I was stripping down the heater box for freshening up Do anyone know if I can get this flap out? I don't see anything retaining it but it seemed like it didn't want to come out. I would also like to two floor heat flaps out too but I don't know how to de-assemble those either. I finally got the rear harness pulled in. It was a huge pain. Took maybe ten tries to get the defrost and dome light harness pulled up from the quarter panel. I would suggest not pulling those out when you strip the car if possible. Wrap them up and leave them in place...

I have been doing some plating while working on other things. These distributor clamps were plated yesterday. I plated them and then baked them for 4 hours to reduce any embrittlement. But after plating they blistered. So they will have to be redone. I suspect this is from too much brightener.

https://store.totalseal.com/collections/ring-sets Nice chart here https://www.rpmrons.com/Total Seal Rings.html#79 https://www.racetep.com/totalsealframe.html

@Diseazd Guy do you know of a place for us to shop for Total seal rings? I haven't found a source for them yet.

How many turns down are the mixture nuts? Are you sure its rich? Is the float fuel level correct?