Jump to content
Remove Ads
Welcome Guest! Please read more information about our club!

Leaderboard

Popular Content

Showing content with the highest reputation on 10/14/2018 in all areas

  1. saturday night music thread

    2 points
    The Master of Space & Time! Been to more of his concerts than probably any other single artist/band. Got to tour his home on the lake outside of Tulsa at one of the Lifer's Birthday Bashes some years ago. Hope y'all don't mind another one.

  2. 1970 240Z in SD. Surprised if this lasts one day.

    1 point
    Damn, that eBay 240z is in Wichita falls, pretty close to me! Anybody got 12k to donate to a good cause? Sent from my OP 3T using Classic Zcar Club mobile

  3. 1970 240Z in SD. Surprised if this lasts one day.

    1 point
    The CL ad looks legit. But. The phone number comes up as Skykomish Lodge in Washington state. Beware. Might be a phisherman. Or it might be a mistake. John? Good luck to anyone who tries to buy it.

  4. 1976 280Z Restoration Project

    1 point
    I got the foam from MSA http://www.thezstore.com/page/TZS/PROD/classic08f04/40-2691 less than $130 US for the foam. Bought some 77 seats so I could have the seat back adjustment that allows the seats to flip forward. I also did the leather from interior innovations with matching shift boot and ebrake boot. I figure with all of that I'm still under the cost of a pair of aftermarket race seats and still has a mostly stock look in my 240

  5. 1976 280Z Restoration Project

    1 point
    Well, a sad day today as I discovered the 370Z seats I had lined up for the 280 are not going to fit. They will, however, fit a 240Z but not a 280 with the catalytic convertor hump beside the driver. At least 3” too narrow in the seat rail area to do this without bashing or cutting out the hump. And as many of you remember, the bottom of the car is painted and clearcoated.... [emoji20] Back to plan A, restoring the stock seats. Now to find new seat foams, for less than the cost of aftermarket race seats!

  6. Lucky day for VIN 147 (HLS30-00147)

    1 point
    Aw this is brilliant. [emoji1433] Sent from my iPhone using Classic Zcar Club mobile

  7. Strut Tubes & Struts

    1 point
    I ended up getting a 2" poly carb bit that I cut down to 1.5" and used that to clean it out. Gonna finish assembly today and try to get the rears out tomorrow. thanks for the support ?❤️

  8. I’d like to do new Panasport wheels

    1 point
    My concern is true offset size. I've heard some wheels can be all over the map. I know the Panasports are 0 offset. This will be my 5th set in 30+ years of Z ownership. I'll look though. If they are the ones made in the Philippines, I can walk right up to the factory and pick them up. I have a house and condo there.

  9. I’d like to do new Panasport wheels

    1 point
    CD.....I run 16x7 Panasports with 205 55 16 rubber. No problems with clearance.

  10. Lucky day for VIN 147 (HLS30-00147)

    1 point
    Not sure on length of arm or angle but the stem is thinner. You can rotate the mirror so that the wider edge is on the top to get it higher.

  11. Let's show vintage racing pictures. I'll start.

    1 point
Remove Ads

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.