Interior
Discussions about the interior components of your early Zcar.
2,353 topics in this forum
-
- 7 replies
- 1.6k views
Hello all. I am trying to find the name of a specific piece i am missing. It is the part right under the glovebox. i can tell i'm missing something there because i see where the screws would theoretically go in should i have that completed panel. once again its the part that would go under the glovegbox but above the passenger legs (of course). Thanks
Last reply by studioti, -
-
- 6 replies
- 1.8k views
Does anyone have experience polishing/buffing black plastic such as the plastic heater control knobs, interior trim, ashtrays, etc? I have some old parts that look like they might clean up nicely, but need more than Simple Greenand a tooth brush. Thanks for your input. adamr
Last reply by ajmcforester, -
- 10 replies
- 2k views
In my 78 I was digging around under the rear deck compartment a while back and found an old breaker bar and the original tool bag up behind the seats sticking out of one of the tool box openings behind the passenger seat, but there is no cut out for a hatch in the deck or in the carpet. Ive been looking for confirmation that Datsun quit installing the boxes in later z's but I can't find any help. Is this the norm? And does anyone know where I could get a kit to install the boxes? In my old 75 280 back home it has the metal lids and everything so i was confused when there werent any on this 78.
Last reply by sparrow6190, -
- 0 replies
- 1.5k views
im looking this fenders for my 260z... anyone can help me pls? thanks:)
Last reply by kenta28, -
- 5 replies
- 1.6k views
Ok guys, before you guys start using that "search" word hear me out. I bought my 72 240 a while back and it is missing the right side door panel completely so I was searching around trying to find one and getting really discouraged when I couldn't find any new replacements (when I say new I mean manufactured in the past few years not NOS) that didn't cost as much as the car. So I got to thinking (I am an engineer after all) of ways to make new ones. I thought of fiberglass, fiberboard and various other materials. Making them in this manner would be fairly economical for making one but that doesn't help out the Z crowd... My thought is to have some thermoformed (plasti…
Last reply by Jusjofok, -
- 8 replies
- 10.3k views
In a 72 240Z can the headliner be installed without removing the windshield and side header parts? My headliner has to be replaced, but my headers are in good shape and I want to avoid destroying them to get them off the car. Thanks Miles
Last reply by zKars, -
- 4 replies
- 1.5k views
So I sat in my passenger side seat, pulled the lap belt across and now it does not retract. Anyone know how to fix this? It was working fine before. I did unbolt the contraption to hide some wires, and then I bolted it back in. Did I mess something up? Thanks, Wilson
Last reply by ajmcforester, -
- 0 replies
- 887 views
I saw a couple of old posts on this, but nothing real definitive. Does anyone know how much surgery is required to install ZX seats into a 240? Thanks.
Last reply by tlorber, -
- 17 replies
- 2.2k views
So I have been reading for an hour and trying to find a thread on someone cleaning their center console...No luck. I have a nice console but it is looking a little tired. I'm thinking the sun has faded it a little and it looks dirty even though I washed it with mild soap and water. Has anyone successfully cleaned their console, making it look good again? or is the secret to spray it with trim paint? I appreciate any feedback I can get. Cheers, Chris
Last reply by joker72z, -
I could be totally wrong on this one, but this looks to be a compe steering wheel from a sport package on a j-spec Z or it could be a 73 240 steering wheel. If anyone could help me on this one I would appreciate it. That would be so awesome if it was the compe. -Ben
Last reply by Mr Camouflage, -
- 5 replies
- 5.3k views
I got door panels that are now in quite good condition BUT passenger side panel has bended from front so its hard to install. I was thinkin that heat might have done that, cause the vinyl is ok. So is there any nice way to bend it back? re-heat vinyl or something? I'll add pictures asap. I'll also need good advices how to remake those brushes () that are in top of the door panels.
Last reply by ZCurves, -
- 8 replies
- 1.9k views
I opened my gauges but I cannot separate the lens from the bezel. I need to separete them so I can paint the bezel (mate black). Has anyone open the combinational gauges to paint the bezel and clean or polish the lenses?
Last reply by GILDIA,
-
Recently Browsing 0 members
- No registered users viewing this page.
grannyknot
