Wanted
Ads from our classified system. You can reply to want ads in this forum.
646 topics in this forum
-
- 1 follower
- 4 replies
- 2.3k views
wanted one 240z D style hubcap, one came off of my z
Last reply by lonetreesteve, -
-
- 1 follower
- 3 replies
- 1.3k views
Looking for roof for my 240Z. Mine has sunroof/moonroof.
Last reply by Patcon, -
- 1 reply
- 1.4k views
I need the following parts for 1976 280z 1. Plastic cover that hide the driver side seat mechanism 2. Hood emblems in good condition without broken post (datsun, 280z) 3. Ashtray 4. Hood release knob
Last reply by zKars, -
- 3 replies
- 1.1k views
Ontario friends & Z family, I'm on the hunt for a body shop that is familiar with 240Z's. Specifically the earlier series 1 chassis. I have a rolling shell on a frame dolly that needs to be sent out ASAP for a full body restoration. Can arrange delivery of body and all items required. Could be a good job for a reputable/respectable auto body team that is familiar with top to bottom restorations. Preferably in the GTA.
Last reply by S30Driver, -
- 1 follower
- 12 replies
- 1.9k views
Howdy, I am looking for a couple parts for my 280Z. The original owner replaced the 4 speed transmission with a 5 speed from a 1978, so I am looking to purchase the factory correct shift knob. Also, I am looking for the plug that goes in the center console, see image below. I am also looking for the factory plastic door mirror. Mine has a great mirror, but the plastic housing is cracked. Please reach out if you have any of those. Cheers! ~MattS
Last reply by borini63, -
- 1 follower
- 4 replies
- 2.1k views
I purchased and restored a 240z steering wheel for my 280z. The seller didn't have the plate for the horn. Does anyone out there have a 240z plate for a 240z horn? See picture for reference. Thanks!
Last reply by Premo34, -
- 1 follower
- 7 replies
- 2k views
I need the lid spring for the ash tray out of a 2/71 production 240Z. It's the plastic ash tray that covers the fuse panel. Thanks, --Thomas
Last reply by sensench, -
- 0 replies
- 754 views
Looking for an evap check valve for my 77 280. They are NLA and I can't get enough info to cross reference to an aftermarket one. It's the one way valve that sits near the gas tank above the half shaft. Thanks Bob
Last reply by rcb280z, -
I am piecing together an OE stereo radio for my Z I have the radio and the METAL face plate, the plastic face plate is on the way. I have a switch I hope to get locally, really only need to source the mounts that bolt to the radio. I have the U shaped mount that attaches to the console. I did not want to piece this all together but seem the only way to get a complete radio with out spending a fortune on it. here is what I am looking for. one is a simple bracket for just the radio, the other mount to the radio and provides a mount for the antenna switch.
Last reply by Dave WM, -
- 1 follower
- 11 replies
- 1.7k views
Hi everyone. Unfortunately the guy who was painting my car lost two of the flat tips for my trim molding (picture attached). I'm in need of at least two of them - does anyone have any for sale? Thanks!
Last reply by misterL, -
- 0 replies
- 1k views
I am looking for a few parts for my 1977 280. Parts needed:. Lower passenger kick panel (cut out for fuse box cover and hides wiring "highway"),. courtesy lamp assembly for overhead console (need mounting tabs intact! ...would like to find two / one for spare-future use backup), fusible link base/block assembly (#1 block/forward/towards battery) mine has broken link terminal☹️...I need a block with metal mounting tab intact and male terminals in good condition. Lastly, if anyone has a good, used aftermarket bracket set for mounting 260 bumpers to 77 280. For reasonable shipping expense, would really prefer if I could purchase items 1-3 together. Please e-mail me at dbp…
Last reply by Packerz, -
- 1 follower
- 12 replies
- 5.6k views
My current part's wires rotted away at the base and I haven't been able to find it. Would really appreciate the help. Thanks, Mark
Last reply by Dave WM,
-
Recently Browsing 0 members
- No registered users viewing this page.