All Activity

Yes, 240 with add-on air has a 3 groove pulley. Can't speak for Spirit, well yes I can but won't, but if such a car were in my now closed shop the A/C pulley would be removed.

My 12/70 car has a 3 groove pulley. I would guess the 3rd groove was added for the dealer installed A/C.

If the solenoid works fine, the likely problems are the module on the back of the ignition switch (2 screw modules may still be available from Nissan) or corrosion in the wiring.

The ZX has a 3 groove pulley. Third groove was for the power steering pump.

@Mike

Thanks, Steve....Appreciated

Yep.

Did precision plate those door latches? They look really good!

Find a weather resistant maxi fuse (or ANL fuse) holder if you are planning to mount the fuse holder where the current fusible link holders reside. I also suggest using ferrules on the wire ends to improve clamping force on the wires. You will need to find a ferrule crimper that can handle the wire sizes (relatively easy to find on Amazon). Here is an example of a marine ANL fuse holder: https://www.crutchfield.com/p_867FUSEDIS/Wet-Sounds-WWX-FUSE.html

The click you hear is normal. That is the accessory relay. Move on from that. You need to verify voltage to ground (or negative) at the starter solenoid when the key is in START. That is the black/yellow wire. Suggested actions: Pull the black/yellow wire off the starter solenoid. Put the positive voltmeter lead on the black/yellow wire and the negative lead on the battery negative. Have your assistant turn the key to the START position. Measure the voltage (and report it here). If you have around battery voltage at the black/yellow wire, then here is the next test. Keep the black/yellow wire removed. Ensure the car is in neutral. Get a screwdriver. Touch the screwdriver to the positive cable on the starter and the spade terminal where the black/yellow wire was. You don't have to hold it there for long. If it doesn't engage the solenoid immediately, try a couple of more times. Red arrow - Spade for black/yellow wire Orange arrow - Positive cable from the battery. If the solenoid immediately engages, then your starter solenoid is probably in good shape. Report your results.

When it’s time to buy a laptop, one question always comes up: new or used? The right answer depends on more than just your budget—it’s about getting the best value for your needs. In this article, we break down when a used laptop is the smarter choice and what to look for before you buy. Looking for quality and affordability? Check out Soum, a trusted platform offering a wide selection of carefully inspected used laptops to suit every need. Advantages of Buying a Used LaptopOpting for a used laptop can present buyers with numerous compelling benefits. Here are the most significant advantages: 1. Substantial Cost SavingsThe foremost benefit of purchasing a used laptop is the significant financial relief it offers. Buyers can save a considerable portion of the original cost—often 50% or more—especially when purchasing from reputable brands or high-spec models. In today's economic climate, such savings can be a game-changer. 2. Access to High-End Models at Affordable PricesGoing for a used laptop opens the door to premium specifications at a fraction of the price. Consumers can afford devices equipped with faster processors, more RAM, and superior graphics performance—all of which are typically out of reach with new models in the same price range. This makes used laptops an attractive option for various groups including students, programmers, designers, and professionals who need powerful machines without breaking the bank. 3. Environmentally Sustainable ChoiceChoosing to buy a used laptop is a responsible environmental decision. It helps reduce e-waste and extends the lifecycle of electronic products. Prolonging device use lessens the demand for raw materials and the energy required to manufacture new products, thereby shrinking the tech industry’s overall carbon footprint. 4. Conservation of Natural ResourcesBy choosing a pre-owned laptop, you contribute to minimizing the exploitation of raw materials, many of which are sourced from ecologically sensitive regions. This supports environmental preservation and encourages circular economy practices within the tech sector. 5. Greater Availability of Spare PartsOlder laptop models often come with the benefit of having more accessible and affordable replacement parts. This makes maintenance and repairs easier and more cost-effective, allowing the device to remain functional and serviceable for longer periods. Potential Challenges of Buying a Used LaptopLike any second-hand purchase, buying a used laptop comes with certain risks. Below are some of the common challenges: 1. Hidden Technical IssuesOne major concern is the potential presence of hidden defects or wear-and-tear issues. Problems may involve the battery, screen, keyboard, or even internal components like the hard drive or memory—leading to unexpected repair or replacement expenses. 2. Lack of Warranty CoverageUsed laptops frequently lack warranty protection or come with very limited coverage. This means any post-purchase repairs fall entirely on the buyer, possibly straining a carefully planned budget, especially if major issues arise shortly after purchase. 3. Absence of Cutting-Edge TechnologyUsed laptops may rely on outdated technologies that don’t support modern software or applications. This could limit your ability to use the latest tools or require future hardware upgrades, which may be costly or impractical. 4. Compatibility LimitationsCompatibility can also be an issue, particularly with newer accessories or software. Older laptops may not support modern connectivity standards like USB-C or Thunderbolt 3, reducing their adaptability and future-proofing. 5. Hidden Ownership CostsWhile the initial price may be attractive, hidden costs can accumulate over time such as purchasing updated software, hardware upgrades, or dealing with downtime due to repairs. These factors can significantly impact the long-term cost of ownership. Buying a used laptop is a smart move when done right. For trusted deals and quality you can rely on, explore Soum’s collection of inspected, budget-friendly laptops tailored to your needs.

Suggestions Please: As is, my Series I (Jan. '71 build) will start. The problem is it is taking more and more turns of the ignition key to get it to fire-up. The only constant is that every time I turn the key for ignition, I hear a very audible 'click' coming from a relay(?) mounted on the interior wall in the area of the passenger's right knee. In addition to this clicking sound, I can feel the actual internal movement by touching the metal housing with my right hand while turning on the ignition with my left hand. To help with a diagnosis, the battery is strong, and the wiring contacts to the starter motor are clean. Also, this problem occurs the same with both sets of the original ignition keys. So, is the problem coming from the keys, the key barrel, the relay (as noted above), or farther down the line to the starter? Where do I begin? Thanks

Somebody bumped the bid on the white 1970. By an odd amount. The guy buys a lot of car so there could be an interesting battle on tomorrow. Does anyone know if a 1970 240Z could have a three groove damper pulley? It has an L28 crankshaft so the damper has been off. The sellers on BaT are interesting because they often don't really know the details but don't want to say "I don't know".

I don't know what others are using but I installed a pair of marine brakers on the firewall.

They have this kit and one with several more pieces, which I assumed was for 280zs.

Good luck, and just let us know if there are still unanswered questions.

@Matthew Abate Do you know if Newark Auto makes a carpet kit for the early cars? You're making good progress!

This is all great info regarding date codes. I had to check my parts on this as the drivers door on 00042 was obviously replaced, passenger door is original. Drivers door has a 5-5 date code, while passenger door is 9-8. Amazingly, I checked my stash and I actually have a 9-8 driver's latch. Guess I will swap those out so they both say 9-8 Last pic shows the two spring types

That was the 1st pic I posted, here it is again. The clock spring was only on one of the batch of six I picked up, all the others used a coil spring. What was interesting was that five of the six bodies had the straight slot, not the "T" slot. Pretty sure the "T" slot was an improvement to retain the bumper - at the bottom of the pic. Sorry I don't have a better pic to discern the date codes. I recall one set was matched and an early date, I think they went to @26th-Z .

So the early locks had the T-slot? Do you have pictures of the spring side of those locks?

So cool! Fun build and I love following along. Gosh I hate facebook compared to forums.

never know when a September/October 69 dated glass may pop up!!??

Got it, thank you! Now to see if I can figure out what it is saying. lol

Perfect. I just couldn't see the bottom washers in the other pics. Looks great.

The lock core has its own date code. Below on the left is year 0 (1970), month 3. On the right is year 9 (1969), month 7. The lock assembly also has its date code. This one is Left, year 0 (1970), month 4, day 16 (I think). This pic is the assembly for the 0-3 lock core above. Just for grins, here is the lock assembly for the 9-7 core above, note the difference in the slot as you noted on one of yours.