Everything posted by mdbrandy
-
Care in Removing Gas Tank Parts
I hadn't looked at the back side. I'll do that ASAP when I get home. Tried that. Not loose enough to do it yet. Hmm. I guess I should know the difference, but I don't. I'll stop by the hardware store on my way home and ask for "penetrating oil". Any specific brand(s) that work best? Thanks a bunch - Any new techniques to get some of these old rusted fasteners loose will be useful forever!
-
Care in Removing Gas Tank Parts
I'll just be as careful as I can, and hopefully, the strap will survive... The padding can be replaced with a plain piece of rubber. Buy that at the local hardware store and cut it to fit. I'd thought about that, but since I didn't have them off yet, I wasn't real sure what the padding was. Sounds easy enough. Thanks.
-
Care in Removing Gas Tank Parts
I'm slowly going through disconnecting stuff getting ready to remove the gas tank. As expected, most of the screw clamps, bracket screws, and bolts are pretty corroded, but I've removed most everything so far and I'm starting on the strap bolts. The upper one came loose without too much trouble, but I'm having a time with the lower (left) one. If the darned strap didn't try to twist, it'd be a lot easier. Even with a 14mm flare wrench on the nut above the bracket, it is very hard to keep the bracket/strap from twisting with a socket on the lower nut. I've now been soaking it overnight in WD40 to see if that helps when I try again tonight. So, my main question here is how careful should I be with these straps? The tank looks OK so far, but the straps are pretty rusty, and the "padding" or whatever it is called between the straps and the tank is in really tough shape. I don't see new straps or cushioning in any of the catalogs (MSA, VB) that I have, so if I managed to damage the strap that I'm having trouble with, is that going to cause me huge headaches to get replaced? It would be nice just to cut the darned strap if they were available :devious: . Thanks.
-
Are early gas tank vent systems simpler?
Thanks Chris - good to know that the system hasn't been hacked. By large and small boots, do you mean the one that comes through the rear floor (big), and the one that goes down through the wheelwell (small)? I ask only because the wheelwell hose HAS NO BOOT AT ALL! I intend to replace essentially every piece of rubber on this car that I can obtain, so thanks for the source:classic: . I've been on Banzai's site, but hadn't looked for these specifically yet. And I LOVE my digital camera. I currently have 373 pics of the car and it's systems as I've taken it apart. It'll be a lifesaver when I put it back together, I'm sure! I also use it for kids baseball games, concerts, birthdays, etc. I used the zoom to take a nice picture of a big blue heron on our pond the other day. I bought a nice one (Nikon coolpix 4500), but it gives me full manual control when I want it, which many of the less expensive cameras do not. Bambi - zparts has a small page about vapor leaks, and seems to be into vent parts. Might ask there for the t-tube. http://zparts.com/zptech/articles/gasfumes/gasfumetech1.html Thanks all.
-
Are early gas tank vent systems simpler?
I'm looking at my gas tank vent system now (I'm planning on draining and pulling the tank tomorrow), and finding that it looks much simpler than what the fiche shows. Essentially, there's the main filler tube, a vent that comes off the tank and back to the filler tube, and one other vent line that "T's" off the tank vent line, goes up in a loop and back down through the wheel well and just opens there under the car. (Picture attached). The fiche indicate that the "tank-reservoir" 17350-E4600 goes from "no date" to 6/71, which makes me think that I'm missing something . Has someone ripped out much of this system , or are the very early (11/69) systems just that much simpler :classic: . Thanks.
-
Advice on lifting engine?
Well, thanks for the opinions, gents. The engine is out. I used the upper right Bellhousing to block bolt hole with a new grade 8 bolt (that I had purchased to use on the engine stand anyway), and the front lifting ring. As I didn't fully trust that ring, I also wrapped a length of 1/2 inch nylon rope that I had laying around under the engine and through the crane hook as a kind of safety at the front of the engine. It's a strong rope - I don't know it's capacity, but it is hundreds of pounds. Pushed the car back out of the way, lowered the engine onto a pallet, lifted the engine back up to put on the stand, and all is well. Only problem I had was the back of the tranny catching on the rear mount crossmember for a minute. Onward with the restoration! :classic:
-
Advice on lifting engine?
Rented Engine hoist and a three car garage with 12 foot ceilings. Much nicer than when I did it in my parent's one car garage 20 years ago. Does sound easier to move the car instead of the hoist. I'll try that. if the engine starts to swing, its time you stick your head between your knees and kiss your arse goodbye. I'll remember that :hurt: . I personally can't see all the fuss about taking the head etc off to reduce weight, ... I'd just rather suspend 500 lb then 800 lb (or whatever it is). Less stress on a rented hoist/chain that SHOULD be in good shape, but you never know... ...as long as you take it slowly and tag everything you remove you will be fine. Slow is the ticket. And I have several boxes of ziploc bags full of small parts, labeled and stored, along with several hundred digital pics of everything before during and after I disassembled each thing. If I can't figure out how to put something back together with all this, it will just have to stay apart! "Never stick your finger in a hole you wouldn't stick your d*** into" I'll keep that in mind too :classic: . Lets say that there's lots of places fingers can fit that other things can't....
-
Advice on lifting engine?
Wow, some interesting anecdotes here. I'm going to use the bellhousing bolt in back - at least that goes into the block, and the bolt is in really good shape - still has the yellow zinc plating. I'll look into what I want to do in front. I'll at the very least remove the front mounting eye and inspect the bolt very closely. Maybe I can use one of the alternator bolts on the block just below the front lifting eye. Nice big bolts there! Thanks for all the results of your experience - that's what makes this forum so valuble!
-
Advice on lifting engine?
I do have the book, and I've read about the first half of it so far. It has an amazing amount of good information. However, it doesn't have every detail about every thing you might want to know. All it says about the engine lifting points is to use the two lifting rings. Since I still want to minimize the amount of slung weight, he didn't answer my specific question, which is why I asked it here. I knew someone would have had some similar experience that I could learn from :classic: . I spent 15 years doing risk and safety engineering work, so I try to minimize my risks wherever I can (like by lifting the least amount of weight, and understanding what can fail). I'll undoubtedly increase my risk when I get the car back on the road and up to speed around some tight corners :devious: Thanks.
-
Advice on lifting engine?
You still used a hole in the head? The front lifting ring is just above where you said you attached your front chain. Makes me wonder if attaching to the steel block would be better than the alumunum head, but that'd probably make the attachment points too low, and make the assembly unstable to lift. I'd think that the grade of bolt for this wouldn't be that important, since it seems to me that the aluminum threads in the head would give long before even a grade 5 steel bolt. Why did you decide not to use the lifting ring right above where you attached your front chain? Thanks for the discussion!
-
Advice on lifting engine?
I guess I need to ask what you mean by 'popped off'? Do you mean that the stud that it was attached to stripped and the stud and lifting ring came out while you were lifing it? That seems kind of ugly! I like your idea of attaching it to the bellhousing bolt. The rear lifting ring on mine is nothing more than a flat piece of steel with a hole for the bolt and the ring for attaching the chain/hook. The left top bellhousing bolt is only a couple inches from the rear exhaust header stud, so it won't change the geometry much, and is probably a lot stronger. Barring other good suggestions, I'll try that. Anyone else have problems with the lifting ring(s) "popping off"? Thanks.
-
Advice on lifting engine?
OK, I'm about to the point of lifting the engine out of my car. Got the hood and entire front body off (grill, headlight buckets, etc.). I decided to "lighten" the engine as much as I could before lifting it by removing anything I could. Figured I'd lift as little weight as possible. So, when I took off the intake manifold and header, I discovered that the rear engine lifting ring is attached to the rear header stud. So, I have to put that stud and the ring back on. I intend to put a stack of washers between the head and the lifting ring of the same thickness as the header flange. Questions: Anybody done it this way? I hadn't considered earlier, but now wonder if the balance of the engine assembly might be adversely changed and make it more difficult to get it out. Any thoughts? Anything that I REALLY shouldn't take off before lifting it? I'm leaving the transmission attached, but taking off the starter, alternator, manifolds, distributor, etc. Leaving the head and valve cover. Thanks for any discussion.
-
Size of rubber fuel line on 240Z?
Which fuel hose - stuff in the engine bay, or vent lines and hoses from the tank in the back? If it's any of the stuff in the back, a good article can be found at: http://www.physics.ohio-state.edu/~jrdemers/280ZX/tankvents/tankvents.html I haven't replaced the engine bay lines yet, so I don't know those.
- Sex or Z?
-
280Z 5 speed in early 240Z
Good. It's a manual now, although I'm not sure what it is. I know it isn't the original transmission, and the PO said it was a "truck transmission", whatever he meant by that. I'm not sure he really knew. If nothing else, I have an extra driveshaft out of a '71 240Z that would work then. Thanks for the info.
-
Where's the vents???
And of course, you're right. Chalk it up to learning too many things in a short time, and writing this from work, when the car's at home. I actually had a picture on my computer here, and yup, the slots are filled in on mine. I have an extra wheel off a '71, and I guess I got them mixed up. Page 4 off the original 1970 sales brochure also shows the filled in spokes. (http://www.zhome.com/zcarfilesJPEG/70Broch.htm) Thanks for straightening me out! :stupid: On another note, I found this on zhome.com about the valve cover: The early Z's had valve covers that said "NISSAN 2400" - they changed when the A/T Transmission cars came out, somewhere around 10/70 (HLS30 12658). From that point on most of them said "NISSAN OHV" - although there seems to be an overlap period of some months that cars were equipped with either style.
-
Where's the vents???
Oh, and it has the latch on the gas tank door, which is indicative of early cars, but I don't remember when it changed.
-
Where's the vents???
Uhh, I'm pretty sure that the original '70 Z's HAD the cutouts in the spokes, and that they started being filled in in '71. My 11/69 HAS the cutouts. The transition from the 2400 valve cover to OHC occurred in late '70 I think as well. My guess is that if it is a '70 model, it is very late, and is a transition car that has parts from both years. Either that, or it is an early '71 that has a few features of the '70. OR, it was in an accident, and the hatch and rear quarters were replaced. Doesn't explain the valve cover, though. Could be a lot of things...
-
Driving Music...
When I used to drive between Los Angeles and Central Illinois a couple times a year in my 280Z, one of my favorite tapes (no CDs in 1985) was REO Speedwagon's Double Live album "You Get What You Play For".
-
280Z 5 speed in early 240Z
That's good to know, but the issue seems to be (given my limited knowledge so far) only with really early series I 240Z's. I gather they moved the differential back a little sometime during the beginning of the series 2 cars so anything in 1971 or 72 will be different from my 11/69 production car. However, what I don't know, is maybe the drive shaft and differential are positioned in each of them such that the 5 speeds will work in either version (i.e., I'm thinking that maybe the drive shafts are different lengths and they end up at the same position at the end of the transmission. Don't know. ) Anyway, thanks for the input.
-
280Z 5 speed in early 240Z
Thanks for the link - I've read that one, as well as some info on Zhome.com. What I'm mostly worried about is what problems I might run into due to the fact that my car is about as early as you can get, and much of the information available alludes to potential problems with really early cars and the swap, but I haven't heard from anyone that has actually done it. I think I'd like to just swap the tranny and not the shaft/differential, and most of the info is for swapping the whole driveline. Anyway, I'm still reading and searching, and a long way from actually doing it. :cross-eye :classic:
-
The statement car owners make:
Hey now, the only closet I'm still in is the one holding all the Z books and catalogs! Some of us family dudes need cars that hold more than 2 to go along with our Z addictions :classic: . And that supposedly are "reliable". At least I got the 192HP V6 and the 5 speed in my Camry... too bad about the nasty torque-steer when powering through a corner, though.
-
How does this come out?
Yup, it's #215. I'm looking forward to restoring it as much as I can. It has some pretty serious floor/frame rust issues, but most of that can be fixed with Charlie Osborne's stuff. It's amazing how simple these early cars are. I've probably only spent 20 hours stripping it so far, and in another 20 it'll be nothing but the rolling shell. And that includes taking hundreds of pictures, bagging every bolt and grommet as I take it off, etc.
-
How does this come out?
In case you're interested, the interior of the car is pretty much stripped right now, and looks like the attached photo.
-
How does this come out?
The attached picture is of the grommet on the passenger footwell kickpanel where the cowl drain hose goes through. The drain hose has been removed. It was just loosely glued in place. I'd like to remove this grommet, since as you can see, there is a bit 'O rust on the firewall right beside it that will need to be fixed, and I suspect welding that close wouldn't do it any good. I've poked, prodded, pulled, etc. at it, and it isn't apparent to me how it is attached. It doesn't feel like how the firewall grommets just have a groove that the sheet metal fits in. I've felt around inside the opening, and I actually can't feel a definate edge on the inside, so I'm a little baffled. Any ideas? If I removed the fender, can I see this grommet from the other side? Thanks.