mdbrandy's Content - Page 24 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. I'm not much of an engine builder (yet), but I am under the impression that fly cutting the pistons is done for valve clearance, so you don't have the valves impacting the pistons if you have inadequate clearance. Decreasing compression ratio is a side effect of this. FWIW.
  2. I think this is about the 10th one of these I have seen put up there by these guys. They always sell, but rarely for the buy-it-now price.
  3. The thermotime/cold start combo is what I'm planning on checking when I get the time. The air regulator really shouldn't cause this problem - it just raises the idle speed by supplying more air if I understand right. I am having a bit of trouble understanding what the fuel pressure would have to do with it.
  4. Fuel regulator? So the flow is too low when hot, too high, or what? That's one I wouldn't have thought about. I haven't had time to look into it yet, but several days this week, it has started fine when hot, but today it ran like a tank when started hot again. What lead you to look at the fuel regulator? Thanks for the tip!
  5. I don't have many pics of that area before I took the bumper off, but here's a pic from my 11/69 car that should do you. See the circled area at the very top.
  6. mdbrandy replied to CableSrv's topic in Help Me !!
    Do you live on the board Carl ?!? I thought I was fast enough to get mine in!
  7. mdbrandy replied to CableSrv's topic in Help Me !!
    It's my understanding the the horsepower and torque curves peak well before 7000 rpm on a stock engine too, so there isn't much point in going higher.
  8. Woah. There's a diss for the 350Z. At least the guy liked the 240Z :classic: .
  9. Yup. I got some a couple months ago from her. They'll be really nice when it's time to put things back together. Now if there were just new straps to be had....
  10. Is there really a module on the distributor on a '75? On my '78, the actual ignition module is on the passenger kickpanel in the footwell. I thought that the ignition module didn't actually get attached to the distributor until the 280ZX, with that E12-80 module that is so coveted. Another thought is the magnetic pickup inside the distributor. I was having trouble getting a '78 280Z parts car started (before I decided it was a parts car), and found that the pickup itself inside the distributor was bad. If memory serves, the wires were frayed and corroded as they left the pickup body, which was not obvious until I removed it to look at it. Good luck...
  11. mdbrandy replied to CableSrv's topic in Help Me !!
    The Haynes manual is British. Overseas, some 240Z's had 5 speeds, but in the US, I believe all we got were 4 speeds up until the 280Z, and the 5 speed was a option for it. Assuming you have one of the later 280Z type of 5 speeds, replacing the bushings on the shifter is very easy. Three plastic pieces and less than $15. You can get them from one of our sponsors - www.midwestz.com.
  12. Hadn't thought about screw jacks - I've seen them but don't have any. Sounds convenient. I've got six 6 ton jack stands right now. You're right that there's not much weight left, but the front end still needs to be supported so it wouldn't sag, and it sounds like you are. Thanks. I might look for some screw jacks. :classic:
  13. With all that front frame cut away, how are you supporting the chassis so that when you weld new metal in it will be straight? Just wondering, since I have some similar work to do....
  14. Ed, how would you go about adjusting the T/C rod position? Only way I could see would be to shim at the rod pocket, although I'm not quite clear how to do that either. Stack of washers on the rod before you slide on the bushing cups or something? Edit: Although in this case, the rod would have to go the other way. Wouldn't you have to remove the inner busing or something to move it backwards without bending the T/C pocket? Confused...
  15. The position of the center of the tire is located in space by three things: The strut, the control arm, and the T/C rod. I can't see how the tire could be forward of where it should be without the T/C rod attachment on the frame being bent forward or something like that. The T/C rod is the cylindrical steel rod that runs from the outside end of the control arm back to a "pocket" on the frame in front of the firewall. Of course, the frame itself could be bent too. Not sure of what else could cause that kind of geometry change...
  16. mdbrandy replied to CableSrv's topic in Help Me !!
    Also, you only need 5 qt oil for the engine, including the filter, and unless the transmission has been changed out (very possible with these cars), it is most likely a 4 speed.
  17. mdbrandy replied to gema's topic in Open Chit Chat
    Tomohawk has a whole list of ZZ Top near the bottom of page 2.
  18. Now THAT sounds promising. I had forgotten that I had downloaded that FI manual that 2manyZ's referenced. Just looked at it, and the thermotime would certainly seem to cause exactly this problem. I'll try to test it tomorrow. It's been idling high too, so I guess it's time to read that manual more thoroughly. The air regulator appears to be a possible problem for that... Thanks!
  19. Interestingly, I have exactly the same problem. Mine's a '78. Wasn't a problem while the temperature never got above 25 or 30 degrees F, but now that temps are getting up to 50+, it has become a problem. After the car is fully up to temp, if I stop it and let it sit for 5 or ten minutes, it starts hard and runs like a tank. If I give it a bit of gas pedal for a minute or two after starting, it smooths out and runs fine. It starts cold fine, and runs fine after that initial hot stumbling start. I'm not sure if this is a symptom of another problem - I know I need to replace my fan clutch. While driving, temp is fine, but if I idle for 10 minutes or something like that, the temp starts climbing. Fan doesn't lock at high temp, so I know that's a problem. So, I have been thinking about it, and wondering if it is vapor lock from heat soaking after I stop, or maybe the temperature sensors at the front of the engine are getting hotter than they should (namely, the FI temp sensor and not the guage one) after shutdown since there wasn't sufficient fan cooling. That one seems a little off the wall, I guess. I have wondered about a couple of 280ZX engines I looked at while I was looking for my Z in September. They had some kind of a fan/blower that seemed to take air from the sparkplug side of the engine and blow it on the injectors. Seems to me that would indicate a heat soak type of problem. Does anyone know if this is a known problem?
  20. Bambikiller is right - here's a pic of my 11/69 car as I was stripping it down.
  21. Bhp

    mdbrandy replied to zeiss150's topic in Engine & Drivetrain
    As long as you have the drivetrain and tires to get it to the road!
  22. Bhp

    mdbrandy replied to zeiss150's topic in Engine & Drivetrain
    Several of the other google'd web sites I was looking at defined BHP as being measured with a friction brake - thus a known force applied to the brake with a known coefficient of friction should be able to measure the energy it takes to stall the engine. Don't know the details of it though.
  23. Bhp

    mdbrandy replied to zeiss150's topic in Engine & Drivetrain
    After a little googling, I found the following at http://www.corridor-o.com/html/kids/html/horses.html:
  24. Bhp

    mdbrandy replied to zeiss150's topic in Engine & Drivetrain
    Horsepower and KW are both just units of power, and mean the same thing. Power is a measure of energy per unit time - a kilowatt is 1000 Joules per second. A joule is a measure of energy. I'm not sure what the english units are that go into making up a horsepower, but it's the same idea, some unit of energy per some unit of time. I think the main question for an engine is, where is that energy per unit time available - there are losses through the transmission and differential, so that there is less energy available at the rear wheels than there is at the flywheel.
  25. I don't know the lengths, but all of those hoses are high-pressure fuel line, and you can't just use normal fuel line. Maybe return to the tank is lower pressure, but all the supply and injector lines are high pressure. Somewhat more expensive...

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.