siteunseen

Just turn the nut on the bottom a half a turn either way and drive. It's been a few years but I'm thinking counter clockwise brings the high rpms down. Google it, "BCDD adjust 280z"

There's an N42 on the classifieds now. I put a block off plate on my n47. There's a tunnel under there I don't think you can shave away. People talk about shaving, they're talking about the bosses all the crap bolts into. If you have access to a drill press and taps you can make your own rail for less than $50. It isn't easy though so Palnet is the easiest if you have the money.

Should she unhook the battery as well as OFF position? I've read that before but have know idea.

I've seen quite a few RHD in the U.S. Apparently legal.

So the highest octane has a higher boiling/vaporization temp? And has the least amount of oil, right?

If he still has it, @rossiz, has a complete efi system to sale. He went to carbs on his '78. Non egr intake, new injectors, all the good stuff.

Are you checking hemmings.com? The nice ones show up on there. There's a nice Z 432 now. $189,500.

Ooops! Sorry about that, thanks for correcting my mistake.

It's not in color but the colors are noted. http://www.atlanticz.ca/zclub/techtips/wiringdiagrams/78_280Z_wiring.pdf

This was very helpful for me and my '77, it sat for many years before I bought it. It seems to me that when the EFI gets out of whack people just park them. Thank goodness for the internet. http://atlanticz.ca/zclub/techtips/

Looking at your picture I think the timing is off, retarded. The vacuum advance dashpot should be close to 8 o'clock. If you set the high idle screw like Lumens suggest, turn the distributor clockwise to advance it.

I'll pile on here too, rocker stripes are wrong and the right ones are available. ( ○ )

Click on your username and look in the address bar. I'm on my phone now but I believe your's is 30276.

The fitment guide is pretty extensive.

What do the new plugs look like now, first three compared to the last three? A new rotor button and cap are cheap and will get that out of the way. The only large hose I can think of on the balance tube is the brake booster hose towards the rear and then the PCV fitting and hose in the middle. Good luck, hopefully it's something small.

I changed mine out on a '72, it was a "hard' pedal and the PRMs would rise when I depressed the brake pedal. Surprisingly tough for me and I'm glad I decided not to go with the bigger booster from the 280s, drilling new mounting holes through the firewall. I loosened the MC from the booster and tied it in place with some wire coming down from my ceiling, pulled the old on out and finagled the new one into place. Then the PITA part was getting those 4 nuts on the threads above the pedals. It was tough, for me anyway. $100 for a remanufactured one that I needed to paint black, it was raw metal when I received it. If you can get a new booster, the lines flushed of air with new fluid for $250 that's not too expensive after doing the job myself. I would gladly pay that if I need another one.

Use your core muscles for bending, Sensei.

I agree with Zed Head. That line inside the sprockets groove or anywhere close is a definite verify for TDC. It would save you from unneeded work. If you know you're going to rebuild the motor sooner or later go ahead and get the timing kit and use the sprocket for now. It looks to me your not far off. The motors are so easy to build and set up that whoever rebuilt it last most likely got it right and we are just missing something simple. I'll try to find my OE sprocket tomorrow and measure the grooves location, then hopefully you can get close lining up the line in the grooves location.

Or the local plumber's supply? That's where I find mine.

I was sweating profusely after walking, being pulled around by, my dog. Just joking around.

The cam should have JAPAN and E30 in raised lettering in between #8 and #9 lobes, I went downstairs and looked up close. I think those rough edges help keep the oil on the lobes???

Here's the original E88 head on my 2/'72 when I first bought it, I was having the same problems you are. The original sprockets have 4 oblong holes. And my cams have a rough edge too, they'll scratch your fingernail. Original cams are stamped "JAPAN" where the red circle is, mine's kinda dirty and hard to make out from the picture. Here is my thread on everything lining up for the timing, and some comments on moving the chain to fudge the timing.

Here's some direction for installing a clear filter out of the fuel tank. It will let you see if there is gunk in your tank and keep it from getting further up the fuel system. http://atlanticz.ca/zclub/techtips/fuel/g3filter/index.htm

Holy 5hit, 15 feet! Could you post up some pics of snow angels in the Boobies thread?