Zed Head

Check inside the fan housing. Mine was full. The top of the glovebox was the toilet area, apparently.

There's a P90A head for sale on Hybridz for $200. North Carolina "P90a head complete with cam and all rockers. $200 "

You have a completely different animal than a 1983 280ZX turbo engine management system. Better be careful, these engines blow head gaskets or break rings easily when turbo'ed. The Z31 ECU uses a CAS also. Open a 1984-87 FSM EFEC chapter to see the details. Your Crane ignition box might be wired for universal trigger, but that's probably not what's under the distributor cap. The ECU triggers the ignition. You have more than a little bit of time and effort in front of you. Should be fun though.

1983 turbo systems use a CAS to the ECU and the ECU controls the coil. The universal magnetic trigger implies that you don't have the 1983 turbo system. What's controlling the EFI on your engine?

Interesting that you got Standard. Eiji didn't bore a size over? Might check bore size with your guy. Break-in depends more on the rings I think. But most products come with instructions. Follow those.

I used a piece of string to figure out how long the parts store line should be, and wood screws on a board to bend it. Lay the old line on the board, put some screws inside the bends, bend the new line to match, repeat for each bend. The advantage of the board and screws is that if you place them right you won't over-bend, plus you can go slow and see when you're close. Beware though, average line will work harden so it's only (easily) bendable once.

We need that part number though for the AC Delco kit. The pictures on the interweb don't show that it comes with the washers, sleeves, and nuts. Much better than the Moog set, which is just the rubber. Just post the correct orientation and it's a nice little informative story.

Weird that eBay won't let you search for a seller, only an item. Tried to find pioneer556 but got nothing. Did find a P90 head from him though. That's a lot of money for a bad head. Probably get a whole car with the head for that money, somewhere. http://www.ebay.com/itm/Nissan-280ZX-Turbo-Cylinder-head-P90A-1981-83-rebuilt-/331837762669?hash=item4d43126c6d:g:XZcAAOSw2ENW64YW&vxp=mtr

Thanks for completing the circle. These engines are very susceptible to detonation damage and to detonation. Even the best parts can't withstand detonation.

http://atlanticz.ca/zclub/techtips/suspension/comprod/ball&socket/index.htm

The distance piece is supposed to match the bearing race in the hub. Its purpose is to match the inner race distance with the outer race distance, of the ball bearing assemblies. Described in the RA chapter, I think. Letters are stamped on the piece and the hub and should match. There's also a table showing specifications. Attached the 1982 chart.

There's a factory washer that's thicker and more rigid than average, and designed to fit against the step on the rod. And another to go on the other side of the sandwich. What you took apart is an aftermarket kit, designed to make the front control arms more stable. The factory rubber is pretty floppy. You might be able to get replacements for the spherical pieces and kep using what you have. If you go with the ES urethane you'll want to only use the front and use factory rubber on the back. The rod ends tend to break off otherwise, from flex fatigue.

Much better but is that for 1972? My snippet was from what's supposed to be the 1972 BE chapter. The fuse panels are different so that should give a clue.

Maybe Horn Relay is the horn button mechanism. The switch shown is a manual switch, releasing power from the fuse panel to the horn and back to the combo switch through the coil shown. Can't find a Horn Button on the diagram. Your best bet is to just check for power at H on the fuse panel, then probe the parts at the horn button area for power. SteveJ probably knows. A title change might catch his eye. Others might know also. My horn has always worked and I have a 76.

There does appear to a fuse for the horn at the fuse panel. Worth checking first. Have to say though, that I can't understand the horn relay wiring diagram provided by Nissan. They show the solenoid, the switch and the horn all connected to the same spot in the relay. And the relay sends power back to the combo switch. Since the horn is grounded at its mount that would have the horn on all the time. Odd. Unless it's set up to work like a transistor. GB provides power to actuate the horn through the switch and the fuse. Using the same ground circuit, the horn itself.

Detonation breaks the ring lands, and the edges of the pistons. Powerful explosions on the tops of the pistons. Once you get a fracture it can propagate. I have a vision of somebody not realizing what that engine noise was and just driving and driving with timing mis-set or low octane fuel. Basically beating the heck out of the piston tops. I filled my 1969 GTO with low octane and it was torture putting around at part-throttle waiting for the needle to get close to E. Should have siphoned it out. I had the intelligence of a high-school kid though. Could be that over-heating was involved. That might warp the head and blow the head gasket, which would explain the new head. It might have had damaged pistons when the new head was installed.

You can make your horn beep with a piece of wire, or a screwdriver, from its state of disassembly in your picture, if it's connected properly and they work (they're behind the grill). The power is there, and the horn button and its metal parts just provide the ground. This is not the problem you started with, but good that you redefined it. Could be that the horns themselves are disconnected.

Somebody on Hybridz had a turn signal problem and it turned out to be a bad bulb. I got distracted with the meter readings showing power and no power, but still not clear what's being measured. There is also one other huge problem. 10.27 volts is a dirt-dead battery. Edit - I heard the "bloop" while writing and there's SteveJ. On the 10.27 volts - the flasher needs current. 10.27 might not be enough voltage to drive it. Could be just a simple battery charge will do.

That was my point. There's no green wire involved in the turn signal system, according to the diagram. Why put your probe on green if it's not involved? Green-red, green-black, and white are the wires on the harness side. I don't know what color they are on the signal side. But for wiring diagram discussions, it would be best to use the colors shown in the diagram. Without their own 1978 signal nobody knows what green is supposed to do. I have a 78 signal, but it's in a box in the garage.

The ID numbers are but the parts themselves may not be to spec. The head was probably skimmed, raising the compression ratio, for example. You have a custom engine now, F54, P79, etc. are irrelevant.

Already miss knowing that he's there to set bad advice right, confirm good advice, or to just add something significant to a topic, from his years of experience. He was active on all three of the forums I roam around and his posts were always worth reading.

There's your problem, maybe. Better have that head checked. Check combustion chamber volume. Calculate compression ratio. ID the cam profiles. Surprising that the PO would change the head at 5,383 miles. He was either trying to hop it up, or he damaged something. Looks like you have some good parts but you should probably make sure that all of them will work well together.

Uh-oh. I should have stuck with my instinct. Hope she didn't buy that 77 button. Are you saying it didn't fit? Or that it did but looked horrible? If the three stand-offs that fit in the holes are on the wheel, which they seem to be in her case, it should still slip on if there's room.

You mention green but the two outlet wires are Green/Red and Green/Black. I would go to the FSM before the forums. Note the flasher. It works by getting hot from current flow, opening the circuit, then cooling and closing the circuit. Click, click, click. Might be a possibility. Also note that of the 6 only 3 are turn signal.

I think that it would be fair and appropriate to contact Datsun Spirit and see what they say. Post #13 says that he built the short block. Finding rings in the pan means that the piston must have broken all the way up to the ring lands. That's a big deal. #5 and 6 are the detonation cylinders though. A perfect engine with a bad tune will still detonate and break things. One tank of low octane a hot day and some hills could do it also. But at least confirm that you didn't get scammed with paperwork for a different short block. Could be that Datsun Spirit did not actually build that engine. Just trying to be fair overall. If this was a California Datsun engine we'd be tearing in to Al right now.