Jump to content
We Need Your Help! ×

IGNORED

Starting Carb Conversion: Flat Tops to Paltechs


Dadsun

Recommended Posts

On 1/24/2021 at 7:35 PM, Racer X said:

I forgot to mention, check the header and manifold mating surfaces for flatness. Using a straightedge with a ground flat edge check that all surfaces are flat, and square. Anything more than .002” or .003” off will be difficult to get sealed and kept tight.

Well, Racer mentioned it and now that it's off the car, the header does have some significant issues on the flatness from one end to the other. In particular the front most exhaust flange is pretty much worn away. I could have my friend braze another lip around it and then try to grind appropriately, but I don't think I'll get it within tolerance that way. Or could have a competent machinist, but that'd probably be a lot more hassle and maybe even higher cost than just buying a new header. Ugh. Wish I would have known what to check before paying to have it ceramic coated. 

I think one of you highly recommended a 6-to-1 header upgrade?

Btw, someone said it looks like the header has been leaking for a while. No, that's just how much carbon has built up in the engine. I've had the header back on a month and probably have <1 hour of run time, almost all of it in my garage while I was tuning the carbs.

PXL_20210208_224307949.jpg

PXL_20210208_224250973.jpg

  • Like 1
Link to comment
Share on other sites


2 hours ago, Dadsun said:

Well, Racer mentioned it and now that it's off the car, the header does have some significant issues on the flatness from one end to the other. In particular the front most exhaust flange is pretty much worn away. I could have my friend braze another lip around it and then try to grind appropriately, but I don't think I'll get it within tolerance that way. Or could have a competent machinist, but that'd probably be a lot more hassle and maybe even higher cost than just buying a new header. Ugh. Wish I would have known what to check before paying to have it ceramic coated. 

I think one of you highly recommended a 6-to-1 header upgrade?

Btw, someone said it looks like the header has been leaking for a while. No, that's just how much carbon has built up in the engine. I've had the header back on a month and probably have <1 hour of run time, almost all of it in my garage while I was tuning the carbs.

PXL_20210208_224307949.jpg

PXL_20210208_224250973.jpg

Interesting how the one flange looks flush where the tubing comes through, rather than protruding and then ground to make a flat ridge around the port (which aids sealing).

Sure, you could pay a competent machinist to repair it, and spend more money, but is it really worth it? I see it has emissions bungs, that are not being used. Getting a header that doesn't have them makes more sense if you aren't using the AIR system. Having tubular exhaust is all about maximizing air flow through the engine, and the flow past the unused bungs will be disrupted some.

As for what header, consider the engine as a whole, and choose accordingly. 

Personally I am considering a full stainless steel system from that guy in France. His systems look nicely done, and can be tailored to the engine build and intended use.

I just need to save the cash.

Link to comment
Share on other sites

@siteunseen, are these the parts you bought? (FYI, I have the original 240z S30 2.4 liter engine)

Header:

https://www.thezstore.com/page/TZS/PROD/classic19d/15-6012CH

Exhaust:

https://www.thezstore.com/page/TZS/PROD/classic19d/15-6309

Gasket: this is the exact gasket I just bought last month... I may just leave it on and salvage it. https://zcardepot.com/products/manifold-gasket-intake-exhaust-oem-240z-260z-70-74?_pos=3&_sid=ee7b757b0&_ss=r

 

Edited by Dadsun
  • Like 2
Link to comment
Share on other sites

Yes sir, yes it is, and I love it. Has a high rpm raspy sound on my 2.4 and a totally different sound on the 2.8. I had a 20" resonator installed on the 2.8. It had a horrible drone on the interstate but the 240 is perfect. Music to my ears. It reminds me of the motorcycles I used to ride. I'd describe it as screaming bloody murder to slow down. LOL

 

Link to comment
Share on other sites

1 hour ago, Dadsun said:

@siteunseen, are these the parts you bought? (FYI, I have the original 240z S30 2.4 liter engine)

Header:

https://www.thezstore.com/page/TZS/PROD/classic19d/15-6012CH

Exhaust:

https://www.thezstore.com/page/TZS/PROD/classic19d/15-6309

Gasket: this is the exact gasket I just bought last month... I may just leave it on and salvage it. https://zcardepot.com/products/manifold-gasket-intake-exhaust-oem-240z-260z-70-74?_pos=3&_sid=ee7b757b0&_ss=r

 

Call MSA for the best service. Those guys are super nice to talk to. Give them your czcc member ID for 10% off. Your's is 34425. I got it below on a screen grab.

Screenshot_20210209-101332_Samsung Internet.jpg

 

Link to comment
Share on other sites

Ok, thanks.  Didn't know about the 10% discount!  Man, I could have saved a lot this past year.

What are your thoughts on this gasket instead of the Nissan OEM one?  https://www.thezstore.com/page/TZS/PROD/classic19a/10-2525

It apparently comes with the performance headers purchase.  MSA link says:

Quote

"Special installation gaskets are included (do not use original equipment type exhaust gaskets with headers)."

 

Just called MSA.... backordered.  And they don't know when they'll get them.  The coating vendor has them backed up.  

Edited by Dadsun
Link to comment
Share on other sites

So, with MSA now telling me they are on back-order indefinitely for ceramic coated headers, I'm a bit stuck.  Anyone have other avenues they'd recommend? I could buy the uncoated for $300 then pay about $240 to get them coated, but that is just too painful on the wallet. 

I've been looking through eBay, but don't trust a lot of what I see.  Does this (see pic) make sense as a "square port style?":

huh-square-port-style-huh.jpg

 

Also, the MSA website description of their headers say: "The thick exhaust flange is flat machined to promote a consistent seal. It also prevents warping and eliminates the need for spacer height modifications."  Does this mean it will not have the raise lip around the square ports as my current one has? (see pic#2)

my-header-with-square-ports.jpg

Edited by Dadsun
Link to comment
Share on other sites

9 minutes ago, Dadsun said:

I've been looking through eBay, but don't trust a lot of what I see.  Does this (see pic) make sense as a "square port style?":

huh-square-port-style-huh.jpg

 

The outer 4 ports in the picture look pretty round to me. 
 

Compare it to the ports on your header. 

  • Like 1
Link to comment
Share on other sites

35 minutes ago, Dadsun said:

Also, the MSA website description of their headers say: "The thick exhaust flange is flat machined to promote a consistent seal. It also prevents warping and eliminates the need for spacer height modifications."  Does this mean it will not have the raise lip around the square ports as my current one has? (see pic#2)

"Machined" suggests that there will be no raised lip.  Many headers out there for the L engines have a flange that is thinner than the intake manifold flange.  So the yokes don't sit flat and you can have sealing problems.  Sounds like MSA has addressed the problems.

Those eBay headers look sketchy.  Four round and two square, not right.

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.
  • Who's Online   1 Member, 0 Anonymous, 254 Guests (See full list)

×
×
  • Create New...

Important Information

By using this site, you agree to our Privacy Policy and Guidelines. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.