mdbrandy's Content - Page 44 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. mdbrandy replied to 24OZ's topic in Open Discussions
    I just went out and crawled under my car to see what the slave cylinder connection size is. You're right - 17mm seems a little loose. However, I have a 16mm wrench (spanner), and it is too small! I tried 5/8 inch too, and it is too small. So, best guess is that it is a 17mm fitting, but since it is thin, it feels loose in a regular wrench. Usually, it's a good idea to use flare wrenches on this type of fitting, but mine only go to 14mm. I have to take it off soon anyway (I'm going to lift the engine/tranny within the month), so it's good to know :classic: . Anyway, that's my 2 cents. My car is an 11/69 240Z, but I know the tranny isn't original.
  2. I'm just starting my restoration, and if I can make mine look HALF as nice as yours (in a stock sort of way), I'll be happy that I did a good job!
  3. mdbrandy replied to 24OZ's topic in Open Discussions
    Rats! :stupid: You are of course correct. I missed 15/16, and then, in fact, I missed that I had switched to every 1/8 after 1 inch and was still only adding 1/16! (I don't think you'll see 1/16 increments after 1 inch anyway). So, I think I have the table right this time. Unfortunately, I can't figure out how to make a good table right now. I tried saving some HTML code to make the table, but it made the post too long. Oh well, probably not that important. Thanks for catching my mistake! Oh, and metric is MUCH better than SAE/imperial, but I'm a US-educated engineer, so I was brought up with both.
  4. mdbrandy replied to 24OZ's topic in Open Discussions
    I tried to download the first calculator and it wasn't available, but I put together a couple tables on a spreadsheet. The first gives the decimal inches equivalent for every metric size likely to be on a Z car. The second gives the "imperial" fraction in inches and it's decimal equivalent. Thus, for any imperial size you can look for a decimal equivalent in metric and see how close you are. As an example, look up 27mm and see that it is between 1 and 1 1/8 inches, or 19mm is very close to 3/4 inches, but is a little bigger, so a 3/4 socket probably won't work for 19mm, but just barely. If you have a sloppy 6 point 3/4 inch socket, it might work. Anyway, hope this is helpful. :classic: mm inches 4 0.1575 4.5 0.1772 5 0.1969 5.5 0.2165 6 0.2362 7 0.2756 8 0.3150 9 0.3543 10 0.3937 11 0.4331 12 0.4724 13 0.5118 14 0.5512 15 0.5906 16 0.6299 17 0.6693 18 0.7087 19 0.7480 20 0.7874 21 0.8268 22 0.8661 23 0.9055 24 0.9449 25 0.9843 26 1.0236 27 1.0630 inches (fraction) inches (decimal) 1/4 0.2500 5/16 0.3125 3/8 0.3750 7/16 0.4375 1/2 0.5000 9/16 0.5625 5/8 0.6250 11/16 0.6875 3/4 0.7500 13/16 0.8125 7/8 0.8750 15/16 0.9375 1 1.0000 1 1/8 1.1250 1 1/4 1.2500 1 3/8 1.3750 1 1/2 1.5000
  5. mdbrandy replied to 24OZ's topic in Open Discussions
    All the fasteners on a Z are metric unless they've been replaced by someone (like some that I've found while stripping down my car this week). Anything with a fraction (i.e., 11/16) will be "imperial" in inches. All the metric ones will be even millimeters (although I think I've seen some of the really little ones, like 4.5mm be in half mm). A few of the metric/imperial sizes are pretty close, like 13mm and 1/2 inch. You can convert by using 1 inch = 25.4 mm.
  6. I don't actually go to zhome.com very often, but I get their list digest every day or so.
  7. I spent 6 years in grad school at UCLA, one of my kids is a Santa Monica Native, and you COULDN'T PAY ME ENOUGH TO GO BACK THERE! I've spent some time in the San Francisco Bay area, and it's nicer, but I find that's where more of those "Fruits and Nuts" reside. Anyway, not all of us think CA is heaven, or anything close. Enjoy. I'll take the prairies.
  8. My 11/69 240Z already doesn't have the original transmission, and the one in the car has a problem with reverse. In addition, the PO has hacked the transmission tunnel opening for the shifter already, so there is now more throw room toward the front. I have a '78 280Z with a 5-speed in my garage ready to raid for any appropriate parts, and since the tranny alreadyisn't original on the 240Z, I figure I might as well use the 5 speed out of the 280Z. My question is if there are any other mods that would be needed to put this 5 speed into the 240Z. I know it'll bolt up to the engine fine, but is there any problem with driveshaft length, etc? I though about transplanting the entire drivetrain from transmission back, but I don't think I want to go that far. Thanks.
  9. I tried to get a screen shot, but it wouldn't work. From what little you can see, it is a big-bumper model, but looks to have the smooth bumper ends, so is probably a late 260 or early 280.
  10. Moore is an idiot. See: http://www.forbes.com/forbes/2002/1209/059.html?_requestid=2372&_requestid=6287 and http://www.spinsanity.org/columns/20021119.html for some critical takes on his "Documentary". And as for the bank gun scene, it was staged. The first link above gives: BANK: Moore says North Country Bank & Trust in Traverse City, Mich., offered a deal where, "if you opened an account, the bank would give you a gun." He walks into a branch and walks out with a gun. ACTUALLY: Moore didn't just walk in off the street and get a gun. The transaction was staged for cameras. You have to buy a long-term CD, then go to a gun shop to pick up the weapon after a background check. I'm not saying we don't have too much violence and guns in the US, but don't get your information from Michael Moore.
  11. My 11/69 production car has no rear defogger in the glass, and the console position for the switch is there, but was never cut out.
  12. mdbrandy posted a topic in Interior
    Well, I removed my dash tonight (there are a few rust holes high on the passenger firewall, and I didn't want welding to go on back there with the dash in). Before I even started, a couple pieces of the HVAC ductwork had fallen out from under the dash in pieces. While removing the dash, even being careful, a couple of the other sections essentially disintegrated. Extremely brittle. So, are these things available anywhere, or do I have to find used ones or fabricate something? A couple of them are completely unsalvagable - pieces less than an inch long.
  13. Right - it's a given that I'll do that work, and I'm already well along. Just more elbow grease and sweat. Luckily, there isn't much thick sticky undercoating underneath. Only a little. Most of the bottom is coated with a very thin grey 'something' that looks like a thick paint (although not very thick). Most of it is in tough shape and flaking off. It's not sticky at all - it feels like old paint. It may actually be the original undercoating - I don't know what was there originally. I've never had a Z that was original enough to care :classic:
  14. mdbrandy replied to mdbrandy's topic in Interior
    Both? Interesting. I'll see what the PO tells me about what he did.
  15. mdbrandy replied to mdbrandy's topic in Interior
    I know that the PO parted out a '71 (which I have several boxes of parts from), so if the early '71's had the knob, it could still have been from that. Does yours have webbing or springs, though? If you have webbing, then this is probably the original seat with springs transplanted into it.
  16. mdbrandy replied to mdbrandy's topic in Interior
    MikeW noticed in the picture I posted at the beginning of this thread that you can see impressions of what looks like webbing in the cushion in the bottom of my seats. So, either someone took the springs from a later seat and used them in the originals, or took the seat cushion from the early seat and put it in a later seat. Did the '73 have the lever that let the seat come forward more, or did that wait until the 260Z? These seats still have the big dial that tilts the back a few degrees. I'll ask the PO if he knows the pedigree of the seats.
  17. I wouldn't cut anything until I had the floor, but you're right about the lap versus butt joints, and without any welding savy, I wouldn't know which was best. OK then, hopefully the cutting isn't the costly part anyway.
  18. Ok, looking for some thoughts. I'm going to be doing at least some of the floor pans and frame on my 240Z. (see http://www.csar.uiuc.edu/~mdbrandy/240Z/240ZRust.htm for some of the worst of the rust). I've been talking with Charlie Osborne and will be getting some stuff from Zedd Findings to do the worst of it. So, I'm going to do as much of the teardown as I can, and get a pro to do the welding, since I've never welded before. My question is, how much of the floors can I safely remove myself (if any) before having it towed to a shop? I have plenty of air and power tools to cut about anything I want. If I removed pretty much the entire drivers side floor pan before towing, would that compromise the structure of the car too much and risk having the frame bend from just towing (flat bed, of course)? By the time I had it towed, the car will pretty much just be a shell - no interior or engine, so it's weight will be minimal. Some of the frame on the passenger side is also gone, and I'd remove most of the stuff that isn't doing much good right now anyway. Just looking to do whatever I can to minimize cost, while letting the pros do the important work. Thanks for any discussion on this.
  19. mdbrandy replied to mdbrandy's topic in Interior
    I've got a couple hundred so far, but I have to get them organized, reduced (they're 4 megapixel images) and posted. Hopefully this weekend or so. On the VIN, I think I had it right the first time :classic: HLS30 00215
  20. mdbrandy replied to mdbrandy's topic in Interior
    Wow. It's amazing what slips past you sometimes. I didn't look past the springs! You're right that it appears as though there was webbing against that cushion at some point. Guess that probably answers the question.
  21. mdbrandy posted a topic in Interior
    I've got a very early production 240Z, and I was just looking at the seats today. They are in quite good condition (probably been recovered). In my readings about the early Z's, I've come across mention of "rewebbing" seats, and seen pictures of early seats with webbing under the seat cushion that sometimes has to be reaplaced. What year(s) was this done in? I ask due to the fact that my seats do not have the webbing - they have metal springs (see pics). They are 240Z seats - no tilting lever, just the knob to change the angle a few degrees. I know that the PO had access to a parted out 1971 240Z (I have several boxes of parts he collected from it). Could these seats be from the 71, or would an 11/69 production car possibly have the metal springs? Ultimately it won't matter to me, since I don't intend to bring the car back to stock in every nut and bolt, but I'd like to be as close as I can. Thanks.
  22. Many years ago (1979 or so), I had a 1971 240Z. Sold it in 1981, but I just found a badge from it in a parts bin that apparently I've been carting around the country for 20+ years. It's metal. Nice and heavy. Unfortunately, there's a hole drilled in the center of it. Must have been mounted with a screw when I got the car, and I didn't put it back for some reason.
  23. I believe Mike W is right, that they can replace essentially the entire floor. If you have questions, you should e-mail Charlie Osborne at Zedd. I've been trading e-mails with him about my frame/floor, and he's been very helpful. Takes him a day or two to respond most times, but he probably doesn't spend 8 hours a day in front of a computer like I do! If you just have a few floor pan holes, and no frame damage, you've got a much easier job. Check that frame over carefully though.
  24. Charlie Osborne (of Zedd Findings - the floor pan supplier in Canada you mention) tells me that MSA actually sells his floor pans as premium floor pans. So they're not just close, they're the same thing! I can't compare prices yet, since MSA hasn't managed to send me their catalog yet...
  25. $800 for a dash, huh. Probably not . I'll search for those companies you mention, and probably go with the cover. I suppose you're right about the vinyl. That wouldn't be hard for someone to put back if they wanted. I'll think about it. I've got time :classic:. The motor is original with the right number, the SU's, etc. The only mod I can find is a set of rusty headers. The PO told me that he cracked the exhaust manifold, so just put headers on it. I think I can be quite happy with a well-tuned stock L24 in this car. My speed-freak days are over. Zippy and nimble is the name of the game now. Since the transmission is already not stock (the PO says it is a "truck transmission" although I don't really know what he means by that), I'm thinking about taking the 5 speed out of the 280Z I have. However, from what I've read, I'd have to cut a few inches out of the transmission tunnel on this early Z, and I'm not sure I'm ready to do that. Don't know what other drivetrain mods would be necessary if I did, either. I also have a 4 speed out of a 1971 240Z that I could use. The PO got access to a 71 parting out, and I have several boxes of misc. parts from it. Just thinking right now. Thanks for the input. I can use all I can get!

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.