Everything posted by mdbrandy
-
e-bay datsunz903?
I don't know if you've followed the threads on the "chrome Z", but what I was talking about was a '240Z' emblem where the 'Z' is chrome colored instead of white. They are apparently only on very early cars, and not on all of those, and are quite hard to come by. There are versions of the hatch "240Z" as well as the "flying 240Z's" on the pillars behind the quarter windows. These are not of any interest to you (since you have a 280), and are really only of interest to 240Z owners who like to collect the very early, odd, rare, etc. stuff.
-
1978 wierd ignition switch problems
Don't know if it'll help, but... I was just watching a Z-injection video from Z-Therapy yesterday with Kim Bough from Idaho Z-car. Apparently some of the latest '78 280's (and ZX's) used a circuit involving the oil sending unit and the alternator output as a kill switch for the fuel pump. You can tell if the oil sender uses the two spade plugs instead of the single bullet plug. This system replaced the airflow meter kill switch on the earlier FI system. I believe taking the oil sender connector off (and the alternator plug, I think) was the way to test it. That would at least explain the oil sending unit connection to the problem...
-
e-bay datsunz903?
Looks like I need to dissassemble a glove box soon....:cross-eye :classic:
-
e-bay datsunz903?
I'll put it on my "things to do" list. I might actually try to take apart the original one from my car (which the PO cut a huge hole in the back of), since for patterns, you really just need the outlines of the pieces, and I think those might be intact. I'd get better patterns off a taken-apart box. I'll see what I can do...
-
e-bay datsunz903?
I think I gave up on that one, but I did finally get one from Bob Zola that was used, but only a couple years, and is in essentially new shape. It was't cheap, but less than $50. I've thought about making them myself, since it is just cardboard, but I have had better things to do with my time! Maybe I should make patterns and post them or something...
-
e-bay datsunz903?
No, there's certainly no problem with bidding against someone on the board, and I've done it several times. In fact, I got a message back from kats and found out that I won some NOS braided heater hoses the other day that he wanted, but I got! However, if I know I'm bidding against someone on the board, and we communicate, if I don't REALLY want the thing, I'll back off and not run up the price if I can. If I REALLY want it, then to the highest bidder goes the spoils!
-
e-bay datsunz903?
I answered my own question by looking up kats profile. It's him. At least another club member might get it...
-
e-bay datsunz903?
Anybody know e-bay datsunz903? I was bidding against them for a chrome Z emblem, but it's getting a little too rich for me. Their profile says they're from Japan, so I thought it might be kats.
-
Very Very expensive 280
I'd say he's quite optimistic. I paid less than half his starting price for mine, and it's in at least as good, if not better shape. With a radio, working antenna, working clock, and only 3/4 of the miles.
-
Replacement Rear Covers for Headlamps?
How bizarre. Who knows. Without fiche assistance, it's hard to tell. Looks to me like the most likely thing is that the ones I showed probably came maybe from 77-78, and the earlier from 74-77, but they were made to be interchangable, and since they are easily-broken plastic, a lot of mixing went on. That would be my best guess, but without much supporting evidence. BTW, I am VERY jealous that you can just go out to a junkyard and look at first gen Z's. I go to any junkyards around here, and they look at me like I'm crazy. "Z what? ":disappoin
-
Replacement Rear Covers for Headlamps?
Interesting that these show up on e-bay just after we have this thread... http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2468821376&category=34204
-
Replacement Rear Covers for Headlamps?
The car that these came off of was a '78 as well. Production date of 5/78, so it was fairly late in the model year. My "good" '78 280Z is also a 5/78 car, and it has all the same bolts in the same places as the other one. Just doesn't have the plastic liner any more. And Tomohawk, you're not making a "big thing" at all - this is the kind of conversation that keeps this board alive - finding out all the differences between our cars, and sometimes tracking down why we have what we have!
-
Replacement Rear Covers for Headlamps?
Oh, and there are little clips that clip these to the wheel-well edge, in addition to about 8 screws from front to back. I didn't like the clips much.
-
Replacement Rear Covers for Headlamps?
Mine look pretty different. They are all one piece, and extend from the headlights all the way back to the little rubber flap that seals off the rear fender. Pic attached. The headlight area is at the bottom, and you can see some pieces of the rubber flaps attached at the top where the hand is holding them up. sblake01, thanks for taking your pic - it prompted me to get off my butt and out to the garage to take mine!
-
Replacement Rear Covers for Headlamps?
I don't see what I am talking about in my last post, although there seem to be some similar parts around 63830-N4200 on fiche 126-7. Looks like there were some changes over time, but there were protectors under the fender from about 1976 on.
-
Replacement Rear Covers for Headlamps?
I believe that he's talking about the front inner fender covers that I also believe only came on 78, and maybe 77 280Z's. The '78 parts car I took apart had them (and I still have them). The new '78 CA car that I have does not. They are plastic liners that cover all the way from the headlight bucket, go along the top of the fender (inside) and then back down along the rear of the fender well. They are attached to the inside of the fender with small bolts, which are still there in my CA car, so I assume it originally had the plastic liners, but they are now gone. The plastic liners I have are in mediocre shape, and I figure on trying to figure out how to fix the cracks and use them on the CA car, but it isn't a priority. Shall I take pictures?
-
What's wrong with Automatics
My first car was a '71 240Z with an automatic. Changed it out for a 4 speed after driving it for a year. I just love the shifting. I drive my 5-speed 280Z now, and when I need more than two seats, I drive my 5-speed Camry! Only when I'm forced to do the minivan thing do I give up my shifter. An automatic would sure be a lot more convenient around town, but who cares ! Drive what you like... Oh, and isn't the differential a little lower geared than in the manual (3.36 vs 3.54 or something?) Also, you get to deal with the dual point distributor on the automatic. If it was originally an automatic car, of course.
-
What size T-shirt do you wear?
XL works, but 2XL is better.
-
body differences question
If you can spend the time looking, you might find a transplanted CA or AZ Z-car in the US Midwest or East Coast. That's what I did. I had to drive 250miles to get it, but I drove it home from there, and now I just have to KEEP it essentially rust free. Mine was a CA car that someone moved to OH and then garaged for the rest of it's life. I've seen several others like it advertised in Chicago, Ohio, Michigan. Haven't paid much attention to cars on the US Eastern Seaboard. Good luck.
-
rust under hatch
Wow! Your site has undergone some changes Chloe! I didn't know you were into body panels now... Looks like I'll have to visit more often :classic: .
-
rust under hatch
Looks like the same part that Courtesy Nissan is selling for $113 and Banzai for $110. The $135 in the auction seems pretty steep.
-
rust under hatch
I see replacement panels on e-bay once in a while, and here's one cut off a parts car: http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2467506597&category=10076 Courtesy Nissan also is selling new ones: http://www.courtesyparts.com/Merchant2/merchant.mvc?Screen=PROD&Store_Code=CP&Product_Code=999M1-S30ZR
-
Major Backfire + Anyone seen my muffler?
All 280's are injected, and he says in his original post that he cleaned the injectors, so I suspect not :classic: .
-
Major Backfire + Anyone seen my muffler?
Check out the FI Manual at: http://www.72hours.net/~zcar/ For the problems you're having, it tells you to go through the ignition system first (which you've apparently done), and then indicates you might look at the air flow meter. Good luck.
-
Exhaust questions...
I suspect it matters whether you are dealing with square or round port heads as well. I assume that using a round port header on a square port head would not be the best idea. And Panchovisa is surely right that a turbo won't use a "normal" header.