mdbrandy's Content - Page 20 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. Isn't that where the air conditioning evaporator was installed in 240Z's? Aftermarket? Picture would be good. I've seen pics of 240's with a big box-like thing above the passenger's feet on the firewall, and it was the AC.
  2. Tomohawk, I thought you had a '78 280Z? Has it been modified in some way to have power steering? The 280ZX was the first Z model to get factory power steering, AFAIK.
  3. Hey, Andrew, if you go on a production binge, I'd take a set as well. Who cares about judges - these are our cars!
  4. #215 has clear hatch glass and an air filter box without damper. What are seat corner guards?
  5. Very interesting thought! I certainly can't verify it, but maybe someone can....or we can collect a bunch of data!
  6. Don't know if this will help in your discussions, but here's a pic of my radio from my early '70 car. Face plate looks just like the one in the e-bay pic. However, you'll note that the dash and map light are later style, since my PO replaced some things not knowing the differences between early and late cars. He was adamant, however, that the radio was original.
  7. I don't think this can possibly be accurate. Car number 5639 is on e-bay right now, and is a manual. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=2478887485&ssPageName=STRK:MEWA:IT Doesn't mean it couldn't have been automatic. I just looked at Humble's book, and that is what it says, but I expect it is a typo. I would gamble that it should be a number like 14870 instead of 1487. I believe that would make a lot more sense. There just weren't that many automatic cars made early. I had a 71 240Z that I bought in 1978, and it was an automatic. Changed it to a 4-speed within the first year :classic: . Wish I knew the VIN on it. There are only a couple differences in the wiring, I believe between auto and manual. The auto has a dual-point distributor. And there is some kind of relay in the ignition circuit. Anyway, I just can't see Humble's numbers being right.
  8. Just make sure you're recognizing the difference in the numbers we're talking about. The 060039 number is raised, and cast into the block under the exhaust manifold, down near the edge of the block skirt. The number on mine actually has a letter in it ("F"). It has always been my understanding that the actual block number is punched on the raised pad next to the L24 punch, on the rear, right side of the engine (passenger side for LHD, drivers side for RHD). But then again, I had never noticed these raised casting areas on the block....
  9. I still have an old Tweeks catalog that I keep just for fun. I think it's from 1997. And is that back or front Porch(e) stuff ROFL ?
  10. At least that seller has learned how to use his camera, and has gotten away from the "I wish I had a better picture for you" on every auction...
  11. Oh, I already have a fiche CD, and I walked in with part numbers. However, their computers have some superseding numbers that confused him, since their fiche only goes back to the S130. And I actually went there to see how much more expensive they were than Chloe - answer: a lot (20% plus or minus)! That's what I figured, but you never know. I was just looking for some tuneup stuff this time. Believe me, Chloe probably knows my credit card number by heart by now!
  12. I was at the Nissan parts counter here in ol' Champaign, IL yesterday, and the parts database only went back to S130 days. I had a heck of a time with the parts guy getting him to understand what an S30 was! Nissan guys need to take Nissan history lessons...
  13. RATS! Another nail in the originality coffin. I had assumed (read: hoped) my car had the hand throttle originally, since the PO that I bought it from actually disconnected the hand throttle because he considered it dangerous! He wasn't the original owner, though. According to him, he was the 3rd owner. Well, I checked my choke wires today, and they are solid. So now there's no way to tell if it was originally there or not. I guess I'll just have to assume...
  14. Amazing what you learn on this board. When 2-4-T-Z-Man started talking about a number on the block on the drivers side, I thought he was off-the-wall, but I just went out and looked at my block and there it is! E31 on the block, with a raised 9901F beside it. The actual block number is on the raised pads on the passenger side rear of the block (see pic attached - mine is block 2465). The 9901F must be some kind of casting run number or something. I've never seen it before. I have an engine out of a 1978 280Z sitting in my garage, and it says N42, and has a raised number that I can't read (position is bad, and I can't raise the block off the floor right now). It looks like 5 or 6 digits. So, I know it isn't the block number (i.e., not the XXXXXth block made), but I don't know what it is...
  15. Are you talking about the yellow zinc plated ring right under the horn button that faces outward toward the driver? Unfortunately, while I can see some vague remains of a circular stamp, I cannot discern any of the characters in the stamp. On the back of the wheel hub (reverse - toward the steering column), the characters "K15" are stamped into the black ring with a number/letter punch. But no other markings. Rats. At least it is a series I wheel with no cutouts in the spokes! I wonder about PO replacement on almost every part I took off this car!
  16. Much harder on a 280. All that "stuff" ends up inputting to the electronic fuel injection brain, which controls the injector duration. Most of it probably has to be left in place and working. Unlike the 240Z air injection system, most of it also doesn't take away anything from the engine's performance (the 240 air pump takes power to drive it).
  17. There's a date on the steering wheel? I'll look tonight!
  18. This is one amazing thread. Makes me want to go back through the boxes of parts I have stashed and bagged from #215's teardown, and search them all for dates!
  19. Great! Shorter is fine (I hope - there is plenty of wheel well clearance, just not spring clearance), wider is bad. Sounds like they should be the same diameter as stock. I won't be doing it for a month or more - if you get to it and find out differently, let me know! Thanks.
  20. Situation: I am going to rebuild the suspension on my '78 280Z over the summer (it definately needs bushings and shocks), and the plans include new shocks and springs. On my current setup, which has aftermarket wheels and OEM springs, there is probably about 1/8" clearence between the tire and spring on the front. This includes using about a 1/4" spacer on the wheels. Question: I'm thinking about the Tokico Blue shock/spring combination. Are the springs the same diameter as OEM, just shorter and heavier? Can't afford to have to replace wheels/tires due to spring clearance problems, and would rather not add more of a spacer. I assume the diameter is the same so they will fit into the spring perch, but I don't know... Thanks!
  21. Gentlemen: please read the tech link that Carl posted earlier. All will become clear. Panchovisa - the picture you posted is part of the tech discussion that Carl linked about 10 posts ago!
  22. If you read the tech article that Carl (Bambikiller) posted a link to a couple posts ago, you'll know exactly which Toyota silicone oil, including the part number.
  23. That's interesting. I'm planning on restoring to the stock emissions state, but I hadn't considered just having it for looks. Essentially, the only part of the emissions system that causes any performance decrease on a 240Z (that I can see) is driving the air pump. Everything else is pretty passive. Would you put a belt on the pump and disable it internally or something? Wouldn't want to actually drive it, or it wouldn't do any good to disable it in the first place... Hmmm....
  24. Ah. I hadn't considered that. So you can buy the new style cylinder and use either kind of rod? That's good to know...since I have one car of each type :classic: .
  25. Note, however, that the picture shown appears to have the early, adustable type pushrod, which is different than all slave cylinders after, I think, about mid 1971. Later cars went with a non-adjustable rod, and the fork did not have a hole in it. You need the slave cylinder with the adjustable rod, or it won't work with your clutch fork.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.