240260280

Aim for 14 at idle (richer is smoother idle but it stinks) Aim for ~15 to 16 at cruise Aim for 13 at WOT (12.5 to 13.5 range is fine)

Sounds like the car has diarrhea ...start at 47 seconds into the video.... it still cracks me up.

There are so many interactive parameters with side drafts that tuning may be challenging for some. The first crucial steps are to ensure the engine is in top form, the carb install is w/o air leaks, and that all linkages to the carbs start moving at exactly at the same time and they open the same amount to 90 degrees (where the stop bolt on the floor under the gas pedal will do its job).

Cheers Jims! @Zup, @S30Driver Having a good morning here. Janet is watching "Corrie" and laughing at me taking this picture. I'm now supping on the tea. Zeeelicious! Btw: The cutting board is from another nice Z friend: @Dr. 240Z

On a 240z I used the longer one. I needed a short one for a 510. It depends on where the manifold shaft ends.

I call it a Shepherds hook for obvious reasons. I think the proper name is torsion shaft. They may be shorter and adjustable on 280zx's

Something for you Hitachi 38mm SU guys and gals. Enjoy! HJL38W.pdf

CO is my hero!

They look like they will bolt and go. You may need to shorten the shepherd's hook rod coming from your firewall. They pickup the carb's rod between cylinder 4&5. Your configuration has it closer to the firewall.

I think the vacuum method is important as it can be replicated on a test bench. One can wet-flow water safely on the bench with the reference needle and old carb then replace against the modified needle as it is worked to measure differences in fuel flow for each station(vacuum reference). As mentioned, CO and I talked about these methods many years ago Another method is to have non-tapered needles of different diameters then drive with these to map a/f against rpm and vacuum. This will work nicely for optimizing the higher stations of idle and cruise. Again... this was from many moons ago. Note that each straight needle will suck in most load/rpms except for some sweet spots so the goal would be to find these sweet spot stations and assign the diameter of the test needle to these.

Camera or measure vacuum from nipple drilled into top of plastic plunger .....remember our discussion many moons ago of mapping vacuum in carb dome against load and rpm then replicating on a flow bench to "find station"? We have been there and almost done that https://www.youtube.com/watch?v=i2I5QKDDEDc Another:

This may be helpful. (no units). You will need to map air flow at rpm to vacuum then map vacuum against needle height (annular ring exposure) for various throttle openings. Then map the fuel flow from exposure and vacuum.

Putting wheels at joint helps.

In design, there are similarities, and then there are nearly identical copies. One occurs from convergent evolution, the other occurs from licensing, from disregard for licensing, or from expired patents. I don't know the history of these parts but they are all nearly identical so I assume they occurred via Prince's licenses. Regardless, our engines have too much in common with these early vintage MB's to be ignored; rather, I think, it should be proclaimed.

I like this compact design: https://www.ebay.com/itm/Datsun-240Z-Abarth-endsilencer-NOS-2-5-exhaust-system/222734995837?fits=Model%3A240Z&hash=item33dc0a517d:g:JnYAAOSwc~laFu7r&vxp=mtr

Here is a photo of how to pry valve down so that you can slide rocker in place or out:

These early Mercs do not seem to have the locking nut like on the Z's

Some of the Merc's are 14 mm and some are 17mm go figure https://mercedessource.com/store/m130-m180-special-valve-adjustment-17mm-socket-wrench

14mm and 17mm are the L series sizes. I'll try and find out what the M-180 uses.

First M-180 was built in 1946:

Spot on Steve & Fred! The photo was taken in May 1972!