Jump to content
zKars

When you haven’t done it for 40 years....

Recommended Posts

9 minutes ago, zKars said:

Well it took two days, about 8 hours of work, and a lot of sweat (it’s actually a heat wave here right now, +23C yesterday) but I did it. Boy is my right arm sore.

I got this thing started. Was last running in 1981.  Yup

Wow, your '71 240Z sat for almost 40 years without being started - incredible!  Just think about that for a moment, the car was only 10 years old when you parked it.  Congrats on bringing the old girl back to life! 

  • Like 3

Share this post


Link to post
Share on other sites

1 hour ago, zKars said:

Heater valve leaks. Good thing there are holes in the floor to let it out on the ground.

That valve and the dense PO that kept adding coolant without considering where it was going caused the hole on mine. LOL

20190624_094447.jpg

 

Edited by siteunseen
  • Sad 1

Share this post


Link to post
Share on other sites

Clutch master and slave are new. Wouldn’t push fluid to the slave. Turns out the soft line was plugged with crud. Fixed that, and now the clutch works. Can technically make it move under its own power. SU’s need to be dismantled and cleaned, the jet tubes are frozen and it’s tough to get the mix rich enough. Runs but way too lean. Will take care of that this evening. 

It has to move into my yard for winter. Don’t feel like pushing it uphill, so it will get itself there, even if I use the starter motor to do it. 

  • Like 3

Share this post


Link to post
Share on other sites

Jim,

You are a bear for punishment!  

No idea what you paid for it, but I'll bet it was a pretty penny particularly since it came with a trailer hitch.  Just don't see that every day.

Good luck with your latest project.  

  • Like 1

Share this post


Link to post
Share on other sites
5 hours ago, siteunseen said:

That valve and the dense PO that kept adding coolant without considering where it was going caused the hole on mine. LOL

20190624_094447.jpg

 

I know Mr Arnett, it's a cancer. But I have it in remission. Thankfully I can get a new pan for that side.

  • Haha 1

Share this post


Link to post
Share on other sites

18 hours ago, zKars said:

 

Boy is my right arm sore.

 

 

You should switch hands once in awhile, eh?

😁

 

Edited by Racer X
  • Like 1

Share this post


Link to post
Share on other sites

Jim,

I'm amazed you found the engine to be so clean after four decades.  Coincidentally, just last week I began disassembly of an old Chev 327 V-8 (I know, I know, sacrilege on this site; forgive me).  The fellow I got it from believes that it last ran in (another coincidence) in 1981.  The oil is disgusting.  It is sludge.  Days after I began stripping the engine, there are still bits of black greasy stuff falling off the block.  I used a spoon to get some of it off the top surface of the heads. 

I have to admit, I've never before taken apart an engine  that has been idle for so long.  Any chemists out there know why Jim's engine would be clean, while mine is such a mess?  

 

Share this post


Link to post
Share on other sites

 One possibility is back in the days of 327s, :love: many old timers were still using non-detergent oil. If you didn't change the oil frequently, a massive amount of sludge would build up. I've seen it so thick that the head bolts were completely covered.

  • Like 1

Share this post


Link to post
Share on other sites

Mark,

Bingo!  I think you nailed it.  Long time since I've been offered the choice of detergent and non-detergent. 

You mention head bolts covered with the stuff.  Mine were almost that bad.  I could see them, but had to scrape the sludge off  to get the socket to fit.  

BTW, my 240 is up and running, so I hope I won't be banished from this site for apostasy.  The 327 is for my newest project, the restoration of a 1965 Grant King-built oval-track sprint car.

Cheers

  • Like 1

Share this post


Link to post
Share on other sites

Final chapter for now.

Had to clean the carbs more thoroughly than I initially hoped. The jet tubes were not moving on their own, so couldn’t set richness or chokes. It was massively lean, would bog terribly just blipping the throttle, so I took them off last night and cleaned them up. One jet tube had to be pin punched with a ball peen hammer to move it. No damage, after cleaning and lubing, they now work just fine. 

I drove it quite nicely into its parking spot in my yard under its own power. Clutch felt perfectly fine. Would have loved to take it around the block and get it in second, but with no brakes, no way. The master has a layer of probably the stickiest black goo in the reservoirs I have ever seen. Will have to soak for ever. It has the nice early “Front in the front” master, would like to keep it.

The clutch slave soft line was plugged with crud. Couldn’t bleed the clutch initially, so I suspect the rest of the brake system needs more cleaning and work than I’m prepared to do this round. I have “peachy” to get ready by Christmas and there’s a storm-a-comin’ this weekend that will snow in the fleet for the winter. 

Thanks to Jitensha (Kevin) for helping with the car rodeo today and doing a great job of wheel chock placing when needed.

  • Like 3

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use. We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.