mdbrandy's Content - Page 28 - Classic Z Car Club Skip to content

mdbrandy

Community Member
  • Joined

  • Last visited

Everything posted by mdbrandy

  1. Well, I found a nice post buried 5 pages deep in a search: http://www.classiczcars.com/forums/showthread.php?s=&threadid=6608&highlight=steering+wheel It has a lot of interesting opinions already there. If anyone has anything to add, let me know!
  2. The steering wheel in my '78 280Z is slightly sun damaged on the top, with a small split, and I'm thinking about putting an aftermarket wheel on the car. I'm not too concerned with originality in the 280 (I have the 240Z for that!). It would be nice to keep a Z logo of some sort, though. MSA has some wheels that have Z logos, as well as a variety of other wheels. So, my question is, for those of you into aftermarket steering wheels, what would you recommend? The car's a daily driver, so it has to be something "ergonomic" that doesn't exacerbate the already heavy steering. Thanks for any opinions.
  3. Before October when I bought my newest '78 280Z, I was looking for "low or no rust" daily drivers, and I was looking at ZX's as well as original series cars. I saw three or four ZX's with VERY low mileage. One had only about 30 miles on it. There was one in St. Louis with only a few thousand, and I think it was a ZX race version (280ZXR?). You're right, I really wish someone had saved a few examples of original series cars with low miles, but it looks like people didn't think about it much until the ZX's. Or maybe the few low mile original series cars are just not for sale .
  4. The problem is, that if you buy a car like that, you're hesitant to drive it! Good museum piece or show only driver.
  5. Every Z driveshaft I've removed, from 240's and 280's has just slid out of the transmission. No bolted or clipped connection or anything. Sounds like as you are pulling the shaft out of the tranny, you're pulling down on the back end of the shaft and binding the splined shaft inside the transmission. You have to pull it straight out, and it has something like 4 inches of slip-in splined shaft on the transmission end of the driveshaft. That's about all I can think of that would keep it from coming out. Good luck.
  6. So nobody's ever seen an original air cleaner that isn't orange? Makes me feel better that it isn't just something that I've missed in my "Z-knowledge". :classic: Maybe it is just rare or unusual if it is really original.
  7. I thought all the 240Z air cleaners were orange. Were some of them different colors? The '73 in this e-bay auction has a blue one and claims to be original: 73 240Z Just wondering.
  8. What's missing? If you're talking about the hand throttle, they are very difficult to come by. That's mostly because almost no US market cars had them. Only a few of the earliest 240Z's had them here. And most of them actually had them removed by the dealer because they were believed to be hazardous by US drivers! Anyway, if you're talking about the hand throttle, don't worry about it. Your car very likely didn't have one to begin with. If you're talking about the choke handle, there are a couple on e-bay right now.
  9. Actually on the SIDE of the center console? You got me. I can't come up with anything like that.
  10. See the attached picture. The lever on the left is the choke. The one one the right is a hand throttle, which you will not have.
  11. From your description, it sounds like the choke lever.
  12. Probably depends on your wireing harness connection. I just took off the one on my 1978 280Z parts car, and it has a plastic connector with two spade connectors in an "L" pattern. I believe the earlier ones had a single bullet-type connector (my 240 has been disassembled long enough that I don't remember anymore, but I think so). I assume that guages get the same signal from each of them, and I believe that the block "screw in" is the same, so it probably comes down to the connector type. FWIW
  13. Boy, I wish there was something like that around here. Even though I do most of my work on the Z's myself, it would be nice to have Pro's to do some of the harder stuff. Nobody around here wants to touch restoration work.
  14. Ben's right on the bushings. The shifter in the '78 280Z I bought 6 weeks ago was very sloppy although the actual shifts seemed tight. New bushings from Midwest Z, and it is tight all around now! Wish they weren't just little plastic jobs though. Bet they don't last but a few years...
  15. If you decide to cut and weld, I am madly trying to get my '78 280 parts car apart so I can get it out of my garage and my new 280 into the garage. That portion of the right rear fender looks pretty good from what I can see so far. If you want it before I have the carcass carted off to the recycler (hopefully within a week or two), it's yours for the shipping. By then, I should have virtually everything stripped off the car. But listen to the guys in the previous posts. They know a lot more about body work than I do. Cut and weld might not be your best bet.
  16. Make sure your wheel wells are in good shape too. I had a '75 280Z that at the end (just before I sold it), I could barely drive because of the fumes. I believe it was because, if you took off the interior left quarter trim, you could see the road down through the wheel well past the radio antenna . Kinda hard to seal that off with rubber... Wasn't obvious from out side the car. Had to get into the wheelwell and look. FWIW
  17. Cool link Chloe. I hadn't seen this one before. Thanks!
  18. What year Z is the new dash from? The wiring harnesses did change over the years. You could, however, take the harness out of your original dash and put it into your new dash. That ought to solve your problem.
  19. mdbrandy posted a gallery image in Member Mugshots
  20. It uses a bimetallic coil that opens and closes oil passages depending upon temperature.
  21. The factory manual for my '78 mentions silicone oil, so the description in the link is consistent as well. Thanks for the link!
  22. Thanks. I started that other thread because this one was getting kind of off that topic. ZmeFly then posted the definitive answer!
  23. I have no pics of me IN the Z, but here's one UNDER the Z. Be warned. It's not pretty....
  24. Very true. Obviously, the "normal" fix for this is replacing the clutch. I have the factory manual and about 5 other manuals of various types on Z's, and NONE of them even gives a good diagnosis section for the fan cluch, much less how to repair it or any actual data on it. They all have the same very nice drawing, and a description of the theory of operation, but nothing else. Oh well, unless the real data surfaces, then using the wrong oil weight can't hurt it much, since it doesn't work anyway! Just a waste of time to rebuild if it doesn't work after...
  25. I still couldn't see it until I cropped and blew up the pic. I finally see what appears to be the red dot...

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.