astrohog's Content - Page 3 - Classic Z Car Club Skip to content

astrohog

Supporting Member
  • Joined

  • Last visited

Everything posted by astrohog

  1. WOW! That is pretty cool, Jim. Our cars were born so close to one another, but my warranty card is not in my name!
  2. Will be interesting to see how this auction plays out. Not a lot of fanfare for this car which looks to be in very good, original condition.
  3. Fugly comes to mind!
  4. You know what they say......."Garbage in, garbage out"
  5. Yup. Pretty much sums it up! 😄
  6. Nope, that is an actual picture of the original owner of my car when we were going for a test ride........ 😉
  7. astrohog replied to Patcon's topic in Wanted
    Mine did as well, our cars were built within weeks of each other.
  8. astrohog replied to Patcon's topic in Wanted
    My 12/70 car has the heat riser.
  9. Where are all these bots coming from?
  10. Fixed it for ya! 😁
  11. .....
  12. astrohog posted a topic in Wanted
    Looking for a close ratio 5 speed. I've seen a few listed here, but can't seem to find them now (plus they were over a couple years old). Hope someone here has got one that I can take off their hands!
  13. Planning to swap an R200 into my Series 1 car (12/70 build date) and am looking for the mustache bar, front diff mount and insulator and the rear transverse link mount from a later 280Z that came with the R200.
  14. Sent PM
  15. OK. Just got the last of the plugs in. I like the M16 x 1.5 low headed plugs to fill the inside ports of the intake when one has removed the water heating. Purchased them from Belmetric.
  16. Well, Here I am, a year late, but better late than never! I paid $3,000.00 for my all original, 100,000 mile, 12/70, 1971 240Z in 2006.
  17. Okay, so I've received various plugs and set screws from both McMaster and Bel-Metric. I ordered 1/8 and 1/4 NPT, 1/8 and 1/4 BSPT, M12 x 1.50 straight thread and M12 x 1.50 tapered thread, and I am still a bit confused! I won't hold you hostage until the end, I'll give you what I THINK the holes were from factory, and then I'll provide some pictures and notes from my "testing". I think the factory balance tube (US market 240Z) came with 2 ea. - 1/8" BSPT and 5 ea. - 1/4" BSPT holes BALANCE TUBE 1/4" BSPT HOLES it was clear to me that 1/4" NPT is too big, couldn't really even get a thread to start, so it makes sense that, 1) One COULD force 1/4" NPT into the holes in the soft aluminum and create some sort of "seal", and 2) a hole that had been "buggered by a previous (or current!) owner could likely be salvaged by tapping to 1/4" NPT. The 1/4" BSPT plugs I have encounter resistance at 1-1/2 turns and are fairly tight at 1-3/4 - 2 turns. This leaves them sticking out farther than I would like for a clean, plugged look as I would like them to be as close to flush as possible. The M12 x 1.50 straight thread, socket set screw I tried fit very loose initially, and threaded quite a ways in (farthest of the three options I tried) before finally hitting resistance. I feel like it MIGHT have finally created a "seal", but not ideal in my opinion. The M12 x 1.50 TAPERED plug encountered resistance at about 3-1/4 turns and was fairly tight at 3-1/2 turns in. This left it pretty close to flush to the surface and provided a good seal and I think this is what I will be using to plug 1/4" BSPT holes. (see pictures below) BALANCE TUBE 1/8" BSPT HOLES it was clear to me that 1/8" NPT is too big, couldn't really even get a thread to start, so it makes sense that, 1) One COULD force 1/8" NPT into the holes in the soft aluminum and create some sort of "seal", and, 2) a hole that had been "buggered" by a previous (or current!) owner could likely be salvaged by tapping to 1/8" NPT. The 1/8" BSPT plugs I have, encounter resistance at 1-1/2 turns and are fairly tight at 2 turns in. This leaves them sticking out more than I would like for a clean look (see pictures below) now I want to experiment with M10 fine thread (both straight and tapered) in the 1/8 BSPT holes INTAKE MANIFOLD WATER HEATING HOLES The outside (inlet and outlet) holes come from the factory with 1/4" BSPT holes Again, the 1/4" BSPT plugs don't thread in very far and sit proud. The M12 x 1.50 TAPER thread plugs thread in farther and sit pretty flush for a clean look. the inner holes (two holes on the inside of each part of the two-part manifold that connects the manifold halves with "bushings" and metal tubing) come from the factory with M16 x 1.50 STRAIGHT thread. I have some M16 x 1.50 straight AND taper plugs coming to try in those holes. I'm now thinking that a straight-threaded plug with a low head and Loctited, may be the ideal ticket for this hole since there is a machined spot to accommodate a bolt head. Heck, any old M16 x 1.50 bolt will work here! Keep in mind that these holes, if not being used (not connected to water lines), can stay open, they do not need to be sealed/plugged, as they will not affect anything other than keeping the intakes warm on initial start-up in cooler weather/climates. I just want to plug them for aesthetic purposes. Here's some pictures to clarify my rambling!
  18. Just ran across this one and thought I would share. I can't recall seeing one that was as factory fresh as this one! Color combo is much better when new! 1972 240Z 9500 miles
  19. Happy Thanksgiving to the Z family!!! I am grateful for this group!
  20. My 12/70 has the flapper. And I'm REALLY late to the party! I just picked up an air cleaner housing that only has one hose barb coming out of it (I'm assuming it is for the valve cover breather hose?), has the filter retainer ring on the inside of the filter and there is no sticker, but has sticker residue on the top. What sticker would have been there, and what production dates of cars would have come with this style of box? Jan. - July '70 cars?
  21. Anybody remember this one? White Lines
  22. Yes, I understand how they are designed, I just wanna use them how I wanna use them! LOL I really wouldn't like the look even if the heads DID bottom out, still kinda klunky looking. The BSPP plugs on the other hand (they have a lower profile head), look pretty good, but they won't bottom out in the tapered holes.....so I guess I could tap the holes to a parallel thread and use thread sealant. I think you are right though, once I get all the holes I need to plug measured, I will order the allen screw type.
  23. OK, here we go..... The threads on the balance tube all seem to be BSPT (1/8" and 1/4") The threads on my intake manifold where the water lines used to go are still a mystery. I have a feeling they are just a metric thread (not pipe thread), so I will have to do more investigating when I have an assortment of metric bolts to try. Also, my thermostat housing is at my storage, so I cannot check those outlets right now, either. I guess everything is a process......stay tuned! Here's my new dilemma; The pipe plugs I ordered from McMaster for sizing purposes are external hex head, and they do not thread deep enough into the balance tube for the head to bottom out and seat on the flat of the balance tube. Not the clean look I was going for. I think I'll try the internal hex drive (like a regular socket set screw) plugs and hope they sit flush or a little recessed when seated. If I don't get a good, clean look that I like, I may have to weld the holes up and grind them smooth. Oh, the lengths we'll go to for these cars!!!! LOL
  24. Yep, I read that one and that is what caused my post. I have the oil pan from the turbo motor, and I have the oil pan from the original L24. I can use either, but they both need re-habbing before I can use them. I didn't want to have to re-hab both of them at this time, but I think that is what I'm going to do, as they will both need to be done at some point anyway. Since I have the pan out for cleaning up, I have the ability to modify/change/omit the heat shield from the turbo pan. Can you explain what part interferes with the header? I'm thinking I may be able to retain some heat-shielding of the gasket and still fit the headers? I'm actually considering just using the MSA header I have for now until I can save some more dollars for the ZStory headers and hopefully, the tariffs will expire as well! I've also read that the turbo oil pan may not fit into the 240 because of the sump being in a different spot from the 240 pan, and causing interference with the crossmember, but I haven't been able to confirm that either.

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.