All Activity

Here's the start. Notable that there's no way for too much voltage unless there's a problem with the voltage regulator. I think he meant current. The best way to handle disparaging comments is with postitive comments. Take the high road.

That is because you do not completely disassemble your switches before restoration. You also have not unlocked the hidden performance upgrade in your turn signal switches due to certain modifications. It's amateur night at best.

It was nice to see truthful information about this issue from another experienced person to cut through the character assassination that passes for knowledge from some of the members of this page.

@Zed Head Is there a test I could do if I jack the car up and pull the e-brake a few times or would that not tell me anything?

Yes it's 19 on the drawing.

You won't know until you use it.

19? https://www.carpartsmanual.com/datsun/Z-1969-1978/axle/rear-axle-drive-shaft/19 https://www.google.com/search?q=39628-E4100

Have you tested or tried to rebuild the horns?

Absolutely! Will take me a little while, but the quality and sound were great on the test run!

I put a set of Jaguar horns on my '83 Turbo back in the day. Great sound and always surprised people that is wasn't the typical Japanese "meep!" I wish I could remember what model I lifted those from.

Yep, it's right 'chere:

@Mcbtuba Any chance you can post a photo of your install? I like the Retrosound stuff they've been coming out with lately. Might be nice to install one myself.

I believe these bolts are 10mm x 125 threads and 22.23mm long. I'd like to replace those as the 54 year old rusted almost stripped ones that I removed I'd rather not put back on. Does anybody know where I can find these special nuts, bolts & lock washers? Most likely they are hardened as well. Thank you in advance for any tips or directions that may come my way.

Steve, though I’m sure you’re not surprised, it worked! Thank you!

@Zed Head If I know the adjustment gear turns since I backed the pads in, does that mean the system is good? I really don't want to fight to pull the drum off again.

It is also important not to mix adjusters from one side to the other, as I believe they are handed

Thank you Zed, I didnt take any good pictures of the transmission yet, so i zoomed in on from another photo. I think it is the 4 speed F4w71B. I think i remember seeing the plate with 6 bolts infront of the shifter. Doing more research mine is a 01/77 build so its more than likely a 4 speed. Once I'm closer to finishing the build i think i'll try to buy a 5 speed.

It will even both sides out. It affects the adjustment of the shoes so will affect the brake pedal. Can't remember for sure but I think that you will also feel the brakes apply a little higher on the pedal after a notch gets taken up. It's one reason that seems rational for converting to disc brakes if you're in to precise brake performance. Should emphasize though that you need to be sure the parts are clean, lubricated, and not worn, in order for the system to work correctly. You can test it with a drum off by pulling the cable by hand and watching the parts move, I think.

You could get either in a 77. The numbers don't mean anything. Your picture is not very good. Here's some FSM stuff that should help.

I'm in the middle of a restoration and I want to confirm what transmission I have. I would get markings off the trans but I'm out of town. Is it a 4 or 5 speed? Came out of a 1977 280z. When driving it I only had 4 gears but I felt like there should have been 5 but it wouldnt go in.

Thats a very good bit to know and it totally makes sense. I'll have to keep that in mind when I finalize the fuel system. Since my fuel tank and mount is currently toast, I'm going to sub in a 3g fuel can for now. I've got the pump installed for now, im not happy with how it mounts so ill have to figure something out. I havent had a chance to look for a right angle nipple that might be able to save me some space. The rusty tire tub came in useful as I was able to run the fuel lines through it. Its just temporary to see if I can get the car running. Since I got the pump wired up I decided to see if pump would run and I got nothing. I dont think it has power. I didnt spend any time diagnosing it, I was happy to accomplish the little bit I did. I'm going to flip through the FSM and see what testing procedures they have. Obviously the fuse and maybe a fuel pump relay are at the top of my list. On a side note, I am having a really hard time with my shrink tube terminal connectors and I was wondering if you guys can suggest some better ones. I purchased these amazon terminals and I just cant get them to crimp for a damn. I have 3 different types of crimpers. The old fashion ones and two of the ratcheting kind. I had a couple of the normal terminals and they crimp really nice and tight, but for some reason the shrink tube ones just wont bite. Maybe I just have the wrong jaw. Can anyone also suggest some decent vacuum line? Im not a fan of the silicon ones and all the line I can find is super thick.

Green/White = Positive for gauge lights Red/Blue = Returns gauge lights to the rheostat (gauge light dimmer) Blue = Accessory (Key Switched) Constant power would be come from the cigarette lighter (Blue/White)

Awesome, that's exactly what I was hoping to hear, thanks @Zed Head. Does it matter that one drum's shoes are currently further-in than the other side's since I didn't need to loosen the passenger side's shoes to get the drum off/on but I needed to loosen the drivers side's? Basically I'm asking if the drums will permanently be unevenly tight, or if the automatic adjustment system will handle tightening the drivers side only so it matches the passenger's side and if that system has an adjustment limit. As an extreme example, if the drums are pulled all the way in using the adjustment wheel, would pulling the emergency brake 100 times get the car to the same/correct shoe adjustment level as if someone followed the FSM using the method you noted (albeit just taking considerably longer by contrast)? Also, the auto adjustment system is only calibrated using the emergency brake and not the brake pedal, right?