EScanlon

Check the resistor by the coil. You don't mention how the engine operates ABOVE 4k rpm, and going off ttz's post, I presume that yours does the same. The resistor is open coil with a ceramic heat holder, it is DESIGNED to burn off excess electricity in the form of heat. That means that this wire can eventually oxidize and break. Try this, connect the two wires going to the resistor, you'll be sending the full 12v of juice to the points during this time, but you're only going to check things out. Operate the car at the trouble rpm and see if the problem reoccurs, is the same or ? If the car's problem has changed, you have all or part of your answer. Then fix, and be sure to restore the resistor back into the circuit. Although there are various posts regarding removal of the resistor it's only really recommended if you are NOT running points. If you ARE running points you'll pit them out quicker without the resistor than with. Also check the connection for the coil LOOP at the back of the tach. If the plastic harness that the loop is held by is gone, it can cause the wire to slip, and cause bad or no readings. 2¢

Due to the shape of the 8 track tape, the faces of most players are very similar. About the only differences came from what type and quantity of knobs they had above the opening. The differences between the one he has a picture of and the "original" one, from what the Microfiche shows, are few. Then again the microfiche doesn't show much detail. 2¢

I also have not heard of this mod. Most people are looking to get a good dash, and the older model ones are getting scarcer. But apparently you have access to a good old dash and are looking to swap it out. If I recall properly, the ZX's have enough of a difference in the shape of the firewall, the angle of the windshield and the height from lower edge of the windshield to the top of the transmission tunnel that it might well be very hard to do so. 2¢

If you have the Factory Shop Manual (FSM), it will show you the best points to put Jack Stands under. Be careful of the lower A Arm of the Rear suspension, yes it will hold it, but you CAN damage the arm. There is a frame rail in front of the rear end which will hold the car up very firmly and nicely. If I recall, that's one of the points recommended in the FSM. In the front, again careful of the suspension parts. Again look for the frame rail and avoid the metal for the rod that connects to the frame there. Right behind that, is the other one if I recall. As far as lifting the car with the scissor jack, as MikeW pointed out, there should be a diagram on it. If there isn't, look at the seam under the rocker panel as he explained. You should find two reinforced spots on the seam one just in front of the door and another just behind the door. Those are your jacking points for the front / back of the car. Don't be surprised if the scissor jack raises the complete SIDE of the car, both front and back at the same time. That's why you want to make sure you chock BOTH wheels on the other side. Don't just trust that the Park position on an automatic tranny or the parking brake will hold it. Put one chock in front of the front tire and one behind the rear and KICK them in so they grab. You DON'T want that car to shift and topple the scissor jack. Hope this helps. Enrique

Are you talking ALL rains, or are these the FIRST rains to hit your area. Up here in the Pacific NW we get a lot of rain, so much so that we don't tan, we rust. However, during the summer months we usually get a good long dry period. When the rains begin again, in the fall, we find that the roads are "slicker" than later on in the winter. The reason for that is that there hasn't been enough rain to wash all the films deposited on the roadway during the summer. Oil, Anti-Freeze, Grease, dust, dirt and whatever that cars seem to shed during the summer will create a nice slick coating on the roads the first few days / weeks depending on how much rain and how fast. Go driving around then like you do in summer and you'll slide. Drive around like you will later on in winter, when more rain will have fallen and you've gotten used to it, and you'll slide. When the rains first start, it's time to be extremely careful as ANY car could go for a whooops slide. FWIW

Here's the larger image: http://www.classiczcars.com/photopost/showphoto.php?photo=2599&size=big&papass=&sort=1&thecat=500 Here's the smaller image: http://www.classiczcars.com/photopost/showphoto.php?photo=2599&papass=&sort=1&thecat=500 I went for a small pointy oval. I felt it complemented the headlight covers and the overall look. 2¢

Actually, P/N 29220-E4125 or 29400-E8725 were for an 8 track stereo radio as a factory installed option (with TWO speakers even). The microfiche doesn't show a good detail of the face, but from the fact that the one you have does NOT have an antenna switch on the upper right, I would say it's more than likely an aftermarket one. The antenna on the 240 was a manually operated electric antenna. i.e. you had to push the button in one direction or the other to get it to work. A Fully Automatic Antenna detects the radio being turned on and off and actuates accordingly. FWIW Enrique

These were quite popular in the mid-70's. You stuck your 8 track cartridge in the player and you played all 4 tracks (2 ran simultaneously so you had stereo) and you listened to the whole album. Pretty nifty concept, same one used as the radio stations to play songs and commercials. Hardest thing you'll have with that is getting tapes to play in it. To hook it up, you've got the schematic on that decal on the chassis. Hook up a wire to the positive side of the battery and put that in the Red wire, then a black to chassis ground, and one wire each to the left and right speakers. The other terminal on the speakers goes to chassis ground. Whether it's the original or not? Could very well be. If you need any more info on the operation of it, I used to sell car stereos and can pretty much tell you what to look for. Enrique

Well as 24OZ's picture shows, there actually was a fair amount of silver trim on the original consoles and dashes. Sadly, it rarely survived more than a few very light wipings with any kind of dash cleaner. I researched just about every picture I could find showing consoles and dashes to determine what "should" have been trimmed. I had a few doubts, but decided to use logic to "fill in the lines" where I felt the details of the car called for the trim. I welcome any comments, and would love it if someone has pictures that confirm / deny what I've done. Enrique

With regards to the chrome trim on the door panels, I agree, don't use paint or anything except that film. I've not had the need of it, since I cheated and bought a pair of NOS panels. But the heavy duty trim tape for boats sounds like it would work better than Bare Metal. Since the original post dealt with the trim on the Fuse Panel Cover, which has a thin line around the area for the warning lights, that's what I responded to. Look in the gallery and you'll see my center console. Most of that was initially done with Bare Metal Foil and it looked excellent. However, in just a few weeks, I had already had a couple "oops" items show up. Just from simple activities, that's why I investigated the other stuff. FWIW

I went the nail polish route out of desperation. Desperation out of having the Bare Metal Foil continuously peel off and wrinkle etc. I had tried the silver paint from Model Master but I could see the brush marks. I couldn't see any of the brush marks when I got done with the Nail Polish. Since it hasn't chipped or come off, I can't tell you if it marred the plastic or not. It does clean up with Acetone, and Acetone can damage the plastic, so I would advise caution. But again, since it hasn't FAILED, I haven't checked to see what damage has occurred using it, and is hidden beneath. I mentioned the name of the brand, hoping that you might be able to find that in a local drug store or whatever store in Australia may have Sally Hansen Nail Polish. In my international travels, I've been amazed at how "quickly" female products cross borders as opposed to "male" products. (Nail Polish, Pantyhose, Perfume as opposed to Motor Oil Additives, Tools, or in this case Spray or Bottle Paints.) FWIW

Nice Job, Nice Color, Excellent Shine, Looks Flawless. Now you're in deep trouble. You'll have to make sure that everything you do from here on out fits in with this paint job! Keep the pictures coming...... Enrique

I've tried the following methods: Bare Metal Foil. Looks= EXCELLENT! However, not very durable. Especially when you are trimming it to fit just on the raised edge. Model Master Silver Paint. Looks = Good to Excellent! Be careful of smudging and / or having to remove stray paint drops. Those paint drops will literally allow the metallic particles to ETCH themselves into the plastic like if you had sandblasted them in. i.e. you can never REALLY remove silver paint from black plastic and not leave some form of silvery stain, without having to sand or strip. And here's the kicker: Lately there have been various shades of nail polish (Yes, NAIL POLISH), which fit this job EXCELLENTLY. Sally Hansen's line of Metallic Polish are some of the best paints for touching up silvered trim / accents. They only cost a couple bucks and you can get them in SHADES of Chrome. I tried them on a couple pieces of edging that I'd done with Bare Metal Foil that chipped and needed redoing. Can't tell you how they ended, because they are still ok. 2¢

Ben: From your description it sounds as though you are referring to the 73 and later panel above the shifter and below the heater control panel. If memory serves me correctly the other light you are referring to is the Choke ON warning light. Anyone else have an opinion on that? 2¢

Ditto Bambi! 2¢ Victor, whoever "He" was he either confused your year of car, or didn't know this quirkly little factoid. The Z has dozens of little unknown quirks that apply to one year and not the others. Stuff that would seem to be "common knowledge" turns out to be interesting discussion between people who enjoy those cars. You know there ought to be a place where we can discuss that stuff...... Just to point out some of the "obvious" ones. These observations are based on U.S. market cars, and as discussion on this site has shown, should not be considered as definitive all over the world. The Steering Wheel did NOT have the cutouts in the spokes the first year. The Seats did not tip forward to allow access to the hatch from the door openings the first year or so. Also the reclining mechanism was more of a "Tilt" the backrest style than an actual recline. The reclining adjustment knob was on the tranny side of the seat. The Seat Back had 4 chrome Vent caps installed in the seat. Since the seat back actually moved in relation to the seat, without the seat back support arms actually moving, the spacing between the seat back and cushion is slightly higher in the first year or so. The Illuminated Heater Control Console came out only for the 73 model. The 74 changed the console, and before they weren't illuminated. You'll never get heat out of the eyeball vents or the center vent. (Unless you're down south and you've had the A /C going all day and you suddenly pop open the fresh air vent.) At least from the Heater Unit on top of the Transmission Tunnel. Throttle Controls were available ONLY on the early console series (in the U.S.) and only if the car had a Manual Transmission. The first dashes had an uncut hole above the Hazard Switch. That hole was for the Fog Lamp Switch, which very, very few U.S. cars received (if any). The Cigar Lighter and Ash Tray were located to the front of the shift handle. Later, this was used to mount the Cigar Lighter. In some transition models or possibly "restored" models, it's not unusual to discover TWO cigar lighters (one in each location) or possibly a hole on the Fuse Box Cover / Ash Tray. Additionally, the very early dashes had the Toggle Hazard Switch. This switch later had a little label put to the side to denote how to operate it. When that label was added, the area it resides in was indented to protect the label from peeling off. The Toggle Hazard Switch was eventually replaced with the PULL Hazard Switch, which received it's illumination via a Fiber Optic Cable. That Fiber Optic system also illuminated the Cigar Lighter Receptacle. The Gas Filler Door on the early models had a Latch which when turned would latch the door. At some dealerships and also enterprising owners, this was replaced with a Lock, in order to provide a Locking Door. The Gas Cap on early models was also chained to the filler neck, yet another reason for that rubber flap that pops out like a bib. I know of a few more, but anyone else want to chime in with theirs?

Whether to use Bondo or Red Cap Filler or High Fill primer will depend on how deep and how irregular the surface is around the dent. Personally, whenever I can access both sides of the sheet metal and I can tap the dent down, using a shrinking hammer or other techniques, I do my darndest to reduce that dent so that the LEAST amount of, again, one of the filler methods mentioned above is required. If you do the metal work PROPERLY, then the amount of bondo, filler, primer, etc. you use will be MINIMAL, and it shouldn't be noticeable PERIOD. If it is noticeable, then it's less than a good job, in fact, I would rate it a poor job. The reduction in value of a car is usually due to POOR bodywork rather than GOOD body work. So when it comes to the "acceptability" of using Bondo, it becomes more a question of: if you don't know that Bondo was used ......... Bondo is not the all around "EVIL" that people make it out to be. Do you honestly believe that if a car got a ding in one of the fenders as it is rolling through the assembly line that they would destroy the car? or destroy the fender? Possibly replace the fender, if that can be done, but if it can't, I'll guarantee that there's a small section of the assembly line that does nothing but repair "oopses". For what it's worth.

There are four corners to the hatch. The mounting location for the hinges to the body provides the BULK of the adjustments to the hatch. You have movement up and down to adjust for general alignment of the face of the hatch to the edges of the body. However, used properly it can also adjust the top corners versus the bottom corners. Additionally you can add spacers to one hinge between hinge and body, or hinge and hatch, or at the latch. As far as the taillights, they are one piece lens with the chrome trim you are referring to being separate from the lens. However, it is impossible to find that chrome piece separate from the lens. If you DO succeed in finding a source, PLEASE POST IT! As I'm sure there are several of us who would like to replace the chrome trim on their tail lights. The left side is usually the one to go bad as it's directly above the exhaust and the chrome piece is just plastic with a thin metal plating. The Right Side is usually in good condition, but unfortunately the sides don't interchange. New Old Stock Lenses sometimes show up on e-Bay, but they ALWAYS go for high dollars, and they are EXTREMELY rare. Used ones are a possibility, but I would DEFINITELY want to look before I bought. There are just too many things that can go wrong with that chrome piece; peeling, pitting, bubbling, wrinkling, oxidizing, losing the pins, etc. 2¢

One very important point to remember when looking at Z's, check for rust in all the hidden areas. Read some of the archives here and educate yourself as to what to look for. Next, when you are looking, buy the car that is in the absolute BEST condition you can get. Granted, you will pay more. How much more depends on the seller. However, I can't make this point strongly enough, a Fixer Upper is good, IF YOU HAVE LOTS OF TIME AND MONEY. And believe me when I say, you will EASILY invest 4-5 THOUSAND dollars upgrading a $2k car to what you will consider a 20 footer. (A car that looks good from 20' away.) Buying a $5k car that is pretty much intact, except for some cosmetic work will be MUCH CHEAPER in the long run than that $2k car needing "Fixing". Now, if you're planning on modifying it out, or doing various changes to the interior, body, paint etc, then at least get a car that has the MINIMUM amount of rust, preferably NONE. Although very honestly, if it has NONE it will probably be a garaged and babied car and you will really hate yourself for modifying it all out. Just my 2¢

Actually the liquid Electrical Tape is good stuff. I used Plasti Kote in the spray can cause I had it on hand. With regards to the fuse box. The drawing he has matches the one in the Sports Z Magazine, but those don't match Inf's. The one in Zparts could be any of them, since you never see the back. The KEY thing here is that the "GOOD" solution that was posted at ZGarage should have said that it was only good for X year Fuse Boxes. I'm sorry I don't know WHICH year, but I know it isn't the 70-71 it might be a later year, but I don't know. Therein lies why I jumped on your reply. Inf's pic clearly showed that adding that wire to join all the wires on one side would shunt two circuits that were separate AT the fuse box. In re-reading the article in Sports Z, the author also advocates tightening the crimps at the connections before soldering and sealing. I did that by using a punch and anvil. Anyhow, hope he gets his done well. 2¢

What's your handle on Zcar? Went there and no TexasZ. Are you sure you're not referring to Zcarchat.com? That's the only site where your post would get bumped to the top. Or Zdriver.com?

Mike, unless you are going for a Concours restoration, and trust me that is an extremely anal endeavour, I wouldn't worry much about it being "stock". I have a 1971, which I could put to bone stock. But I like the illuminated Heater Control Panel from the 73, and the reclineable seats from the 72+, and I've added the Throttle Control to an Automatic Car, and my Fog Lamps are Wallie Mart Specials, and I'll be finagling a Hazard Switch to act as a Fog Lamp Switch and this summer I'll be adding the Parking Lamp Switch and wiring to light up the traffic side of the vehicle (*Special Thank You to Kats). And let's not forget my Wheels, and the Louvers both back and side, and the pin-striping, and the gloss black rocker panels........ Do you get the drift? The idea is make the car YOURS. If you have a thing for White interiors, have a nut. If you want them Red, go for it. Now if you get real outlandish, send in pics and we have a special gallery for those cars. (Check out the Bright Metallic Blue Diamond Tuck) But whatever you do, its the car that YOU will be driving. Not one of us. 2¢

Better yet, post his handle on ZCar.com and let some of us have a whack at him. Nothing like a battle of wits with someone who can't even get into the fight. Hmmm, which forum? It isn't Deeman is it? He's one of them that I know that has continued to plumb new depths in human stupidity. 2¢

Carl: In all honesty, I did not disassembly my fuse box and do the solder technique. I tried but felt that the heat was going to exceed the melting point of the plastic and I just gave up. What I did do, was to use a punch and small anvil to smash down the rivets tighter, and I did that without removing the fuse holders from the fuse box itself. I believe that you can remove them from the fuse box simply by pushing in the two little tabs that stick out on each side of the fuse holder, but I'll admit that I'm going off memory and it's been months since I had the fuse box open and was working on it. Then I gave the back of the fuse box a shot with some clear Plasti-Kote in a spray can. Just enough to put a thin film of "plastic" to protect from the elements. I also replaced the headlights with the new Zenon tubes (Not the high wattage ones) and have been extremely pleased with the results. But now you got me thinking, and I'll have to get out there and check. Enrique Scanlon

In the article in Sports Z Magazine's last issue that has been cited previously and by myself above, Joe Demers makes note of this dielectric grease. His statement is that in HIGH Voltage LOW current applications, the dielectric grease does not cause problems. However, in HIGH Current situations, regardless of voltage, he recommends against it. Joe points out that dielectric grease is NON-conductive, but effective in preventing corrosion. What he recommends for the crimped connections is soldering and to be covered with some form of RTV (Room Temperature Vulcanizing) coating or Shrink-Wrap tubing. As far as how to clean that film off the back, you could grind, sand, sandblast or, since you're considering soldering at least the crimped joint, why not remove the joint from the fuse box, and use a good quality Rosin Core Solder. As long as you can get the metal hot enough the rosin usually has enough acid in it to bite through most coatings. 2¢

Just remember that the wiring for the 240 was designed with the older 55W/45W lights and not the newer 100W/90W. By doubling that wattage you are increasing the amount of current and therefore load on the wiring. If there are ANY flaws (i.e. resistance points) in your system you WILL cause problems. 2¢